PDA

View Full Version : TJ-10 naked tranny pics!!!

DUDE
09-24-2004, 12:44 PM
Here you go for all those who I know have been waiting.
I have to fix it today for a little fun in Oregon Sat.
I broke something on the rear output so out it came.
I also am going from 113:1 to 95:1.
I think that is the mark, we will see. 8)

here it is shown with the bottom of the tlt chassie plate I removed and use for shims on the mounting. I only used the stock big screw location for mounting it in. The box end's of my chassie made it really rigged so that is all I need for mounting it and it works, easy teardown. 8)


http://img88.exs.cx/img88/8190/IMG_45.jpg
http://img88.exs.cx/img88/7237/IMG_46.jpg
http://img88.exs.cx/img88/8596/IMG_0032.jpg
http://img88.exs.cx/img88/2139/IMG_0033.jpg
http://img88.exs.cx/img88/9479/IMG_47.jpg
http://img88.exs.cx/img88/6171/IMG_48.jpg
DUDE
09-24-2004, 12:49 PM
I used 48 pitch gears with an hpi 96 tooth spur and a 12 tooth pinion with a stock Traxxes slipper set up.
I had it cranked tight and it never slipped. The carnage so far has been from hardcore use not an equimment issue. If it become's an equiment issue than I can adjust for that witth the slipper clutch.
It is like a hub "fuse" in 1:1. 8)

http://img88.exs.cx/img88/9320/IMG_49.jpg
Jim511
09-24-2004, 02:10 PM
Cool, thanks for the pictures and info! I noticed you were running a speed gems sapphire on dual gd600's. Now the sapphire just uses the pinion or whatever from the gd600 right? Im just wondering, as Im finally getting some TLT axles, and am going to be using M2K's, so I figured your truck would be a good idea to base mine off of, as you are running pretty much the same things as I will be.
DUDE
09-24-2004, 03:26 PM
Cool, thanks for the pictures and info! I noticed you were running a speed gems sapphire on dual gd600's. Now the sapphire just uses the pinion or whatever from the gd600 right? Im just wondering, as Im finally getting some TLT axles, and am going to be using M2K's, so I figured your truck would be a good idea to base mine off of, as you are running pretty much the same things as I will be.

With a proper fully adjustable 2 GD set up, you will have 3 pinions to manipulate the crwal ratio of your truck in more ways than you really want to think about. When I get it done I will post a spread sheet on the posability's. it's mind blowing. 8) 8)
TheNewbie
09-27-2004, 04:59 PM
Is this a stampede tranny?
DUDE
09-27-2004, 06:25 PM
Is this a stampede tranny?

Why yes it is, pede, rustler and bandit, they are all the same. The one in the pics is trimed down of the excess plastic I didn't need. 8)
smojoe
09-29-2004, 08:59 AM
Is it very difficult to install the stampede tranny in the stock chassis? I know you have to enlarge the hole for the spur and drill holes to secure the tranny, but is there anything else?
TRD
10-09-2004, 01:14 AM
DUDE I WOULD LIKE TO GET A GD 600 GEAR FROM YOU 'PM' ME SO I CAN GET YOUR INFO THANKS


TRD :twisted: