******CDW Berg OTA/BTA steering******

[CRAWLER DESIGN WORKS]

Crawler design Works limited Edition OTA/BTA steering kit

Kit is designed to be used with AXIAL knuckles...Kit does NOT work with clocked axles...Kit comes with everything in the pics. All mounting hardware is NEEDED.$60 shipped priority mail to the USA

SOLD OUT

http://i174.photobucket.com/albums/w109/yotachump/New%20berg%20pics/CDWBERGSTEERING121.jpg

http://i174.photobucket.com/albums/w109/yotachump/New%20berg%20pics/berggggg001.jpg

http://i174.photobucket.com/albums/w109/yotachump/New%20berg%20pics/berggggg002.jpg

[DISTURBIN' tha PEACE]

Pm sent

[Offroader5]

Aww..that looks sweet. Wish it would fit the AX axles :-( :lol:

[Mic]

Looks good. Are they compatible with the stock axial knuckles or just the high clearance ones like in the photo? This is on my have to get list "thumbsup"If only I could live without my battery on the axle. Also how about a top view. Is the servo furter back on the axle than the stock setup? (IE servo horn on the same plain as stock)

[CRAWLER DESIGN WORKS]

Looks good. Are they compatible with the stock axial knuckles or just the high clearance ones like in the photo? This is on my have to get list "thumbsup"If only I could live without my battery on the axle. Also how about a top view. Is the servo furter back on the axle than the stock setup? (IE servo horn on the same plain as stock)


works with both knuckles. I prefer the high clearance knuckles....yeah the servo is farther back the stock.

[CRAWLER DESIGN WORKS]

Forgot to mention that there is some minor work that needs to be done once you receive the kit.

[BLUEJEEP]

PM sent

[Hawk Mortimer]

PM sent. "thumbsup"

Thanks,
Hawk

Payment sent.

Hawk

[WheelinKing]

pm'd

[chip cross]

I got my OTA/BTA today. I started on swapping everything over it took about 40 minutes to install and works very, very well. "thumbsup"

http://i192.photobucket.com/albums/z229/chip_069/1238033262.jpg

Sorry for the crappy cell phone picture.

[DISTURBIN' tha PEACE]

Chipper, what's the steering rod length? From inside the rod ends.

[chip cross]

Chipper, what's the steering rod length? From inside the rod ends.
Like 6 3/8 eye to eye

FYI I am using Vanquish Products Ax-10 High steer knuckles and Axial 1X6MM Bender spacers and everything works like a charm. "thumbsup"

The drag link for the steering is a TLT-1 susp. link with E/T maxx rod ends.

[dieselfuel]

i got mine in and installed today as well. the fit an finish is unbelievable, as soon as i get a set of VP knuckles ill be good to go.

http://i303.photobucket.com/albums/nn123/4x4Junkie/DSC_0254.jpg

[run2jeepn]

Just bought me one... Can't wait...

[dieselfuel]

Just bought me one... Can't wait...


you won't be disappointed! ive got my VP knuckles on the way so mine will be done soon!

[CRAWLER DESIGN WORKS]

Got a few PM's on how to connect the clamp on the back, you run a set screw through the clamp from the bottom.

[juan916]

PM sent

[saniel68]

Anthony, any more kits left? I would like to order a second one if so. "thumbsup"

[Just Zach]

I got mine today, super quick shipping and everything looks first class"thumbsup"

[Shane_744]

CDW OTA Berg steering kit went together great. Fast shipping as well.
Parts and fitment were great. Nice clean edges and tight tolerances.

Took some pictures along the way. You have to make/have some small spacers and hardware but it isn't hard to complete, I did it "thumbsup". And your axle cannot be clocked.

Did some brief testing and everything works great. Cleans up that front end too.

[wrightcs77]

Sent a PM, would like to get a steering set up.

[run2jeepn]

Got mine installed today...."thumbsup"
http://i34.photobucket.com/albums/d133/run2jeepn/DSCF2928.jpg

[4XADICT]

Anyone have a part # for the 3x25 set screw ? All I found was a HPI 3x30 everything else is 16mm or less .

[redracerd]

where is the site that i can order one of these kits

[run2jeepn]

Smallparts.com

SSCP-M35025-10

Only 2 left

[4XADICT]

Thanks , that helps alot .

[DiEzel]

Availability yota ?

[CRAWLER DESIGN WORKS]

Availability yota ?
Still have a few sets left.

[run2jeepn]

Do you plan one for the Bully's?

[Siggy]

Do you plan one for the Bully's?

X2 "thumbsup"

[CRAWLER DESIGN WORKS]

Do you plan one for the Bully's?

No sorry.

[RC Shocker]

Are these still available? I know another 2 weeks have passed. Please pm info if so.

Thanks.

[CRAWLER DESIGN WORKS]

sold out

[3.3 Over]

looking forward to the clocked kit for berg

nice set up !!

[Pdog7]

looking forward to the clocked kit for berg

nice set up !!

x's 2"thumbsup"

[ROCKCAD]

checked out the prototype 20* steering ...pretty nice set up ."thumbsup" should be a no brainer for the best steering kit when it gets dialed and hits production.8)"thumbsup"

[juan916]

any news on the 20degree steering

[flip2spin23]

x2 :mrgreen: looking good any time frame on the 20 degree yet

[CRAWLER DESIGN WORKS]

2-3weeks"thumbsup"

[treday619]

When are you going to have more of these available? I was not sure if it was 2 to 3 weeks on the clocked ones or all of them.

[tqcookie]

I am also interested in a 20* steering kit. Paypal ready.

[Big Bear]

I am also interested in a 20* steering kit. Paypal ready.
Same Here "thumbsup"

[XJ Farmer]

I'm in for the 20* if there is enough.

Thanks
Farmer

[Nova's Ark]

I am also interested in a 20* steering kit. Paypal ready.

[wojin]

put me on the list for the 20* setup