****CDW-4130-6mm outputs for the Axial transmission****

[CRAWLER DESIGN WORKS]

Crawler Design Works - 4130 chromoly - 6mm outputs for the Axial transmission, they have no flat spots, just a pin hole for revo and maxx yoke pins. The spur gear side output was lengthened so that the yokes will clear the spur gear. I lengthened the other output a little so that I could taper back to the bearing.Also the bolt flanges are thicker.SOLD OUT price is $38 plus shipping




http://i174.photobucket.com/albums/w109/yotachump/AX10outputs.jpg
http://i174.photobucket.com/albums/w109/yotachump/sideview.jpg
http://i174.photobucket.com/albums/w109/yotachump/tranny3d.jpg
http://i174.photobucket.com/albums/w109/yotachump/tranny3d-2.jpg

Heres a Pic to show the clearance with the 96t
http://i174.photobucket.com/albums/w109/yotachump/96t.jpg


SOME MORE PICS


http://www.rccrawler.com/forum/showpost.php?p=1225865&postcount=111
http://www.rccrawler.com/forum/showpost.php?p=1225010&postcount=108

[dieselfuel]

oh yes, maxx shafts are back!!

[BitHed]

..oh now these will be interesting...good job...

[The Real Dogman]

you have my attention. Thank for the Chance"thumbsup" Put me down!!

[Mnster]

Any chance of just offering just one side? I have a 4X2 baja truck. Also might be handy for the folks with VF dig units. Or people who only want to upgrade the rear shaft for strength or custom digs. Also why is one longer then the other? I have a hard enough time craming the large maxx shafts between two axles.

Nice work though, these look great."thumbsup"

[Soya]

Also why is one longer then the other? I have a hard enough time craming the large maxx shafts between two axles.




To clear the spur, yo ;)

[666]

Put me down for 2!!:D

[CRAWLER DESIGN WORKS]

Any chance of just offering just one side? I have a 4X2 baja truck. Also might be handy for the folks with VF dig units. Or people who only want to upgrade the rear shaft for strength or custom digs. Also why is one longer then the other? I have a hard enough time craming the large maxx shafts between two axles.

Nice work though, these look great."thumbsup"

I will think about offering just one side.

[Offroader5]

Nice....can run Revo's on the Axial now :twisted:

Not only will the lengthened output clear the larger yokes, but should also allow the use of slightly larger spurs. "thumbsup"

[John]

Put me down for two sets.

Thanks,
John

[Just Zach]

I absolutely need a set. Please send a pm when they are ready.

[jimbiss]

Sweet, those look great "thumbsup""thumbsup"

[4xFord]

put me down for sure!"thumbsup"


now how about some 6mm axle pinions?

[Reflection]

Put me last in line for 2 sets. Don't need them at the moment,but will soon.

[rc4x4nut]

In for a set.

[CRAWLER DESIGN WORKS]

Nice....can run Revo's on the Axial now :twisted:

Not only will the lengthened output clear the larger yokes, but should also allow the use of slightly larger spurs. "thumbsup"

yep, you can run a 96t

[BILLYGOAT]

put me down for a set please.

[Tanis]

now how about some 6mm axle pinions?
Swap a Wheely King pinion in, 6mm and drilled for the crosspin already;-)"thumbsup"

[EeePee]

Swap a Wheely King pinion in, 6mm and drilled for the crosspin already

How about this?

http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXPZX2&P=M

[BitHed]

...VERY well thought out unit YotaChump...but are you SURE you want to put up ALL your R&D for 'everyone' to see? Would hate to see it picked up by another manufacturer...

[cartronicshn]

Take two"thumbsup"

[Sparky J]

I would like the one side also in order to run with the VF"thumbsup"

[sidewinder]

I'll take one.

[rn38]

put me down!!

[bcrofts]

put me down

[McCutchenca]

I definitely want a set. PUT ME DOWN

[Phatmac]

Please put me down for a set, these are beautiful, thanks for the great R&D.

[area51caraudio]

please put me down for a set"thumbsup"

[Trugg]

Please put me down for 1 set for sure!!!"thumbsup"
I'll even pre-pay:lol:

[Tanis]

How about this?

http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXPZX2&P=M
That be the one EP"thumbsup"
I'll take a set Anthony8)..... I mean "Put me Down" for a set:lol:

[HiloDB1]

Are all 25 sets spoken for? If not put me down for a set.

[4xFord]

Thank you Tanis and EP, never knew if they worked for sure. Good to know."thumbsup"

That be the one EP"thumbsup"
I'll take a set Anthony8)..... I mean "Put me Down" for a set:lol:

[Tanis]

Thank you Tanis and EP, never knew if they worked for sure. Good to know."thumbsup"
Yep, the WK and AX10 R&P's will interchange, In one of my trucks I have WK ringgears with Axial pinions right now8)

[CRAWLER DESIGN WORKS]

Do you guys want these Black oxide coated? Or you just want to spray paint them? If you want them Black oxide coated, it will be another week:x,But will be no extra charge for the coating:lol:.I am going to do all of them or none of them on the coating, not just a couple. Let me know what you guys want.

Also Black oxide does not offer very good corrosion resistance. I think paint will do better. But its up to you guys.
Heck, I will even paint them for you:lol:

[cartronicshn]

I'd wait for the coating, but that's just me;-)

[The Real Dogman]

Black Fo Sho!!!"thumbsup""thumbsup"

[Tanis]

I'll just take mine as is. Can't see them anyway;-)

[JohnRobHolmes]

I don't care really, cause it will be all greasy by the time I get my hands on it. Black oxide is alright, but wouldn't paint interfere with the bearing fit?

[CRAWLER DESIGN WORKS]

Fine, Raw it is.

[Reflection]

I want mine chrome.

[area51caraudio]

if at all possible i'd prefer both sides to be short sides (dont care about running the larger spur, - not sure if this would be possible?

[4xFord]

I want mine chrome.

How about Ti Ni?

[McCutchenca]

I'll take mine however I can get 'em. I'm just glad to be getting such a sweet part.

[CRAWLER DESIGN WORKS]

Well the machine shop called me today and said that they are running a little behind and I wont see them until Sunday night:x This means sales wont start until Monday after work or Tuesday After I get off work.Sorry but this is beyond my control. Hope you guys understand, Sorry Again.

