****CDW-4130-Stock Replacement outputs for the Axial transmission****

[CRAWLER DESIGN WORKS]

Crawler Design Works - 4130 chromoly - Stock Replacement outputs for the Axial transmission, they have 2 flat spots. The outputs were lengthened(a little over 1/32") so that I could taper back to the bearing.Also the bolt flanges are thicker.FOR SALE NOW, price is $38+shipping (Shipping $3.00 for First class or $5.00 for priority)






http://i174.photobucket.com/albums/w109/yotachump/CDW%20PARTS/5MMoutput007.jpg

[666]

Howz about some VF dig outputs? :-P

[CRAWLER DESIGN WORKS]

Howz about some VF dig outputs? :-P
How about a 4130 DIG???????;-):lol:

[666]

How about a 4130 DIG???????;-):lol:

Ok, I am game..........

[eric113]

Ok, I am game..........

X2 :)

[Reflection]

Ok, I am game..........

X 2,546

[robert97dodge]

Yeah what they said!!!! "thumbsup"

[CRAWLER DESIGN WORKS]

Ok, I am game..........

X2 :)

X 2,546

Yeah what they said!!!! "thumbsup"

I thought this was a output thread??????not a dig thread.:lol:

[2JSC]

With these and my chromo lockers, the driveshafts are going to be screaming for mercy! "thumbsup"

[Reflection]

With these and my chromo lockers, the driveshafts are going to be screaming for mercy! "thumbsup"

Run Revo's and put your fuse at the spur gear. It's a cheap easy fix."thumbsup"

[Robbob]

whats the thickness of the two flat spots? im wondering since I run the CKRC dig unit and had to file the rear output down to 3mm.

my stock aluminum ones are getting torn up and was looking at the 3Racing ones but Id be more for a local independent if they will work.

thanks


btw - will your other outputs bolt to these? Im thinking Emax front shaft and because of my dig Pede rear shaft

[2JSC]

Run Revo's and put your fuse at the spur gear. It's a cheap easy fix."thumbsup"

Revo's are 5mm? I thought they were 6mm... thanks for the tip! 8)

[Reflection]

Revo's are 5mm? I thought they were 6mm... thanks for the tip! 8)


They are 6mm. So are Maxx yokes and I run them on my 2.2. Look up the maxx shaft mod in the Axial section. Any shaft can be bolted up then.8) You will have to run a smaller spur though. You can run a 87t with maxx yokes. It's very tight,but it'll clear.....might need to clearence the yoke 2 or 3 thousandths. Since Revo's are larger than maxx yokes,you'll have to go down on the spur. I run an 81t spur in my super running an Axial tranny with Revo's....pleanty of room. You might be able to squeeze an 84t spur on there with Revo's,never tried it though. 81t spurs are much better.

[2JSC]

Might just wanna run Yota's 6mm outputs then. "thumbsup"

[CRAWLER DESIGN WORKS]

All yesterdays orders have been shipped"thumbsup"

[Reflection]

Might just wanna run Yota's 6mm outputs then. "thumbsup"


Thats what I'm running. Bombproof."thumbsup" My point was that if you had the 5mm,you can still work with them and have strength."thumbsup"

In some cases,the 5mm will work better for some set up's. Like if a guy has a drive line dig set up built around Pede shafts and steel Traxxass yokes. You can still run a Revo on the front shaft."thumbsup"

Thanks to Anthony,he's gave us many options for drive line strength.8)

[Whirlybird]

Got mine today and tested them out, they work great. Thanks CDW

P.S. Running stock tranny, no dig.

[2JSC]

Thanks to Anthony,he's gave us many options for drive line strength.8)

Very true... you can even run a 6mm shaft in the rear and 5mm in the front if shaft diameter size is an issue... there are a number of ways you can setup your driveline now. "thumbsup"

I'll have to place an order once the kit comes in.

[CRAWLER DESIGN WORKS]

Still have some instock and ready to ship.

