Clock Transmission drawing

[nathanlima]

Hey guys i have been working on a Clock transmission plate to post up as a pdf for people to use, if they like it. But I'm thinking i would like some thoughts on the drawing so far so i can work best for everyone. or if i have made a Monday morning mistake on it. thank for your guys help.

http://i29.photobucket.com/albums/c273/nathanlima/RC/tran-1.jpg

[RockCrawlingKid]

Very Nice!! allz i need is the PDF, now. good job!

[HndsWthtShdws]

Center lines would be nice, it makes it easier to line up a punch so you can drill holes. 5 sets or so of center lines would be nice for the motor screw slot, that way we can drill 5 holes and file the rest. 2 sets for the motor bearing slot should be enough.

Hole sizes would be nice.

2 overall dimensions (X&Y) would help when looking for a piece of scrap.

[Offroader5]

Don't forget a way to bolt it down to the skid. Maybe design a flap of sorts at the bottom edge that can be bent 90 degrees after you cut the design out.

[nathanlima]

I didn't want to put a mount on it because I don't know how each person is going to want to mount the bottom part of there transmission. Which would change were the mount on the plate would be. I was going for something that everyone can use no matter how they mount it. But if you or anyone else would like anything added special to it PM me and i can draw it any way you want it.

[nathanlima]

Very Nice!! allz i need is the PDF, now. good job!

email sent

[DirtRacinFool]

Looks good, can I get a PDF sent to me?

[SnoopMaxx]

Originally Posted by RockCrawlingKid http://www.rccrawler.com/forum/images/buttons/viewpost.gif (http://www.rccrawler.com/forum/showthread.php?p=1226536#post1226536)
Very Nice!! allz i need is the PDF, now. good job!


x2 can I have one PLZ
c",)

[nathanlima]

I'll send them out tomorrow morning when i get on my computer. If any one else wants one let me know and i will send the PDF off all at once.

[HndsWthtShdws]

After you print it make sure everything lines up. Sometime printers scale jobs slightly even though you selected 1:1. When I make templates like this I like to draw rulers in the X & Y directions so its easy to check.

[RockCrawlingKid]

once i get a copy ill put it on my wikispace if it's ok with u(i say thanks to whoever i get it from).

[iceman320]

I also would like a pdf of this motor plate please. thanks.

[krush groove]

I'd like a PDF also, please :)

[friscokidd]

PM'ed ya for a PDF:)

[nathanlima]

once i get a copy ill put it on my wikispace if it's ok with u(i say thanks to whoever i get it from).

Thats cool with me. I would do it, but i don't know how.

[Garcol]

PM'd for a PDF as well...
"thumbsup"

[RockCrawlingKid]

it on me wikispace see siggy!

[nathanlima]

it on me wikispace see siggy!

since i sent it BCC i got one. and when i opened it to look at it it was like two times the size. i fixed it and resent the email. sorry about the mess up every one.

[RockCrawlingKid]

it all good on my wikispace now too!!!

[DeaDShorT]

Nice work guys"thumbsup" I'll be using this soon. The resized version is dead nuts8)

[mutiny22]

PM'ed you for a PDF

[DeaDShorT]

Just FYI...you will end up having to trim off one or more of the mounting points on the trans case to allow motor clearance...not a big deal on some of the custom chassis and the commercially available chassis out now, but it may be a dissapointment for someone trying to still use the stock chassis.

[nathanlima]

Just FYI...you will end up having to trim off one or more of the mounting points on the trans case to allow motor clearance...not a big deal on some of the custom chassis and the commercially available chassis out now, but it may be a dissapointment for someone trying to still use the stock chassis.

thats true. but if you do a tummy tuck you can keep most of you chassis. that was my plans, but i started working on something else for now.