Go Back   RCCrawler Forums > Scale Rigs General Tech > 1.9 Scale Rigs
Loading

Notices

Thread: 2Kind's Gelande II D90

Reply
 
LinkBack Thread Tools Display Modes
Old 09-05-2016, 07:46 PM   #81
Pebble Pounder
 
Join Date: Nov 2015
Location: Gilsum, NH
Posts: 126
Default

Got the Driver's side window box finished up. It's a mirror image of the other side so I'll save you from that. As much as I liked that drawer system in the floor, it's for another build and I've gone in a different direction.

A while back I picked up some of RC4WD's Scale Diamond Plate Aluminum Sheets (part#Z-S0533). You get two 11"x8.7" sheets for around $16. It's pretty easy stuff to work with. Metal sheers made quick work of it.
 photo 20160901_191922_zpsu2pccxen.jpg

Back at it with the wood. Slightly darker stain for inside.
 photo 20160901_211228_zpsqn9p7max.jpg

A few bit for tiding up lines.
 photo 20160904_194858_zpsgmx59rel.jpg

Not nearly as clean as I'd like. Aside fome starting over and making the boxes properly, It's the best I could do.
 photo 20160905_174115_zpsrgwqsdra.jpg
 photo 20160905_174040_zpssrmp3hl2.jpg

With the bit of play created by swapping shock mounts I thought maybe the rear inner fenders would fit with everything now. By sheer circumstance they do. I did not put the shock bolt through the fender though.
 photo 20160905_185027_zpssbo5dqjn.jpg
 photo 20160905_185017_zpsnbagak1m.jpg

At best it's going to only be seen moving, from a distance and through half a window. I'm trying to be ok with how messy it looks and move on. With the gain of roughly 1cm of depth, the floor is almost even with the bottom of the door now.
 photo 20160905_181700_zpslnvtxvfe.jpg

Still unhappy with the lip it creates though. Only because I see it causing issues in the end game.
 photo 20160905_181046_zpsz0827aej.jpg

Plan is to make a toolbox/shelving unit to sit on the bench under each window box. Most likely going to be attached by way of magnets. Lots of concealed room under there to play with now.
 photo 20160905_185548_zpseqmevala.jpg

I'm looking to get a solid floor plan done soonish so the little things are on hold. For now it's back to the seating situation. Been hesitant but yesterday I picked up a set of Axial Corbeau seats. Mostly because my LHS (Toy City-Great bunch of guys) had them in stock and once in hand.... Much nicer than I had imagined. I see why they're so popular. It'll be hard to not use them now.
2kind is offline   Reply With Quote
Sponsored Links
Old 09-06-2016, 05:22 AM   #82
Quarry Creeper
 
Join Date: May 2011
Location: scituate RI
Posts: 269
Default Re: 2Kind's Gelande II D90

Wow! I think it looks great and your doing an amazing job
ribaja is offline   Reply With Quote
Old 09-08-2016, 09:19 PM   #83
Pebble Pounder
 
Join Date: Nov 2015
Location: Gilsum, NH
Posts: 126
Default

Quote:
Originally Posted by ribaja View Post
Wow! I think it looks great and your doing an amazing job
Glad you're liking it so far. Learning a lot every day for sure. Thanks for everything Ribaja!


Hacked up whats left of the interior. Going to keep the front section. Seems easier than making one from scratch.
 photo 20160906_203632_zpspdf9lkz3.jpg

Welding it to the piece that the seats and console will be fixed to.
 photo 20160906_214841_zps4an4wjch.jpg

It all got hit with flat black. Unsure how to handle the dash at this moment.
 photo 20160908_204956_zpseenssvz4.jpg

Made up some floor panels out of the diamond plate from RC4WD. Each plate comes with a clear plastic film over the front and a blue film over the back allowing you to mark what ever measurements you need to, then peel off the films when done.
 photo 20160908_204630_zpsxzff83js.jpg
 photo 20160908_192733_zps06c8swgj.jpg

Wrapped both shifters in the same fabric the seats are made of.
 photo 20160908_204816_zps76qnysg0.jpg
 photo 20160908_192748_zpsku7bkrox.jpg

Making progress. Seats should be finished after tonight and ready to be stuck in place. Most likely the interior will all be one piece but not sure yet. I'd like to bolt it to the frame. Prolly useing the two posts on the battery tray. Plan to attach the dash to the interior but that may change. Trying to figure out the door panels next...
 photo 20160908_192854_zpsfaaaz4cf.jpg