[The Real Dogman]

No Problem!!! Thanx for the update!! I will wait happily!!

[Reflection]

I'm good with it,take your time.

Guess it'll be a bit longer for the chrome finish?????

[CRAWLER DESIGN WORKS]

I'm good with it,take your time.

Guess it'll be a bit longer for the chrome finish?????

Ill polish yours for you if it will make you happy:lol:

[JohnRobHolmes]

That is to be expected with a machine shop, sometimes they underestimate or overbook. I'm good with waiting.

[666]

So is whoever that is on the list getting these or is it first come first serve?

[CRAWLER DESIGN WORKS]

So is whoever that is on the list getting these or is it first come first serve?

The first 25 people one the list are first.

[EeePee]

Then what? Got more? Lots and lots more? A few more? Millions more? No more?

:D

[Tanis]

I'm cool with it Anthony8). Are you going to PM the first 25, or are we going to have to keep an eye on this thread?;-)

[CRAWLER DESIGN WORKS]

Then what? Got more? Lots and lots more? A few more? Millions more? No more?

:D

Yea, I have more, and more coming:lol:

[CRAWLER DESIGN WORKS]

I'm cool with it Anthony8). Are you going to PM the first 25, or are we going to have to keep an eye on this thread?;-)

I am going to PM the first 25, and then the rest of you guys have at it until there sold out:lol:

Here is the list of the first 25 people, let me know if I missed you out, your you dont want on the list.

1.dieselfuel
2.The Real Dogman
3.666
4.Offroader5
5.John
6.Just Zach
7.4xFord
8.raptorman57
9.rc4x4nut
10.BILLYGOAT
11.cartronicshn
12.sidewinder
13.rn38
14.bcrofts
15.McCutchenca
16.Phatmac
17.area51caraudio
18.Trugg
19.Tanis
20.HiloDB1
21.EeePee
22.________
23.________
24.________
25.________

[Tanis]

Nice, just so everybody knows, if anybody takes mine, I'm gonna start banning people:-P:-P:lol::lol:


Just kidding;-)...or am I?:twisted:

I know I'm looking forward to these, no matter how long it takes to get my mitts on them. I've been very happy with the quality of your other products8)

[EeePee]

Oh well hot diggity, throw me on the list.

And will one of you good fellas share with me which of the two Maxx yokes to get? I intend to grab the WK input shaft that I posted a link for, also. You'd be so helpful, please and awwwllllright. My search button has been permanently removed due to too much searching. Search abuse.

[The Real Dogman]

LMAO "search abuse"!! Now thats funny right there!!

Or is it?? I've been working to long today!! Hell I dont know!!

Fkit I'm tired, I'm going back to work!:shock:

[4xFord]

Oh well hot diggity, throw me on the list.

And will one of you good fellas share with me which of the two Maxx yokes to get? I intend to grab the WK input shaft that I posted a link for, also. You'd be so helpful, please and awwwllllright. My search button has been permanently removed due to too much searching. Search abuse.

The one with the bigger hole in it! But seriously, glad to return the favor, it is 4928X."thumbsup"

[area51caraudio]

this (below) is a great tip but don't forget to order the wheely king ring and pinion set, i found this out the hard way when the new wk pinion shafts showed up and had no hole in it for the cross pin. (hpi855 is the part# I believe - don't quote me on that though)


How about this?

http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXPZX2&P=M

[nj05nismo]

will the new front fit a stock rear output? Im running a VF dig and keep killing front outputs. Any chance of getting on the list and only paying for the front? Are there plans for a shorter front output?

[Phatmac]

I wanted to put together a list of parts that make this a MAXX shaft bolt-together operation, so far I have the following, let me know if I've missed anything:


Qty-Description--------------------------------------------------------Part#----Tower#----cost ea---total
1x---Crawler Design Works - 6mm outputs --------------------------------------------42.00---42.00

2x--HPI Differential Final Gear Set Nitro RS4 MT---------A855----LXTB48-------5.79--11.58
2x--HPI Gear Shaft 5x6x29mm Wheely King--------------86810---HPIC8810----7.69--15.38

2x--Traxxas Diff Output Yokes w/Screw Pins 2.5 (2)---4928X----TRAC4929--4.79----9.58
1x--Traxxas Half Shafts Long T-Maxx (2)-------------------4951X----LXSP55------7.69----7.69

-------------------------------------------------------------------------------------------------Grand Total $88.23
----------------------------------------------------------------------------------------------------------------plus S/H

Also, I would like to try to run a 96t Spur "because I can", is the WK Spur compatible with the Axial tranny? Are there any other options? Will the Kimbrough Differential gear work?

Please inform me of any omissions/corrections. Cheers.

[EeePee]

Can't we put the Axial pinion on the WK input shaft (posted Tower link)?

[area51caraudio]

NO, The axial pinion uses a cross pin, the wk shaft has two flat spots on either side and the pinion gear matches, with no cross pin or hole drilled in it for one

Can't we put the Axial pinion on the WK input shaft (posted Tower link)?

[area51caraudio]

Phatmac, The only spurs that I have found to work are the kimbrough spurs for traxxas vehicles and I believe the biggest is an 87 tooth 48pitch (at least that's all I could find) - if anyone knows of any other spurs that willl work - please chime in

[EeePee]

Ooooooh, okay, now I gotcha, I was a bit confused with your previous post, but now I understand. Thanks man, getting old and been a while since I've been inside my axles.

[SpyderMonkee]

Put me down for a set. Your TF lockers rock!

[CRAWLER DESIGN WORKS]

Sorry guys, I have no word from the shop yet.:roll: This is why I dont do pre orders. I will let you guys know as soon as they call.Thanks for your patience.



I guess I know next time not to post anything up until I have it in hand now.


once again I am VERY sorry, they have never done this to me before.

[HiloDB1]

Dont worry about it. I'm just glad I got the chance "thumbsup"

[Sparky J]

Forgot me #22"thumbsup"

[CRAWLER DESIGN WORKS]

Forgot me #22"thumbsup"


Thats because I don't know it the outputs will line up with the VF bolt pattern( I have no way to check). And in this first batch I don't have any extra front outputs, They where all made in pairs.Do you want the pair?

