|
| LinkBack | Thread Tools | Display Modes |
02-28-2018, 05:01 PM | #1 |
Newbie Join Date: Feb 2018 Location: brewster
Posts: 5
| Wraith axles splines vs scx10 axle splines
Hi this is my first ever thread and i have a question Would scx10 chubs fit on ar60 axles i only own ar60's and I need to know this information for my build. Any information is helpful and pictures would be very much appreciated. |
Sponsored Links | |
02-28-2018, 09:48 PM | #2 |
I wanna be Dave Join Date: Jan 2004 Location: Austin Texas
Posts: 3,866
| Re: Wraith axles splines vs scx10 axle splines
Its not a bolt on (Ar60s are splined, Ax10 are keyed) but they can be made to work.
|
03-01-2018, 09:04 AM | #3 |
Newbie Join Date: Feb 2018 Location: brewster
Posts: 5
| Re: Wraith axles splines vs scx10 axle splines
What modifications would have to be done in order to do this
|
03-01-2018, 12:33 PM | #4 |
Newbie Join Date: Feb 2018 Location: brewster
Posts: 5
| Re: Wraith axles splines vs scx10 axle splines
Now that im looking back i meant scx10 ii axles instead of scx10 axles.
|
03-01-2018, 08:25 PM | #5 |
RCC Addict Join Date: Jun 2004 Location: ORegon
Posts: 1,002
| Re: Wraith axles splines vs scx10 axle splines The splines are a little different, but my Vanquish AR60 c hubs will slide onto SCX10-II housings, so it can probably work the other way too with a little modification (SCX10-ii axles need a groove in the axle housing to clear/support the c hub clamping screw). The big problem you'll run into is axle shafts. AR60 shafts will not work in a SCX10-II knuckle. The distance between the inner bearing seat and the center of the joint is too long.
|
03-03-2018, 12:53 PM | #6 |
Newbie Join Date: Feb 2018 Location: brewster
Posts: 5
| Re: Wraith axles splines vs scx10 axle splines
Thanks that is actually very helpful. i was going to need the change the drive shafts anyways to do what I wanted to do. Could you post a picture of what you mean about the clamping screw.
|
03-07-2018, 12:36 PM | #7 |
RCC Addict Join Date: Jun 2004 Location: ORegon
Posts: 1,002
| Re: Wraith axles splines vs scx10 axle splines
The hole in the bottom of the c-hub clamps the c-hub to the axle housing. The axle housing has a groove around it where the c-hub mounts to clear this screw which also keeps the c-hub from sliding off once installed. |
Wraith axles splines vs scx10 axle splines - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Anyone else stripping axle splines??? | thurlo | Axial SCX10 II | 21 | 01-18-2017 03:53 PM |
MIP C Splines | alexchen86 | Axial AX-10 Scorpion | 2 | 11-14-2010 02:05 AM |
lubing splines | ax10 | Newbie General | 2 | 06-14-2009 07:34 PM |
Splines?? | WRMorrison | Tools, and Procedures | 13 | 04-27-2005 09:52 AM |
# of splines | bigsuzuki86 | Electronics | 5 | 04-09-2005 05:15 AM |
Thread Tools | |
Display Modes | |
| |