Last edited by 2kind; 09-10-2016 at 10:17 AM.
2kind is offline   Reply With Quote
Old 09-09-2016, 06:54 AM   #84
Quarry Creeper
 
Join Date: May 2011
Location: scituate RI
Posts: 269
Default Re: 2Kind's Gelande II D90

I like the diamond plate touch is it hard to work with
ribaja is offline   Reply With Quote
Old 09-10-2016, 10:15 AM   #85
Pebble Pounder
 
Join Date: Nov 2015
Location: Gilsum, NH
Posts: 126
Default

Quote:
Originally Posted by ribaja View Post
I like the diamond plate touch is it hard to work with
Thanks! Me too.
I was quickly becoming unsatisfied with the look of the interior and had debated scraping it all and starting over. Simply adding the floor boards tied the rear to the front and brought a balance to things I was badly needing.

The diamond plate is very malleable stuff do to how thin the sheets are. No doubt more skilled folk would be able to actually build with it. I did whacked it a few times with a wooden mallet (like I do most things) and it didn't tweak the design in the sheet too much, seems rather tough. Only time will tell but should be good for things like running boards where they will see some abuse from rocks and debris. One of my biggest issues is not having a proper tool to cut clean lines with. I'm also wanting black plate for a couple things. Not sure how well paint will stick to it though. Might try dipping it in Plasti Dip.

For another option, Plastruct makes a diamond plate styrene sheet that I'm trying to get my paws on. This could become any color, a bit easier for me to work with, and cheaper. Not as tough but would be nice to have some on hand.
2kind is offline   Reply With Quote
Old 09-14-2016, 09:21 PM   #86
Pebble Pounder
 
Join Date: Nov 2015
Location: Gilsum, NH
Posts: 126
Default

I wasn't sure what else to do for the flooring. I had some of the sticky back felt left so I layed that down underneith the seats.
 photo 20160910_223407_zpsvotuk2yg.jpg

Located some Shoe Goo a while back. Figured now was a good time to try it out. Lathered up both seats and the console with a healthy dose and plunked'em down on the felt. Holds real well.
 photo 20160911_212132_zpsfgnh1zlm.jpg

My attempt at wrapping the steering wheel:
First, I glued only the middle of a thin strip of fabric around the wheel.
 photo 20160911_200533_zps99fwtlvb.jpg

Second, Wrapped thread around the wheel holding the fabric where it wasn't glued.
 photo 20160911_202938_zpsl1xzb835.jpg

Keeping the dash simple. Just a bit of Testors dark brown. I messed up the guage sticker when painting so I'm going to need something different. For now it stays like this.
 photo 20160911_210128_zpsds7fc6nf.jpg

Sorted out the doors as well. Decided to glue them right to the body. Now they finally sit perfectly in the window and just right with the interior.
 photo 20160911_210337_zpsqa7wuaha.jpg
 photo 20160911_210432_zps5gnjx9an.jpg

I was afraid of all the pieces not fitting together but they seem to be playing their parts. Much work left though.
 photo 20160911_211139_zpsidte8yd9.jpg

My best box yet!
 photo 20160914_185822_zps44cwks8q.jpg

Getting some distance on these lil hinges Two magnets (only one seen) glued at a 90 degree angle hold the lid shut and the bigger one you see in the middle holds the whole box to the interior with the help of another magnet under the inner fender.
 photo 20160914_185750_zpsr3yyidhz.jpg

They are pretty rugged lil magnets. The box wont be sliding around much if at all.
 photo 20160914_185854_zpscnrbrjw8.jpg

For some reason I want to paint it dark green. Most likely though, I'm going to keep it a grey or a dull metal of sorts. Fits real well.
 photo 20160914_191006_zps3hsvf2ki.jpg
 photo 20160914_191026_001_zpscbchv6rz.jpg

Won't open much from the inside but I don't plan on climbing in there any time soon.
 photo 20160914_191436_zpsuzqc3ris.jpg

Bonus!
Being there's a magnet on the top of the box, I am able to stack something else on it without worries of it going anywhere
 photo 20160914_191606_zpse3qj8gw9.jpg
2kind is offline   Reply With Quote
Old 09-15-2016, 01:30 AM   #87
Newbie
 