[CRAWLER DESIGN WORKS]

The shop just called about 1 minute ago and said Thursday.I am very very sorry for the extra wait.

Thanks again for you patience"thumbsup"

-Anthony

[Tanis]

The shop just called about 1 minute ago and said Thursday.I am very very sorry for the extra wait.

Thanks again for you patience"thumbsup"

-Anthony
Not an issue8)8) I'm just glad you're making some stout outputs, these are needed"thumbsup"

[rn38]

yay i can put my cobalt back in!!!!

[Phatmac]

After thinking about it yesterday, why can't I just drill a hole in my axial diff outputs? I figure that they're steel or hardened steel, so I might have to use a cobalt steel bit, but it saves on parts. From all that I've read, it looks like the T-Maxx tranny outputs are 5mm, so the parts list would be as follows:

Qty-Description---------------------------------------------------Part#----Tower#----cost ea---total
1x---Crawler Design Works - 6mm outputs --------------------------------------------42.00---42.00

TRAXXAS PARTS
1x--Diff Output Yokes w/Screw Pins 2.5 (2) [6mm]-----4928X----TRAC4929--4.79----4.79
http://www3.towerhobbies.com/cgi-bin/wti0095p?FVPROFIL=++&FVSEARCH=4928X&search=Go
1x--Trans Output Yokes T-Maxx 2.5 (2) [5mm]-----------4927X----LXDDT2------5.79----5.79
http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXDDT2&P=ML
1x--Traxxas Half Shafts Long T-Maxx (2)-------------------4951X----LXSP55------7.69----7.69
http://www3.towerhobbies.com/cgi-bin/wti0095p?FVPROFIL=++&FVSEARCH=LXSP55&search=Go
-------------------------------------------------------------------------------------------------Grand Total $59.37
----------------------------------------------------------------------------------------------------------------plus S/H

This will leave my better able to afford the HPI HD gears, which give you a 1pc diff pinion/shaft combo with a hole.

The axial diff input does have a flat, so it should be easy to center and drill. I'll let you know what size when I assemble all the pieces.

To recapitulate: use the diff output yokes on your new cro-mo CDW outputs, drill the axial diff pinion shafts for the center pin for the transmission output yokes, add shafts, and voila! indestructable diff output and cheap, strong, lightweight shafts. Priceless. :lol:

[CRAWLER DESIGN WORKS]

I have them on my hands NOW. I will start the sale as soon as I am done PMing all the people on the list.


http://i174.photobucket.com/albums/w109/yotachump/AxialOutputs003.jpg

[Tanis]

I have them on my hands NOW. I will start the sale as soon as I am done PMing all the people on the list.Yeah!!! I will warm up the "Send Money" button in my paypal:lol:"thumbsup"

[HiloDB1]

Money sent "thumbsup"

[CRAWLER DESIGN WORKS]

All pm's have been sent. you can buy them now

[rn38]

Just sent payment for 1 set!!! wooohooo. cant wait now

[CRAWLER DESIGN WORKS]

bcrofts, please get ahold of me I have no shipping address from you.

[Phatmac]

Man these look nice. Great work Anthony! My payment has been sent, and I anxiously await their arrival. Off to the LHS to assemble the needed Maxx parts now. Yeehaw! "thumbsup"

[CRAWLER DESIGN WORKS]

Man these look nice. Great work Anthony! My payment has been sent, and I anxiously await their arrival. Off to the LHS to assemble the needed Maxx parts now. Yeehaw! "thumbsup"
You sent payment without any shipping address. you need to edit your paypal.

[JohnRobHolmes]

Payments sent for "service" wont show a shipping addy. It needs to be for "goods"

[CRAWLER DESIGN WORKS]

All orders have been shipped.EXCEPT the 2 people that sent payment with out any address or if you payed with a echeck.

[CRAWLER DESIGN WORKS]

Payments sent for "service" wont show a shipping addy. It needs to be for "goods"

Thanks for that info JRH"thumbsup" I never knew that, but it makes sense.

[Biscuit]

Do you know when you might have your next batch in? I would like to buy a set.
biscuit1973@bellsouth.net

Thanks

[CRAWLER DESIGN WORKS]

Do you know when you might have your next batch in? I would like to buy a set.
biscuit1973@bellsouth.net

Thanks


They are not sold out. PM me;-)

[Biscuit]

just paypal'ed you. thanks.

[CRAWLER DESIGN WORKS]

All current new orders have been shipped.
Thanks everybody"thumbsup"

[crawl rookie]

Whats up with the outputs pictured on you avater? looks like double the mounting holes to me"thumbsup"

[Phatmac]

Phatmac, The only spurs that I have found to work are the kimbrough spurs for traxxas vehicles and I believe the biggest is an 87 tooth 48pitch (at least that's all I could find) - if anyone knows of any other spurs that willl work - please chime in

This is why we need to support our LHS. I went in and told Luke at my local Hobbytown that I needed a big spur. From reading the forums I knew the Traxxas/Kimbrough spurs fit, and after clarifying that they were indeed 48 pitch, he handed me a 93 and 96 Kimbrough gear. I bought the 96 after comparing the holes to the 87t traxxas spur, and it works!

The part I got was Kimbrough #142 96 Tooth 48 Pitch Precision gear, and it set me back $4.00.

I installed in on my Axial without the rear driveshaft, (it rubs the stock yoke--can't wait until my new outputs come).

With my 55t integy and a 12t Robinson Racing pinion, and my 7 cell NiMH split pack, it tops out a whopping 2 mph, covering 10 feet every 3 seconds!

I'll post pics with the outputs and the 96t spur when I put it all together.

[CRAWLER DESIGN WORKS]

Whats up with the outputs pictured on you avater? looks like double the mounting holes to me"thumbsup"

Those are a special Outputs for me:flipoff::lol::lol: they require a bearing with 10mm ID. and then reduce down to 8mm. NUKE PROOF:twisted:8)

[Reflection]

NUKE PROOF:twisted:8)

You wanna bet a 3 piece chicken dinner on that?"thumbsup"

[area51caraudio]

Payment and PM sent"thumbsup"

[CRAWLER DESIGN WORKS]

You wanna bet a 3 piece chicken dinner on that?"thumbsup"
Sure, All double it, and some:lol:

[4link4eva]

Got any of these outputs left? I have an Axial tranny in between two custom Maxx axles with Revo shafts, and being pushed by a 6t Cobalt motor on 3s. I'll NEED these outputs. :lol:

Anyway, can you give me a quote for a set of these posted to the UK?

