07-01-2015, 10:39 PM | #141 |
I wanna be Dave Join Date: Oct 2007 Location: Castle Rock, WA
Posts: 8,785
| Re: Szczerba's Second CXT Build |
Sponsored Links | |
07-02-2015, 08:11 AM | #142 |
RCC Addict Join Date: Apr 2011 Location: San Diego
Posts: 1,630
| Re: Szczerba's Second CXT Build
So after staring for a bit are the wheels glue on in the front side and beadlock on the rear? Can't wait to see these graphics. |
07-02-2015, 11:16 AM | #143 |
I wanna be Dave Join Date: May 2008 Location: Baltimore
Posts: 4,442
| Re: Szczerba's Second CXT Build
Does regular CA stick to the grey material ok?
|
07-02-2015, 03:37 PM | #144 | |
I wanna be Dave Join Date: Oct 2007 Location: Castle Rock, WA
Posts: 8,785
| Re: Szczerba's Second CXT Build Quote:
http://www.rccrawler.com/forum/2-2-s...ml#post5157658 Yup, see above. CA holds fine, even on 4s and 2300kv with 15lbs TTC truck. | |
07-02-2015, 07:38 PM | #145 |
Suck it up! Join Date: Mar 2008 Location: Arkansas
Posts: 11,652
| Re: Szczerba's Second CXT Build
Delrin by design is not very porous, so you have to prep it properly before CA will stick. Scuff the crap out of it, and make sure it's super clean. Thin CA works best.
|
07-02-2015, 08:41 PM | #146 |
I wanna be Dave Join Date: Oct 2007 Location: Castle Rock, WA
Posts: 8,785
| Re: Szczerba's Second CXT Build |
07-02-2015, 09:22 PM | #147 |
Quarry Creeper Join Date: Oct 2011 Location: New Mexico
Posts: 311
| Re: Szczerba's Second CXT Build
You know I love big stuff and the rigs you build rock everytime...but I gotta ask. Whats up with the breakover angle? Is this an example of link geometry overruling capability? I dig the steelwork. Such a versatile material. When I read your builds I KNOW it will be completed and with those custom touches we all like to see. |
07-02-2015, 09:35 PM | #148 | |
I wanna be Dave Join Date: Oct 2007 Location: Castle Rock, WA
Posts: 8,785
| Re: Szczerba's Second CXT Build Quote:
Check out this truck and some of the videos. Same subframe setup. Lower links parallel to ground at ride height. One of the most capable big trucks I have ever built and drove. http://www.rccrawler.com/forum/2-2-s...ml#post5161399 Szczerba's 2.2 TTC truck Video at the ARCC TTC Produced by Hillrod RC Films This truck worked great too. Similar subframe setup. Szczerba's 2.2 CXT ... | |
07-02-2015, 09:50 PM | #149 |
Quarry Creeper Join Date: Oct 2011 Location: New Mexico
Posts: 311
| Re: Szczerba's Second CXT Build
Right on. I assume you mean that it provides a strong forward movement? I dont doubt your experience in big truck susp setups. I bet you have built more lbs of rigs than anyone on this forum. Its just that in my terrain and experiences...every mm of belly clearance you gain will help you keep your line. In my experience losing your line will end your attempt at an obstacle in a rig that big and heavy. This makes me wanna build my 1/6 avalanche and run my h2. Your cxt is what inspired me to build my h2. Rock on. |
07-02-2015, 10:02 PM | #150 | |
I wanna be Dave Join Date: Oct 2007 Location: Castle Rock, WA
Posts: 8,785
| Re: Szczerba's Second CXT Build Quote:
I wish someone was getting video of my TTC truck at the CO TTC Rubicon course. Just bouncing up and over mega big rocks with holes and gaps a plenty. No major issues with break overs. With break overs, alot of it comes from forward momentum and weight distribution, oh and wheelspeed. Don't get caught up on achieving maximum ground clearance or you'll sacrifice having weight up higher up. Again, a correctly setup suspension is key to a truck that performs on any type of terrain. I'll run this subframe setup 10 out of 10 times on a heavier truck over a truck that maximizes ground clearance. | |
07-02-2015, 10:11 PM | #151 |
Suck it up! Join Date: Mar 2008 Location: Arkansas
Posts: 11,652
| Re: Szczerba's Second CXT Build
I got to wheel the TTC truck a little bit at Disney. I can attest to its capability, and it does not at all drive like its that heavy. Surprisingly nimble, and as Szczerba said, breakover can be compensated for in your approach.