Join Date: Aug 2016
Location: Germany
Posts: 25
Default Re: 2Kind's Gelande II D90

According to all pictures I have found from 1:1 Land Rovers, your steering wheel is upside down. The two "arms" should be in the lower half of the wheel when centered, I believe. (Probably wrong in the RC4WD manual...)
DirkW is offline   Reply With Quote
Old 09-15-2016, 06:03 AM   #88
Quarry Creeper
 
Join Date: May 2011
Location: scituate RI
Posts: 269
Default Re: 2Kind's Gelande II D90

Keep up the details its looking great 2kind but I think you need to get it out and get it dirty before the winter snows start lol.
ribaja is offline   Reply With Quote
Old 09-15-2016, 09:31 AM   #89
Newbie
 
Join Date: Aug 2016
Location: Chelsea
Posts: 41
Default Re: 2Kind's Gelande II D90 (pic heavy)

Great idea for the doors. Mine never line up with the windows.

Sent from my SM-G900V using Tapatalk
Antfarm34 is offline   Reply With Quote
Old 09-17-2016, 02:29 PM   #90
Pebble Pounder
 
Join Date: Nov 2015
Location: Gilsum, NH
Posts: 126
Default

Quote:
Originally Posted by DirkW View Post
According to all pictures I have found from 1:1 Land Rovers, your steering wheel is upside down. The two "arms" should be in the lower half of the wheel when centered, I believe. (Probably wrong in the RC4WD manual...)
Good eye and thanks for checking it out! Debated this both times I've done the dash. Pretty sure you're correct all around. There is a notch in the steering column and a matching piece on the steering wheel mold that line up resulting in what you see. Always thought it a bit strange, but it's a little more secure this way. I'd say most of the time, the wheels are turnned in either direction anywho. Kind of wanting to do a simulated wheel so this will get righted when/if I find a tiny servo and can pull it off.

Quote:
Originally Posted by ribaja View Post
Keep up the details its looking great 2kind but I think you need to get it out and get it dirty before the winter snows start lol.
Thanks as always man! Couldn't agree more! In fact, got all the new electronics placed and wired up. Took it out for a quick spin around the yard. Gotta say, liking the changes.

Quote:
Originally Posted by Antfarm34 View Post
Great idea for the doors. Mine never line up with the windows.
Thanks! Glad you like'em. It was one of my biggest issues with the interior ever since day three and one of the first on the "To Do" list. Interestingly it was one of the last pieces to fall into place.
2kind is offline   Reply With Quote
Old 09-17-2016, 06:54 PM   #91
Pebble Pounder
 
Join Date: Nov 2015
Location: Gilsum, NH
Posts: 126
Default

Some time ago I got these goodies that I'm just now getting around to.
 photo 20160729_130709_zpsapvuevlf.jpg

I opted for the Holmes Hobbies CrawlMaster Pro 16T (part#HH-110100022, maybe...). With only 10mins of run time on it I can't say a whole lot yet. Between the transmitter and the Hotwire hook up there's still settings that need to be messed with. Off the get go, well worth the shiny bits for it. Much smoother and faster than the 55t I'm used to. Running a 14t pinion on 2s with stock spur gear right now and I've got a 12t and 9t on hand. Gonna play around and we'll see where things land.
 photo 20160725_122922_zpsq65wnqtq.jpg

My mess I like to call the electornics. Managed to cram everything under the bonnet. No BEC at the moment and undertaking the change over to deans on all my stuff.
 photo 20160917_180950_zpshpvifxww.jpg

The Tekin FXR Fwd/Rev Brushed ESC (part#TT1091) really is super tiny, like they all said. Actually smaller than my SR3100 receiver. You need to solder on the transsistor (I think it's called). It calls to make the connection as close as possible. Being it's so big, that makes it hard. I found multiple accounts of folk making an inch or so lead for it. That's what I did as well. Guess we'll see if there comes an issue but for now everything seems to be working fine. There's a lip on the front bumper brace that just so convienleantly fit the FXR on. Sits in front of the 540 motor, leads up, with roughly 2-3mm to spare. Also picked up the Tekin Hotwire 2.0 (part#TT1451). Very basic interface but everything I'll need seems to be there. Tweaked a couple things for now to get up and running.
 photo 20160915_190923_zpsn5fb7q29.jpg