Cheers, Paul. :)

[CRAWLER DESIGN WORKS]

Got any of these outputs left? I have an Axial tranny in between two custom Maxx axles with Revo shafts, and being pushed by a 6t Cobalt motor on 3s. I'll NEED these outputs. :lol:

Anyway, can you give me a quote for a set of these posted to the UK?

Cheers, Paul. :)

Sure, PM me please.;-)

[rn38]

Just got these in the mail and man they are NICE!!!!

Great job"thumbsup"

Gotta get to work tomorrow to try and break these.:twisted:

[CRAWLER DESIGN WORKS]

...........

[Tanis]

Mine arrived yesterday, but I only had a couple of minutes to get online yesterday. Very nice outputs Anthony, I like them"thumbsup"8)

[HiloDB1]

Mine came in the mail yesterday too. But I wasnt home to get the package. So I get to go to the post office to pick it up along with my cobalt 7t. Cant wait.

[Trugg]

Got my outputs today in the mail....man are they SWEET!!8)
Just finshed installing them.
Thanks again Yotachump for the excellent product"thumbsup"

[CRAWLER DESIGN WORKS]

Mine arrived yesterday, but I only had a couple of minutes to get online yesterday. Very nice outputs Anthony, I like them"thumbsup"8)

Just got these in the mail and man they are NICE!!!!

Great job"thumbsup"

Gotta get to work tomorrow to try and break these.:twisted:

Got my outputs today in the mail....man are they SWEET!!8)
Just finshed installing them.
Thanks again Yotachump for the excellent product"thumbsup"

you are very welcome."thumbsup" Hope you abuse them:lol::lol:

[Phatmac]

Mine came in the mail today! "thumbsup""thumbsup""thumbsup"

If they work as good as they look, I'll be grinning for weeks :lol:

I'll post pics with the 96t and your skid plate as soon as I get it assembled.

Thanks again for offering such an awesome product.

[HiloDB1]

Got my outputs today in the mail....man are they SWEET!!8)
Just finshed installing them.
Thanks again Yotachump for the excellent product"thumbsup"
What shafts and yokes did you use? Did you go with the setup Phatmac listed?

[EeePee]

Yo Ant, got mine today, they look very nice, thanks buddy.

"thumbsup"

[Trugg]

What shafts and yokes did you use? Did you go with the setup Phatmac listed?


Yes, I guess I am using what Phatmac listed...
-Maxx shafts (TRA4951X)
-Maxx trans. yokes (5mm) (TRA4927X) (for axial diff. outputs)
-Maxx diff yokes (6mm) (TRA4928X) (for CDW 6mm trans. outputs)
8)

[Phatmac]

As promised here's a pic with the outputs and the 96 tooth Spur. Lots of room. I drilled out the 6mm Traxxas yokes with a 15/64 drill--this removed the internal flat spots and allowed for a good press fit.

I just mocked it up so all the spacers aren't there for for the motor plate, and the set screw/shafts aren't screwed in on the Traxxas parts, but you get the idea.

I am amazed at how nice these outputs are, the threads are perfect and went together with the stock gear and screws as good if not better than the factory parts. Beautifully designed Anthony, and very nicely machined.

110% satisfied :)

http://i175.photobucket.com/albums/w139/Walkthesnail/CDWOutCrop_1.jpg
[sorry for the shadows, shooting a low-key image is bad enough, but I had to use the camera flash instead of my homemade light box--otherwise I would have never got to bed last night]

[Tanis]

you are very welcome."thumbsup" Hope you abuse them:lol::lol:
Abuse will be forthcoming:twisted::twisted: I'm going to throw them in the rockracer first. 25T Holmes handwound on 4cell lipo......I can hear the R&P's crying now, as they are now the weakest link:lol:

[CRAWLER DESIGN WORKS]

Abuse will be forthcoming:twisted::twisted: I'm going to throw them in the rockracer first. 25T Holmes handwound on 4cell lipo......I can hear the R&P's crying now, as they are now the weakest link:lol:

slipper? or aluminum tranny gears? if not I think your tranny gears will give out first.:lol::lol:

[rob_b]

Perfect fit on Revo yokes! Thanks Anthony;-)

[Flyin Hawaiian]

pm me if there is any left"thumbsup"

[CRAWLER DESIGN WORKS]

pm me if there is any left"thumbsup"I am running out the door right now for vacation, I will PM as soon as I get back.

Thanks

[Reflection]

These worked perfect today. Threw a 5t cobalt on 3 cells at them today without any sign of weakness. Pushed the 5t up to temps around 250,busted 2 spur gears and ripped my rear upper link mount off though:lol:

[BitHed]

...these DO look great...YotaChump could i possibly get a price shipped to Japan when you get back from vacation? Thanks mate...

[Phatmac]

These worked perfect today. Threw a 5t cobalt on 3 cells at them today without any sign of weakness. Pushed the 5t up to temps around 250,busted 2 spur gears and ripped my rear upper link mount off though:lol:

You sir, are a wild man! What drive shafts are you using?

[4link4eva]

Payment sent for a set of outputs and postage to the UK :D

Please PM me when they are posted, as I REALLY need these things soon, need to practice for the UK Nats.

Thank you very much, you have been a great deal of help, my good sir. :wink:

Cheers, Paul.

[CRAWLER DESIGN WORKS]

I am back and will be catching up with everyone tonight.
Thanks
-Anthony

[Reflection]

You sir, are a wild man! What drive shafts are you using?