[Siggy]

I got mine a few weeks ago and they really fits so well. These outputs are awesome and a perfect match for my 7t Cobalt Puller. Thanks for the great product and fast delivery! "thumbsup""thumbsup"

[CRAWLER DESIGN WORKS]

Sale Over

[toytech93]

A bump for a great product !

[CRAWLER DESIGN WORKS]

I have extended the sale, they are still on SALE

[mongoose]

I have a VF dig and MIP driveshafts, will I be able to use these?

[helhedded]

I recieved my outputs today. It was around 1pm on Monday (2 days a go) when I ordered them, and they shipped out a few hours later.:shock:


Thanks Anthony! They look great and are heavy as hell compared to the stockers."thumbsup""thumbsup"

[barbaricboye]

any left?

[CRAWLER DESIGN WORKS]

any left?
Yep:lol:

[hiliftdude]

how many ya got left

[CRAWLER DESIGN WORKS]

back in stock

[Mic]

I received them today. FAST"thumbsup" Like all your stuff very nice!

[barbaricboye]

got these quick(fast shipping), good shipping rate since I bought 3 products at once......the skid plate is genius...the outputs are also great(didnt realize they come with two flat parts and a longer "shaft", i just bought em cause they were 4130, my mips arent going anywhere once I find more set screws.)

didnt set the 4 link up yet, lazy(not sure of upper link placement, etc). but even the blemed 4 link looks nicely crafted.

thanks

[ScorpioCrawler]

any chance you'll be getting some more for sale anytime soon?

[rubiredunlmtd]

yes i need 2 of these as well good sir!

[CRAWLER DESIGN WORKS]

any chance you'll be getting some more for sale anytime soon?

yes i need 2 of these as well good sir!


http://www.ckrccrawlers.com/shop/index.php?main_page=product_info&products_id=1188

[baldchris]

any idea when you are getting more in?

[K Riccardi]

pm sent.

[CRAWLER DESIGN WORKS]

any idea when you are getting more in?

I will know when I will be getting these in next week.

[jays68yak]

Id like to get a set once they are back in stock. Are they made in the bay area? Whats the chance of being able to pick them up? (although shipping is less then gas) Can they be ordered with a hole in the ends for maxx shafts?

[CRAWLER DESIGN WORKS]

BACK IN STOCK

[Locked Up]

CKRC says out of stock. How can I order directly from you?


And out of curiosity ... any chance I could get 1 specially made without the flat spots?

[Offroader5]

Do you have these with holes already drilled? Or...are these hardened? I'm wondering if it's something I could drill myself.

[juan916]

i'm also looking for the ones that fits the max shafts and have the pre drilled hole so the long pin set screw goes through it

[viking06]

No stock ??

[CRAWLER DESIGN WORKS]

Do you have these with holes already drilled? Or...are these hardened? I'm wondering if it's something I could drill myself.

No sorry, I dont have any with holes drilled. yes, you can drill them your self.
i'm also looking for the ones that fits the max shafts and have the pre drilled hole so the long pin set screw goes through it

you are looking for the 6mm version then.

No stock ??

I have them instock.

Also RPP hobby and CKRC carry them also.

http://www.ckrccrawlers.com/shop/index.php?main_page=product_info&products_id=1188
http://www.shop.rpphobby.com/searchquick-submit.sc;jsessionid=5BEF1D686BC657F632280B85F212A B30.qscstrfrnt02?keywords=CDW

[SwanSong]

Any idea of when these are gonna be avaliable again? I'd like a set.

[CRAWLER DESIGN WORKS]

Any idea of when these are gonna be avaliable again? I'd like a set.
yep, mid week next week:-P

[viking06]

Great !! "thumbsup"

[SwanSong]

yep, mid week next week:-P

perfect. just as my stock ones are done for.

[CRAWLER DESIGN WORKS]

BACK INSTOCK:-P

[nathanlima]

The ones for the CKRC dig are working killer! Thanks man"thumbsup"

[bob1961]

i have a set of these output shafts and noticed one side won't work with the DNA dig i have....the output shafts that come with the dig unit has alum output shafts....so this means i will have one steel and one alum output shaft....how has those with this set up have done with it.......bob

....