My New2rocks stylie plate that sits on the servo makes a return. Still holding up It's holding the winch controller and the Spektrum SR300WP receiver. Spektrum is all I now aside from RTR gear. I'm a pretty satisfied customer. My DX3R has taken a beating for 9+ years now. Still run the box receiver weekly. Looking to pick up something with more channels soon. Most likely going to try a different brand just not sure which yet.
 photo 20160917_180930_zpsl8yerbei.jpg

Can't speak more highly of the C.I. foams. Growlers were much improved by adding the Lil Novas so I figured I'd try the Deuce's Wild Single Stage Closed Cell Foam for 1.9 Tires (part#CWR-3007) 1.9 Tires 4.25" - 4.19". Fit like they were made for the Tomohawks.
I' a huge fan of the 1.9 Dirt Grabbers but have failed in finding a foam that works them. The DW were too far to wide but with some trimming may work perfectly in them.

 photo 20160725_122942_zpstonfdxa5.jpg

Things are all together and fit nicely. Been having issues with my Proline Scaler shocks leaking. I put the stock 80mm's back on and really like how it sits.
 photo 20160913_212606_zpsa3aroq1x.jpg

Out the door we went....
 photo 20160911_174345_zpsj0xc0ncq.jpg
 photo 20160911_174929_zpsbchoygkp.jpg

I like the 1.9 Tomohawks just wish they were about 3-4mm smaller all around and a bit more scale looking.
 photo 20160911_175136_zpslsdzihpn.jpg
 photo 20160911_175331_zps1tv0twru.jpg

Fortunately, I snagged a set of the new Pitbulls last night. Should be here next week some time. From all I've seen, they look to be everything I've been wanting and will finally be the tire for this rig.

Last edited by 2kind; 09-18-2016 at 08:29 AM.
2kind is offline   Reply With Quote
Old 09-17-2016, 07:40 PM   #92
Quarry Creeper
 
Join Date: May 2011
Location: scituate RI
Posts: 269
Default Re: 2Kind's Gelande II D90

Nice 2kind I'm running the mamba micro x with the hh brushless 2200 stubby in the tf2 and a brushed hh torgmaster 30t expert in the scx10-2 but I've been thinking about that 16t you have. If you just need 4 channels you could get the spektrum dx4c for like a hundred.
ribaja is offline   Reply With Quote
Old 09-17-2016, 08:42 PM   #93
Pebble Pounder
 
Join Date: Nov 2015
Location: Gilsum, NH
Posts: 126
Default

Quote:
Originally Posted by ribaja View Post
Nice 2kind I'm running the mamba micro x with the hh brushless 2200 stubby in the tf2 and a brushed hh torgmaster 30t expert in the scx10-2 but I've been thinking about that 16t you have. If you just need 4 channels you could get the spektrum dx4c for like a hundred.
I came real close to getting that brushless setup. Kind of wish I had. Maybe next build

Leaning hard towards a stick controller and Spektrum does make some decent ones. I'm wanting more than four channels to play with I think. Seven or eight should be enough but all that is in due time.
2kind is offline   Reply With Quote
Old 09-18-2016, 11:06 AM   #94
Pebble Pounder
 
Join Date: Nov 2015
Location: Gilsum, NH
Posts: 126
Default

Soldering is something I have struggled greatly with for the last decade prolly. Part of the problem is not doing it enough. Other than a couple motors every now and then there wasn't a need. Also partly do to my equipment. My local Radio Shack is shutting done and selling off all their supplies so I figured now was a good time to pick up a proper soldering station
Everything to date was done with this poor lil guy.
 photo 20160918_090039_zpseyaa4jpu.jpg

Well, while out I convinced myself there was plenty of life left in the ole iron and decided to upgrade a bit further.