:lol:

Pede females doubled up in the front and a steel shaft in the rear. My dig set up is built around Pede shafts,so I need to stick with that size. I used to twist off 2-3 rear shafts every comp. I built some steel shafts and don't break that anymore. Could put Revo's up front,but then I'd break something else. Shafts and spurs are cheap easy fixes,so I'll keep my fuse at my front shaft or the spur."thumbsup"

[CRAWLER DESIGN WORKS]

pm me if there is any left"thumbsup"

PMing now

...these DO look great...YotaChump could i possibly get a price shipped to Japan when you get back from vacation? Thanks mate...
Sure
Payment sent for a set of outputs and postage to the UK :D

Please PM me when they are posted, as I REALLY need these things soon, need to practice for the UK Nats.

Thank you very much, you have been a great deal of help, my good sir. :wink:

Cheers, Paul.
Shipped

Check your PM's and get back to me ASAP please.

I just PM'ed you my cell #
Just talked to you on the phone

[CRAWLER DESIGN WORKS]

Anybody interested in a 8mm version? I am doing a second run soon, and will do a 8mm version the same price as the 6mm

[mauromj]

Would you be able to go a stock sized one (like length wise?)

[CRAWLER DESIGN WORKS]

Would you be able to go a stock sized one (like length wise?)
6mm?

[4xFord]

Anybody interested in a 8mm version? I am doing a second run soon, and will do a 8mm version the same price as the 6mm

What drive shafts are 8mm?

[CrawlinClodKiller]

Punishers? 8mm is the size of a savage pinion.

[mauromj]

6mm?

Yes, just 6mm

[CRAWLER DESIGN WORKS]

Would you be able to go a stock sized one (like length wise?)
Yes, just 6mm

what shafts are you going to use?maxx? going to run a small spur?

[Mic]

How did I miss these? They look great. The 4 link mount I got from you a while back is working great"thumbsup"

[CRAWLER DESIGN WORKS]

Any chance of just offering just one side? I have a 4X2 baja truck. Also might be handy for the folks with VF dig units. Or people who only want to upgrade the rear shaft for strength or custom digs. Also why is one longer then the other? I have a hard enough time craming the large maxx shafts between two axles.

Nice work though, these look great."thumbsup"

you want just the short side?

[lime]

I'll take some of the 6mm if you have any left.

pm sent.

[CRAWLER DESIGN WORKS]

I'll take some of the 6mm if you have any left.

pm sent.

Did you not get my PM I sent yesterday??I am 100% sure I PM'd ya. Please let me know if you didnt get it. I will send it again.

Thanks
-Anthony

[lime]

Did I not PM you back yesterday??I am 100% sure I PM'd ya. Please let me know if you didnt get it. I will send it again.

Thanks
-Anthony

I got the first one, maybe you never got my reply.

no worries.

pm me your paypal addy for two pairs and shipping ( I think it was 14 or so) and i'll send you some $$.

[CRAWLER DESIGN WORKS]

I got the first one, maybe you never got my reply.

no worries.

pm me your paypal addy for two pairs and shipping ( I think it was 14 or so) and i'll send you some $$.

your right, I never replied to the second one, Sorry about that, I get so many a day I get lost sometimes. PM sent.

Thanks"thumbsup"
-Anthony

[CrawlinClodKiller]

Can you make stock replacements? The stock size is critical in my build. If so pm me a prize and how long it would take. thanks

[CRAWLER DESIGN WORKS]

Can you make stock replacements? The stock size is critical in my build. If so pm me a prize and how long it would take. thanks
I will see what I can do, can they be a little longer then stock?

[CRAWLER DESIGN WORKS]

GIVEAWAY (http://www.rccrawler.com/forum/showthread.php?t=124581)

[CrawlinClodKiller]

Two of the short side would work I guess. I was just thinking the stock 5mm size. I am gonna use stampede steel yokes, so the 5mm is just easier.

[Kinson]

Add me for two sets, please.

[rojo]

pm sent "thumbsup"

[area51caraudio]

Anthony, I got my outputs a week or so ago and I've got to say although the service and the workmanship was great, i'm a little upset cause the long side rubs where my upper links are mounted to my chassis, now I have to design a new chassis"thumbsup":!: damn"thumbsup":!: oh well - unless there is a way that i could buy just a short side to replace the long side (not sure which oine is threaded cause there already installed)see below:

I moved the link up one hole in the pics so i doesen't tear up my yoke or rod end

http://i293.photobucket.com/albums/mm74/msedsp/DSCN2789.jpg

http://i293.photobucket.com/albums/mm74/msedsp/DSCN2791.jpg

http://i293.photobucket.com/albums/mm74/msedsp/DSCN2790.jpg

http://i293.photobucket.com/albums/mm74/msedsp/DSCN2792.jpg

either way - thanks for ther great product and quick shipping"thumbsup"

[mauromj]

I am using the ckrc dig setup so I would need 100% stock size. I wouldnt care if they were a tad longer or anything.

[CRAWLER DESIGN WORKS]

I am using the ckrc dig setup so I would need 100% stock size. I wouldnt care if they were a tad longer or anything.

they will be less then 1/16 longer;-)

[mauromj]

Will these be available for purchase of 1 or both of them?

[CRAWLER DESIGN WORKS]

Will these be available for purchase of 1 or both of them?

It will be a set. They should be available SOON :lol:

[Locked Up]

they will be less then 1/16 longer;-)
Will they be 5 or 6 mm?

[Reflection]

Will they be 5 or 6 mm?

Stock is 5mm correct.....

I would need 100% stock size. I wouldnt care if they were a tad longer or anything.

they will be less then 1/16 longer;-)

[sparky0068]

Put me down for a set of 6mm. Thanks!

[CRAWLER DESIGN WORKS]

Put me down for a set of 6mm. Thanks!

The are in stock and Shipping out daily:lol::lol:.

[Locked Up]

Will the 5mm stock length (or 1/16 longer) have a hole for a pin or will they just have the flat side?

Just curious ... I'm in for a set either way"thumbsup"

[CRAWLER DESIGN WORKS]

Will the 5mm stock length (or 1/16 longer) have a hole for a pin or will they just have the flat side?

Just curious ... I'm in for a set either way"thumbsup"

2 flat spots only

[Hawk Mortimer]

Put me down for 2 5mm (1/16" longer) sets.

Thanks
Hawk

PS
Will you contact us when they are ready?
Thanks

[Locked Up]

2 flat spots only
Splendid.