|
07-03-2015, 03:25 PM | #152 |
Tire&Foam Extraordinaire Join Date: Jun 2007 Location: C.I. Compound, Tyler, Texas
Posts: 5,601
| Re: Szczerba's Second CXT Build
More parts shipped out yesterday for this build: Titanium links to finish it out. Vaterra Ascender upgrade shocks. MIP Wraith drive shafts VP 225 SLW hubs The wheels looks great! Great job DCW! ..Uploaded from the lab @ the C.I. Compound... |
07-03-2015, 07:16 PM | #153 |
I wanna be Dave Join Date: Oct 2007 Location: Castle Rock, WA
Posts: 8,785
| Re: Szczerba's Second CXT Build
Mock up up the DCW built wheels. Too lazy to put the windshield and inner fenders back in right now. CI built axles Had to trim off axles shafts to fit hubs. Before picture |
07-04-2015, 11:15 AM | #154 |
I wanna be Dave Join Date: Mar 2007 Location: roland,ar
Posts: 5,981
| Re: Szczerba's Second CXT Build
Looks great as usual! Eddie should have a fleet by now... Cant wait to see the Freqeskinz on it.. |
07-04-2015, 12:10 PM | #155 | |
I wanna be Dave Join Date: Oct 2007 Location: Castle Rock, WA
Posts: 8,785
| Re: Szczerba's Second CXT Build Quote:
Going to do a little more metal work to protect the front fenders, full mock up, tear down and then paint the chassis. Wrap and decals were printed last week by FreqEskinZ. | |
07-04-2015, 01:01 PM | #156 |
I wanna be Dave Join Date: Apr 2013 Location: Streamwood, IL
Posts: 2,442
| Re: Szczerba's Second CXT Build
That's really coming along nicely, great job! |
07-04-2015, 09:11 PM | #157 |
I wanna be Dave Join Date: Oct 2007 Location: Castle Rock, WA
Posts: 8,785
| Re: Szczerba's Second CXT Build Thanks. Inching along towards completion. Been busy at work, lazy when I get home and sprinkle some vacation days in. Added some front and rear fender protection. Had to think of how to do the fronts as the whole front bumper is on a hinge. |
07-18-2015, 10:52 PM | #158 |
I wanna be Dave Join Date: Oct 2007 Location: Castle Rock, WA
Posts: 8,785
| Szczerba's Second CXT Build
Got the chassis finished welded and painted with engine block paint. Had to bake it for an hour at 200degs but the oven wasnt big enough, so I improvised. Wife just happened to be out of town today. Redid the driveshafts now that the two speed is in. |
07-18-2015, 11:14 PM | #159 |
Suck it up! Join Date: Mar 2008 Location: Arkansas
Posts: 11,652
| Re: Szczerba's Second CXT Build
Noticed the first pic before reading the text...knew you were home alone.
|
07-18-2015, 11:15 PM | #160 |
I wanna be Dave Join Date: Oct 2007 Location: Castle Rock, WA
Posts: 8,785
| Re: Szczerba's Second CXT Build |
Szczerba's Second CXT Build - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Szczerba's IFS SCX Build | Szczerba | Axial SCX-10 | 236 | 08-27-2016 07:24 AM |
Szczerba's 1.9 Beckworks Rebuild Build | Szczerba | 1.9 Scale Rigs | 42 | 07-04-2015 08:53 PM |
Szczerba's 2.2 CXT | Szczerba | Axial Wraith | 109 | 12-04-2013 06:08 PM |
Szczerba's Terra-X Build | Szczerba | Axial Wraith | 21 | 02-25-2013 09:10 AM |
Was Szczerba's Defender 90 Build. On to the Next. | Szczerba | 1.9 Scale Rigs | 22 | 07-07-2012 05:18 PM |
| |