Picked up Bernzomatic TS8000 Map/Pro torch and few other things to start messing around with. Having absolutely no idea what I'm doing I also grabbed brass and aluminum brazzing rods.
 photo 20160918_090432_zpsi68lh4rx.jpg

Some brass and steel rods and odd bits.
 photo 20160918_093105_zpsj5j7jli7.jpg

In the past I've attempted bending tubes and rods without success. After a bit of homework and treasure hunting at the local hardware store. In the bin with kitchen drawer runner wheels I found these. I think they are for sliding glass doors and found a few different sizes.
 photo 20160918_110447_zpsg5gy0b2o.jpg

Not sure what it's called but I made a real crude version of one, I think...
It bends stuff for me. Some folk are using sockets which is brilliant, IMO. Going to fab up something a bit more proper when I get some time. For now though, it works so I thought I'd share. Maybe it will help someone else.
 photo 20160918_110600_zps1ubrhp1v.jpg

To start my first project some 3/16 steel (pretty sure) brake line was chossen.
 photo 20160918_093223_zpsm8okimad.jpg

It comes with a coating of some sort. So the first step is stripping that off. Chucked in the drill....
 photo 20160918_092739_zpsgtd1xopb.jpg

With a small piece of sand paper wrapped around the rod, pull the trigger and its gone in seconds. You may want a glove if you're doing a large piece. It gets warm.
 photo 20160918_092822_zpskf1rgkjs.jpg

Leaves you with a nice surface to work with.
 photo 20160918_093245_zpswix4nfpn.jpg

After making my measurements, bends, and cuts I had this.
 photo 20160916_173122_zpsfpp83lv9.jpg

But I need two.
 photo 20160916_175504_zpsbyqdltlz.jpg

A piece of this brass would be a tab for mounting to the body.
 photo 20160917_171300_zpshasvkwnr.jpg

Not sure if it's a weld, braze, solder, or just a mess but this was the first attempt at whatever it is. Went around whacking it on stuff and it held so I continued the process.
 photo 20160917_140712_zpsfrga73dz.jpg

After shaping the tabs with a drinder and taking a metal wire brush attachment for the dremal to it all, this was what I had.
 photo 20160917_172519_zpsjsp6u96o.jpg
 photo 20160917_172533_zpsxf2kwafw.jpg
 photo 20160917_172552_zpssrax8rc0.jpg
 photo 20160917_172724_zpsd3xwqn0s.jpg

Here's you can see how far they stick out from the body. Pretty close to where I'd like them. In 1-2mm would be perfect. Happy
 photo 20160917_173348_zpsw8bplv9g.jpg

After getting blacked they were ready for the rig.
 photo 20160917_210818_zps17fviscm.jpg
 photo 20160917_210920_zps8ea5uojy.jpg

You've prolly guessed already, and yep, rock guards for the sides. Held in place by magnets in the pictures. Hope to get them properly fixed to the body today but it serves the purpose.
 photo 20160917_212425_zpsvkhrpw0h.jpg
 photo 20160917_212222_zpsez8bz70w.jpg
 photo 20160917_212209_zpsilsnofah.jpg
 photo 20160917_212237_zpscuhrkgyz.jpg

Consumer Rant:
Completely inspired by CChand's Side Guards for the D90 body. One look and I was sold on the idea but for that price, for what they are, No Sir. I have principle disagreements with that sort of thing Don't get me wrong. I really like their products. They are of very nice if not top quality and plan to purchase more in the future but there is no need for those kind of prices. It makes it very hard to support a company with moral practices like this. Still respect must be paid where it's due. Not only the idea but the driving factor as well were instigated by them. For that I thank you.


It's small for sure but being my first metal project I'd really like to hear what yall think. Criticism, pointers, things you would have done differently, all coments welcome.

As always, Thanks for looking!
2kind is offline   Reply With Quote
Old 09-18-2016, 11:33 AM   #95
Rock Crawler
 
Join Date: Feb 2010
Location: in a Fishbowl watching time go by
Posts: 923
Default Re: 2Kind's Gelande II D90 (pic heavy)

I noticed the steering wheel on my build instuctions say to build it upside down, I sortred mine out.

What pittbulls do you have on the way ? I'm hoping its the small ones.
801RYAN is offline   Reply With Quote
Old 09-18-2016, 11:36 AM   #96
I wanna be Dave
 
Join Date: Apr 2014
Location: North Carolina
Posts: 2,254
Default Re: 2Kind's Gelande II D90 (pic heavy)

Great job on the sliders. All of us have had first times for everything in this hobby - it' the only way to learn.

Re CC Hand, the quality of their products is excellent. As far as the pricing is concerned, it's worth remembering that our hobby is very niche, and volumes for products like theirs are very low. If they knew they could sell stuff by the thousands, they could mass produce and bring the price point down. But that's probably not in the cards for their stuff, hence the higher prices. You did exactly what one should do if one doesn't want to buy - make it instead! Well done, sir.


