Rockpiledriver
05-13-2007, 05:03 PM
I got to try a set of the new Axial racing Rock Lizard tires for the first time yesterday, so I thought I would write a review. The first thing I noticed was, the compound is slightly softer than the Proline M2 and seems to have a more rubbery feel to it. Closer visual inspection revealed what I thought was a VERY cool feature of the rock Lizards. Every surface of the lugs is textured in the mold. It apperas that Axial media blasted only the lug areas of the mold, while maintaining a nice shiney surface on the rest of tire carcass. In other words the tires come pre-scuffed right out of the box. :shock:
The overall width of my rig changed from 10 1/4" with the Mashers to a narrower 10 1/8" with the Rock Lizards. The tire height also changed, the Lizards are another 1/8" taller than the Mashers.
The next interesting feature is the foams. The Axial foams are just slightly smaller than the OD of the tire. This is perfect in that it allows for a nice air gap between the foam and the tire surface, much like the Moab XL. The Axial foams are quite a bit softer than Proline foam. They also seem to made with more rubber content. Normally I use a bread knife when narrowing up foams to make a nice clean cut. The bread knife was no good on these foams. The rubber content of the foam grabbed at the knife making it difficult to get a clean cut. I switched to scissors to get the job done.
All I did was take just under 3/4" from the width of the stock foam, leaving just under 1 3/4" total width to use. This is what the tires look like all mounted up. You can see what I mentioned about the texture on the lugs in the pic.
http://img373.imageshack.us/img373/8971/lizardswc5.jpg
I figured the best place to test these would be on my rockpile, where I know exactly which lines I have, and have not made with other tires. As a control, I took the Hustler out with my Mashers mounted to the same wheels. The Mashers performed exactly as expected. They work very well and got me just about anywhere I needed to go.
Now it was the Rock Lizards turn. I drove right up the first obstacle with ease. Then I turned around into a severe off-camber section and had to really hold my line in order to keep the taller tires from causing the rig to fall off. The close proximity of the lugs, combined with the soft compound, got me through the section.
http://img299.imageshack.us/img299/6443/lizard2lc5.jpg
Next I climbed a spine that I was never able to make with Moabs. But I have been able to make with Mashers and wheel speed. Once I got lined up, the lizards went up it without having to bump the htrottle at all. There is a gap at the top of the climb that almost always swallows up Moabs, and sometimes Mashers. But the slight overall height of the Lizards let them walk right over it, and the lugs gripped the smooth rock clearing the obstacle with ease. One of the other REALLY cool features of the Lizards are the sound the make on the rock when searching for traction. Very close to a 1:1 tire.
http://img410.imageshack.us/img410/8656/lizard3ii7.jpg
Conclusion:
The Axial Racing 2.2 Rock Lizard tires are defiantely a force to be reckoned with. On my droop 2.2 rig, they work very well, so well I will definately give them a try at our next comp. "thumbsup"
The overall width of my rig changed from 10 1/4" with the Mashers to a narrower 10 1/8" with the Rock Lizards. The tire height also changed, the Lizards are another 1/8" taller than the Mashers.
The next interesting feature is the foams. The Axial foams are just slightly smaller than the OD of the tire. This is perfect in that it allows for a nice air gap between the foam and the tire surface, much like the Moab XL. The Axial foams are quite a bit softer than Proline foam. They also seem to made with more rubber content. Normally I use a bread knife when narrowing up foams to make a nice clean cut. The bread knife was no good on these foams. The rubber content of the foam grabbed at the knife making it difficult to get a clean cut. I switched to scissors to get the job done.
All I did was take just under 3/4" from the width of the stock foam, leaving just under 1 3/4" total width to use. This is what the tires look like all mounted up. You can see what I mentioned about the texture on the lugs in the pic.
http://img373.imageshack.us/img373/8971/lizardswc5.jpg
I figured the best place to test these would be on my rockpile, where I know exactly which lines I have, and have not made with other tires. As a control, I took the Hustler out with my Mashers mounted to the same wheels. The Mashers performed exactly as expected. They work very well and got me just about anywhere I needed to go.
Now it was the Rock Lizards turn. I drove right up the first obstacle with ease. Then I turned around into a severe off-camber section and had to really hold my line in order to keep the taller tires from causing the rig to fall off. The close proximity of the lugs, combined with the soft compound, got me through the section.
http://img299.imageshack.us/img299/6443/lizard2lc5.jpg
Next I climbed a spine that I was never able to make with Moabs. But I have been able to make with Mashers and wheel speed. Once I got lined up, the lizards went up it without having to bump the htrottle at all. There is a gap at the top of the climb that almost always swallows up Moabs, and sometimes Mashers. But the slight overall height of the Lizards let them walk right over it, and the lugs gripped the smooth rock clearing the obstacle with ease. One of the other REALLY cool features of the Lizards are the sound the make on the rock when searching for traction. Very close to a 1:1 tire.
http://img410.imageshack.us/img410/8656/lizard3ii7.jpg
Conclusion:
The Axial Racing 2.2 Rock Lizard tires are defiantely a force to be reckoned with. On my droop 2.2 rig, they work very well, so well I will definately give them a try at our next comp. "thumbsup"