When can I order? My mouse is hovering over the send money button in paypal "thumbsup"

[CRAWLER DESIGN WORKS]

Splendid.

When can I order? My mouse is hovering over the send money button in paypal "thumbsup"

You can order when they come in.I will start a new thread for the 5mm version shortly.

[CRAWLER DESIGN WORKS]

I have one non threaded 6mm short side if anybody wants to buy it for a 2x4 project or something

[Locked Up]

You can order when they come in.I will start a new thread for the 5mm version shortly.
Any thoughts as to when they might come in? I don't want to miss out8)

[CRAWLER DESIGN WORKS]

Any thoughts as to when they might come in? I don't want to miss out8)

most likely next week. here's a pic for you:lol:

[Locked Up]

So there will be 2 flat spots on it?

I was kinds hoping there would just be one to improve strength even more ...

[hotwheels000]

PM sent for the 6mm long set

[helhedded]

So there will be 2 flat spots on it?

I was kinds hoping there would just be one to improve strength even more ...


I'm thinking 2 spots will allow for 2 screws to keep it secure!

[CRAWLER DESIGN WORKS]

Just got a new batch in, I have these instock and ready to start shipping again:lol:

[MTHead]

PayPal sent.. :mrgreen:

Thinking these will do the Holmes Puller justice. ;)
Thanks!!!

[toy4crawlin]

I would like a set, . running Revo and other 6mm shaft.
What Diameter is the spur side output? I'd like a flat spot on that side but not motor side

Need before Sept.

Thanks
Rian

[Reflection]

I would like a set, . running Revo and other 6mm shaft.
What Diameter is the spur side output? I'd like a flat spot on that side but not motor side

Need before Sept.

Thanks
Rian


Both sides are 6mm. The spur side is just longer to push the yoke away from the spur"thumbsup" Thats really only needed though if guys gear down or run stock gearing. An 81t spur will clear a Revo yoke flat up against the tranny."thumbsup"

Flat spots not really needed since theres a hole for a cross pin."thumbsup"

[Offroader5]

Still have these available? I'd like to pick up a set if so. I am ready to get rid of these small shafts and go back to my Revo's :lol:

Anyone tried these with the DNA dig? Any fitment issues?

[CRAWLER DESIGN WORKS]

Still have these available? I'd like to pick up a set if so. I am ready to get rid of these small shafts and go back to my Revo's :lol:

Anyone tried these with the DNA dig? Any fitment issues?

Yes, these are still available,but I don't know if I will be doing another run though, so once there gone they might be gone for good.

[Trugg]

Anyone tried these with the DNA dig? Any fitment issues?


Yes, I use it with the DNA dig unit works great. I use the long CDW 6mm output in the front to clear the spur gear.

[CRAWLER DESIGN WORKS]

Labor Day weekend sale

$35 plus shipping

[dragnz24]

Pay Pal Sent. :-P:-P:-P

[CRAWLER DESIGN WORKS]

sale Ends Tonight At 12:00

[dancomer]

dammit i want these i am waiting for a paypal payment to clear!!!!!!!!!!!!!!!!!!!!!!! please o please let me get a set i need something that will allow me to run bigger shafts that wont split or crack, or plain ol fall out. let me know what you can do for me PLEASE....pm would be great

[PipeDreams]

Hey man got a question for you.... I'm getting a DNA dig on my axial tranny but I like to run allot of gear and I'd love to run the longer front output you have.... One issue is I'd like it in a smaller 5mm out like the vf dig is so I can run the same kind of shafts front and rear. Any plans of making a longer stock sized front output that would work with the DNA rear half? Thanks I see this has been brought up but I never saw answer. Thanks

[CRAWLER DESIGN WORKS]

dammit i want these i am waiting for a paypal payment to clear!!!!!!!!!!!!!!!!!!!!!!! please o please let me get a set i need something that will allow me to run bigger shafts that wont split or crack, or plain ol fall out. let me know what you can do for me PLEASE....pm would be great

PM me"thumbsup"

[Mortimer Snerd]

Got my outdrive in the mail yesterday. Looks great, and I'm stoked to get it installed and be able run unmodded Maxx shafts!

[2JSC]

Still have some? PM me!

Ivy needs MAXX shafts. "thumbsup"

[rubiredunlmtd]

got my outputs put on. wow!
you da man! those cheap stock alum are shiet!
thanks!

[2JSC]

One question...

What are you guys doing for the 5mm axle ends? I read something about T-maxx tranny outputs being 5mm and working... is this correct?

[PipeDreams]

Ya older ones are 5mm!

[alabamaman]

pm sent need a set of these paypal ready !!!!!!!!just need to know where to send it .

[flybird]

I 'd like to order one set , PM me for Paypal info include International shipped price. TKs.

[flybird]

I 'd like to order one set , PM me for Paypal info include International shipped price. TKs.

highly appreciate your soonest reply.

[CRAWLER DESIGN WORKS]

I 'd like to order one set , PM me for Paypal info include International shipped price. TKs.

highly appreciate your soonest reply.

PM sent.

[ak907killa]

im also running ckrc dig and need a set of outdrives i have a comp october 5th let me know if you can help and how much shiped to alaska thanks"thumbsup"

[CRAWLER DESIGN WORKS]

im also running ckrc dig and need a set of outdrives i have a comp october 5th let me know if you can help and how much shiped to alaska thanks"thumbsup"

Wouldn't you want the 5mm version??

[CRAWLER DESIGN WORKS]

Back in stock

[birdie]

Are you going to be doing any more? I'd like one so i can use it with my WK axles...

[Xtant3150c]

Are you going to be doing any more? I'd like one so i can use it with my WK axles...

x2 "thumbsup"

[juan916]

I would like a set of the 5mm with cross pin hole when you get them in


tagged

[Useree]

Do you still have the longer 5mm version? Would like to get my hands on them.

[birdie]

Back in stock

I'll grab a set... PM with details please :-)

[birdie]

yotachump - I've sent you a PM... I want to get a set of these asap... :-) Cheers

[sbarnesvta]

Hey looking for a set of these asap, sent you a pm thanks

[Trugg]

One question...

What are you guys doing for the 5mm axle ends? I read something about T-maxx tranny outputs being 5mm and working... is this correct?