Sent from my iPhone using Tapatalk
new2rocks is offline   Reply With Quote
Old 09-18-2016, 12:00 PM   #97
Newbie
 
Join Date: Aug 2016
Location: Chelsea
Posts: 41
Default Re: 2Kind's Gelande II D90 (pic heavy)

Once again, great work. I've thought about giving brazing a try.
I do agree that once you start making parts on your own it's hard to pay for similar parts. It just takes a little courage to try working with new materials and methods.
Keep the pictures coming. I have to go to Home Depot and pick up brazing tools .

Sent from my SM-G900V using Tapatalk
Antfarm34 is offline   Reply With Quote
Old 09-18-2016, 02:12 PM   #98
Pebble Pounder
 
Join Date: Nov 2015
Location: Gilsum, NH
Posts: 126
Default Re: 2Kind's Gelande II D90 (pic heavy)

Quote:
Originally Posted by 801RYAN View Post
I noticed the steering wheel on my build instuctions say to build it upside down, I sortred mine out.

What pittbulls do you have on the way ? I'm hoping its the small ones.
Great job on the limb risers. Going to start on mine soon.

Tires are:
The Pit bull A/T Hardcore 1.9 with Foam (Alien) PAP Kompound. Been looking forward to these for some time now.


Quote:
Originally Posted by new2rocks View Post
Great job on the sliders. All of us have had first times for everything in this hobby - it' the only way to learn.

Re CC Hand, the quality of their products is excellent. As far as the pricing is concerned, it's worth remembering that our hobby is very niche, and volumes for products like theirs are very low. If they knew they could sell stuff by the thousands, they could mass produce and bring the price point down. But that's probably not in the cards for their stuff, hence the higher prices. You did exactly what one should do if one doesn't want to buy - make it instead! Well done, sir.
thanks! First time is always a bit sketchy. After this expirence I'm left pretty confident moving forward. Very satisfied with how they turned out and found it really fun working with the torch. Was nice to get some metal in my hands again.

I will be the first to admit my ignorance towards not only bussiness practices but the company at hand . If understood correctly what you say makes sense to me. Definitely noted and for what it's worth, not over looked.
One of the outcomes I respect most about this situation is the rarity in wich you see their products being used. That rarity is not set by deman though instead it's set by "cost" plus a specutaled price. Which I get until the speculation crosses a line into vanity for me. It's something we all judge on our own level for sure.

Thanks for your thoughts! always enjoy discussion on ethics and philosophy.

Quote:
Originally Posted by Antfarm34 View Post
Once again, great work. I've thought about giving brazing a try.
I do agree that once you start making parts on your own it's hard to pay for similar parts. It just takes a little courage to try working with new materials and methods.
Keep the pictures coming. I have to go to Home Depot and pick up brazing tools .
Thank you and you should. Found it to be pretty fun. Just be careful. Not to be too cliche but cost aside, expirence gathered along the way is priceless. To now be able to make things I can't find or buy, well...you can't buy that either. I encourage you to give it a shot
2kind is offline   Reply With Quote
Old 09-18-2016, 02:53 PM   #99
Quarry Creeper
 
Join Date: May 2011
Location: scituate RI
Posts: 269
Default Re: 2Kind's Gelande II D90

Great work on the new rock guards. I'm thinking about picking up a torch and cheap bender.
ribaja is offline   Reply With Quote
Old 09-24-2016, 11:00 AM   #100
Pebble Pounder
 
Join Date: Nov 2015
Location: Gilsum, NH
Posts: 126
Default

Quote:
Originally Posted by ribaja View Post
Great work on the new rock guards. I'm thinking about picking up a torch and cheap bender.
Thanks for the compliment! It's something I put off far too long. Glad to have it there when an idea arises now.
2kind is offline   Reply With Quote
Reply

Tags
d90, gelande ii, rc4wd



2Kind's Gelande II D90 - Similar Threads
Thread Thread Starter Forum Replies Last Post
Gelande 2 d90 interior Reino_3000 Paint and Body 0 12-20-2014 11:08 PM
Gelande D90 Pickup bird8oy85 1.9 Scale Rigs 6 03-23-2014 04:54 PM
my old d90 Gelande oldrtybstrd Scale Videos! 0 08-19-2013 05:52 PM
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -6. The time now is 05:31 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com