[SDheavymetal]

do you make them 5mm and long for so i can put a 96 spur gear on it. I have MIP drive shafts. Matt

[5150bronco]

i have a set of these output shafts and noticed one side won't work with the DNA dig i have....the output shafts that come with the dig unit has alum output shafts....so this means i will have one steel and one alum output shaft....how has those with this set up have done with it.......bob

....

this is the same issue my buddy is having.

Do your screws that go together with shaft have threads on one side?

He has the VF dig with cdw shaft long in rear and black stock in front.

what should he do? I know you cant run MIP with rear 6mm cdw shaft.

just wanted to put this out there for him.

[Skin Krawler]

Okay, I just seen a guy yesterday at the Millerton Lake compitition with these replacement output.s I rounded mine out. They talked you up pretty good and said these are the best out there. I looked at CKRC and they have the same description, and the same picture as you. Their's is $24 dollars and yours is $38. Could you elaborate here?

[4xFord]

Okay, I just seen a guy yesterday at the Millerton Lake compitition with these replacement output.s I rounded mine out. They talked you up pretty good and said these are the best out there. I looked at CKRC and they have the same description, and the same picture as you. Their's is $24 dollars and yours is $38. Could you elaborate here?

I have them instock.

Also RPP hobby and CKRC carry them also.

http://www.ckrccrawlers.com/shop/index.php?main_page=product_info&products_id=1188
http://www.shop.rpphobby.com/searchquick-submit.sc;jsessionid=5BEF1D686BC657F632280B85F212A B30.qscstrfrnt02?keywords=CDW

Reading is good. :lol: He supplies the other vendors with them, and yes, they are the bomb! "thumbsup"

[Skin Krawler]

I typed the last message, you'd think I could read....

Let me break it down for ya Barney Style for the other readers."thumbsup" I was told CDW "makes these replacement outputs" What I was asking is:

1. If you make them, why are they more expensive coming from the source?

2. How is it justifiable CKRC sells your stuff $14 cheaper? I mean, if you make them, I'd rather take the middle man out and put my money in your hand, but not at this price difference.

3. Did I use too big of words for you 4xFord?:lol:

[KING BLING]

Let me help you. We were selling the CDW outputs and have recently come out with our own version. That is why our lockouts are less money.

CDW's are made in the usa and are of the highest quality. They are a little beefier then our new outputs, so the cost is worth it.

[Skin Krawler]

Thank you. That's what I wanted to know.

[customax10]

how do i order these?

[CRAWLER DESIGN WORKS]

how do i order these?

PM me"thumbsup"

[Robbob]

you got pm on these ......

[Slowkrawl]

Run Revo's and put your fuse at the spur gear. It's a cheap easy fix."thumbsup"
I am not trying to hijack a thread, but what do you mean? My buddy has been having trouble keeping driveshafts in one piece. While I am at it, is there anything other than an axial shaft or a stampede(i believe that's the other shaft..) that can be used? It's a pain in the arse fixing shafts all the time.

[spinyard]

yota i have been trying to get a hold of you, i would like to buy a set or two of these are they still avail?

Thanks!

Dan

[Bart bender]

I am not trying to hijack a thread, but what do you mean? My buddy has been having trouble keeping driveshafts in one piece. While I am at it, is there anything other than an axial shaft or a stampede(i believe that's the other shaft..) that can be used? It's a pain in the arse fixing shafts all the time.

REVO axle shafts with the fuse "weak link" at the spur, "slipper"

[cascade crawler]

bump:roll:

[cascade crawler]

yota you have a pm and a email please respond!

[cascade crawler]

FORGET ABOUT IT I GOT SOME BETTER ONES!!!!!!!:flipoff:

[CRAWLER DESIGN WORKS]

I Dont make these anymore...Ever since CKRC STOLE my design and started selling them cheaper then me I have stopped making them...Look CKRC is even still using my picture:evil::roll:


http://i174.photobucket.com/albums/w109/yotachump/Untitled-2.jpg

[4xFord]

Yep, I sure like their pimp cane copy as well. Sorry Anthony they were a great product. "thumbsup"