For the axle end (pinion shafts) you can use a WheelyKing pinion gear and pinion shaft.
The WK outputs are 6mm and have a hole for the screw-pin8) It's a simple drop-in upgrade... and a huge improvement"thumbsup"

[XPLORx4]

Do these outputs work with the stock Axial yokes? Or do you recommend using the ones that are available at rpphobby? Last question: can you use a slipper clutch and a 96-tooth pinion?

[CRAWLER DESIGN WORKS]

Do these outputs work with the stock Axial yokes? Or do you recommend using the ones that are available at rpphobby? Last question: can you use a slipper clutch and a 96-tooth pinion?

no these will not work with stock axial yokes...The ones you are looking for would be the ones Rpphobby sells or CKRC...With the 6mm outputs and a slipper you can run a 96t

[5150bronco]

Hey Yota, my friend is interested in 5mm long shaft for VF dig.

You have one? Thanks.

or 5mm chromo short version????

[Cycleeric]

Will these work with MIP shafts and Im getting a DNA dig? Im interested in getting a set if you got them that will work for me

[pdm]

I need a set, PM sent 8)

[po' riggity]

Hmmm interesting.. I may need a set of these... I have a WK, and want to run an Axial trans with WK axles and shafts... I am assuming these are what I need in the axial trans to allow the 6mm WK driveshafts to fit? Is there anything else I'll need?
Scott

[Firefox]

Are these etill available and if so, how to order ?

[Gatekeeper]

all I can say about these output shafts is ...bulletproof....I have had them in my rig for a while now and they are still holding up great.Thanks for the great product:D

[nmanuel01]

I hope they are, pm'd yesterday still no response, i snapped my stock outputs yesterday as well

[BitHed]

...how much are these shipped to Japan? And how is availability?

[BigBlackCummins]

all I can say about these output shafts is ...bulletproof....I have had them in my rig for a while now and they are still holding up great.Thanks for the great product:D
I agree these outdrives are great and take alot of abuse!! Mine are still holding up without any problems."thumbsup" I'm putting in my HH 7T puller real soon, I know my outdrives will hold, but we'll see what will be next on my "have to upgrade because I broke it" list...:lol:

--Yotachump, I got a buddy interested in buying for his rig too, you got these in stock right now:?:

[Duuuuuuuude]

I need a set as well...

[Firefox]

Just wondering if anyone has problems with the longer side trying to move from side to side too much, deflecting due to torque, or transmission problems after installing these.

thanks

[ctrwannabe]

Pm'ed you about a set I also need these :lol:

[ScalerLover]

Update on these please ?
Ripped the rear output off my stocker at the OSAS yesterday :cry:

[theslowguy]

This might be a dumb question but, what do you do to attach that maxx shaft to the axle? Just snapped off the front outdrive off my truck and I want these but this is the only question I have."thumbsup"

EDIT: Got it all figured out. Picked up the yolks and the maxx shafts. PLEASE tell me these outputs are still available I NEED these!

[ScalerLover]

Ive already talked to him in PM's guys.

Hes not making them...... :|

[CRAWLER DESIGN WORKS]

CAn I get a list of how many people what these. I just might do another run if I get enough interest."thumbsup":)

1.
2.
3.
4.
etc

[dieselfuel]

CAn I get a list of how many people what these. I just might do another run if I get enough interest."thumbsup":)

1.
2.
3.
4.
etc


me.

[MadForce]

I am #2 then! I also guess ecoli, Novas'ark, I think Mudsy was also looking for some.

[R/CMaxximus5.0]

yes.

[Biscuit]

I'll take a set. Possibly two.

[ecoli]

I'll take two sets. No need to go begging again in the future then :D!

What's "enough interest" ;)?

[JeremyH]

Put me on that list!

[alabamaman]

ONE maybee two set please!!!!!!!!!!!!!!!!!yes he shoots he scores I need these.

[Duuuuuuuude]

CAn I get a list of how many people what these. I just might do another run if I get enough interest.

Just to be clear...are we actually talking 6mm or 5mm?

If its 6mm...I'm definately interested.

[BigSki]

count me in for a set of 6mm outputs.

[RPMJ]

I'm in for a set"thumbsup"

[CRAWLER DESIGN WORKS]

Lets actually keep the list going. Copy and paste it in your reply. just like you do when signing up for a comp.

1. Dieselfuel
2. Madforce
3. R/Cmaxximus5.0
4. Biscuit(maybe 2 sets)
5. ecoli (2)
6. JeremyH
7. alabamaman (maybe 2 sets)
8. Duuuuuuuude
9. Bigski
10. RPMJ
11.
12.
13.
14.
15.

[R/CMaxximus5.0]

I may be interested in 2 sets depending on price."thumbsup"
I'm spreading the word to fill up your list!

[TrailDawg362]

1. Dieselfuel
2. Madforce
3. R/Cmaxximus5.0
4. Biscuit(maybe 2 sets)
5. ecoli (2)
6. JeremyH
7. alabamaman (maybe 2 sets)
8. Duuuuuuuude
9. Bigski
10. RPMJ
11. TrailDawg362 (maybe 2 also)
12.
13.
14.
15.

[1beatjeep]

--------------------------------------------------------------------------------

1. Dieselfuel
2. Madforce
3. R/Cmaxximus5.0
4. Biscuit(maybe 2 sets)
5. ecoli (2)
6. JeremyH
7. alabamaman (maybe 2 sets)
8. Duuuuuuuude
9. Bigski
10. RPMJ
11. TrailDawg362 (maybe 2 also)
12.1beatjeep.
13.
14.
15.

[Nate08]

1. Dieselfuel
2. Madforce
3. R/Cmaxximus5.0
4. Biscuit(maybe 2 sets)
5. ecoli (2)
6. JeremyH
7. alabamaman (maybe 2 sets)
8. Duuuuuuuude
9. Bigski
10. RPMJ
11. TrailDawg362 (maybe 2 also)
12.1beatjeep.
13.Nate08 - maybe 2 sets as well
14.
15.

[Mudsy]

1. Dieselfuel
2. Madforce
3. R/Cmaxximus5.0
4. Biscuit(maybe 2 sets)
5. ecoli (2)
6. JeremyH
7. alabamaman (maybe 2 sets)
8. Duuuuuuuude
9. Bigski
10. RPMJ
11. TrailDawg362 (maybe 2 also)
12.1beatjeep.
13.Nate08 - maybe 2 sets as well
14.Mudsy- (might get two set)
15.
http://www.rccrawler.com/forum/images/statusicon/user_offline.gif http://www.rccrawler.com/forum/images/buttons/report.gif (http://www.rccrawler.com/forum/report.php?p=1998585)

[1beatjeep]

any update on this yet

[CRAWLER DESIGN WORKS]

any update on this yet
I need a min of 30 people.

[JeremyH]

30 people or 30 units ordered? If it's "units ordered", then put me down for another set...

[RPMJ]

If it helps put me down for 2 sets"thumbsup"

[CRAWLER DESIGN WORKS]

30 people or 30 units ordered? If it's "units ordered", then put me down for another set...
30 units will work...Also I will need pre orders when as soon as I get the quote and ETA in.

[Nova's Ark]

Can you produce just the front output in this order?
I have three rear outputs and only one front. I would be interested in at least one, possibly two front out puts. These are the best outputs on the market. I am glad to see you are making more"thumbsup".

[CRAWLER DESIGN WORKS]

Can you produce just the front output in this order?
I have three rear outputs and only one front. I would be interested in at least one, possibly two front out puts. These are the best outputs on the market. I am glad to see you are making more"thumbsup".

For you I will get two extra fronts made."thumbsup"

[1beatjeep]

did you get your 30 sets yet

[Nova's Ark]

For you I will get two extra fronts made."thumbsup"

Make it four extra fronts then please"thumbsup" This is the best thought out product for an Axial transmission aside from the trans itself. Great work Anthony8).

[StIcK kInG]

put me down for @ least 1 set please, maybe 2? thanks, PP ready"thumbsup"

[chrisjlittle]

I'll take at least 1 set, maybe 2

1. Dieselfuel
2. Madforce
3. R/Cmaxximus5.0
4. Biscuit(maybe 2 sets)
5. ecoli (2)
6. JeremyH
7. alabamaman (maybe 2 sets)
8. Duuuuuuuude
9. Bigski
10. RPMJ
11. TrailDawg362 (maybe 2 also)
12.1beatjeep.
13.Nate08 - maybe 2 sets as well
14.Mudsy- (might get two set)
15. Stick King
16. Chrisjlittle

[1beatjeep]

any update on these.Did you get your 30 sets

[dda01015]

1. Dieselfuel
2. Madforce
3. R/Cmaxximus5.0
4. Biscuit(maybe 2 sets)
5. ecoli (2)
6. JeremyH
7. alabamaman (maybe 2 sets)
8. Duuuuuuuude
9. Bigski
10. RPMJ
11. TrailDawg362 (maybe 2 also)
12.1beatjeep.
13.Nate08 - maybe 2 sets as well
14.Mudsy- (might get two set)
15. Stick King
16. Chrisjlittle
17. dda01015

[StIcK kInG]

any update on these.Did you get your 30 sets

is it 30 sets needed or 30 members? if it helps out any ill take 2 sets"thumbsup"

[Firefox]

How much is a set anyway ?

[1beatjeep]

is it 30 sets needed or 30 members? if it helps out any ill take 2 sets"thumbsup"

just add them up is it close to 30

[StIcK kInG]

just add them up is it close to 30


so i guess the count is 24 then including all the maybe 2's:mrgreen:. ok well were getting closer. i just cant believe more people dont want a set or two of these:shock:

[Tanis]

1. Dieselfuel
2. Madforce
3. R/Cmaxximus5.0
4. Biscuit(maybe 2 sets)
5. ecoli (2)
6. JeremyH
7. alabamaman (maybe 2 sets)
8. Duuuuuuuude
9. Bigski
10. RPMJ
11. TrailDawg362 (maybe 2 also)
12.1beatjeep.
13.Nate08 - maybe 2 sets as well
14.Mudsy- (might get two set)
15. Stick King
16. Chrisjlittle
17. dda01015
18. Tanis"thumbsup"

[RPMJ]

1. Dieselfuel
2. Madforce
3. R/Cmaxximus5.0
4. Biscuit(maybe 2 sets)
5. ecoli (2)
6. JeremyH
7. alabamaman (maybe 2 sets)
8. Duuuuuuuude
9. Bigski
10. RPMJ(2)
11. TrailDawg362 (maybe 2 also)
12.1beatjeep.
13.Nate08 - maybe 2 sets as well
14.Mudsy- (might get two set)
15. Stick King
16. Chrisjlittle
17. dda01015
18. Tanis"thumbsup"
I need two sets"thumbsup"

[XJ Farmer]

I'll take 2 sets also. My Unimog scx-10 keeps eating them up.

Thanks

Farmer

[JeremyH]

Are we close to the minimum number yet??

[hessian18]

You can put me in line for a set....

[EeePee]

1. Dieselfuel
2. Madforce
3. R/Cmaxximus5.0
4. Biscuit(maybe 2 sets)
5. ecoli (2)
6. JeremyH
7. alabamaman (maybe 2 sets)
8. Duuuuuuuude
9. Bigski
10. RPMJ(2)
11. TrailDawg362 (maybe 2 also)
12.1beatjeep.
13.Nate08 - maybe 2 sets as well
14.Mudsy- (might get two set)
15. Stick King
16. Chrisjlittle
17. dda01015
18. Tanis
19. EP kicks everyone's butt

[Tanis]

1. Dieselfuel
2. Madforce
3. R/Cmaxximus5.0
4. Biscuit(maybe 2 sets)
5. ecoli (2)
6. JeremyH
7. alabamaman (maybe 2 sets)
8. Duuuuuuuude
9. Bigski
10. RPMJ(2)
11. TrailDawg362 (maybe 2 also)
12.1beatjeep.
13.Nate08 - maybe 2 sets as well
14.Mudsy- (might get two set)
15. Stick King
16. Chrisjlittle
17. dda01015
18. Tanis
19. EP kicks everyone's butt
20. XJFarmer(2 sets)
21. Hessian18



29 by my count...