My Shafty Tracer Nano

[danbillyboo]

I know, I know. I had a problem with my camera...

[danbillyboo]

Originally Posted by Duuuuuuuude

.

You do know that bodies have to be a minimum of 3" tall, right?

I know, but we didn't have a comp in my region . Thanks!

[danbillyboo]

Ok, I did a vid on the rock of my Shafty Nano. Look the last part in the vid.
My Shafty Tracer Nano V2 - YouTube
Thanks for watching!

[Hittman]

Very nice video! That last climb is sick

[danbillyboo]

Thanks!

[borybosell]

Originally Posted by danbillyboo

Hi everyone, this is my AX-10 with some change...
Spec :
- Futuba 4PL
- Tekin FX-R with handwound 35T
- Lipo 3S 1300 mha
- White HB Rover
- CC Bec
- 2 x Savox 1256TG
- VP Dig
- Axial BTA with C-Hub
- Delrin Home Made link
- Delrin Home Made Chassis
- Home made 1in Axial wheel

First, I cut my wheels to have a width of 1 inch.




I put a weight in the wheel and the beadlock ring hold the weight :


After, I bought Axial BTA and I put not 1, but 2 servo on axial plate (lots of torque...) :




I did my chassis. I want a shafty rig, but like a Berg Tracer Nano no suspension in front...




I have 4 inch of clearance


I centered the axis of the shaft to reduce torque twist and I put my dig's servo on the side with delrin protection.


I put a litle plate to protect my Lipo :



I protected my motor with plastic silicone tube :


With my Beetle body :



Look one this picture, my clearance about a Emaxx tire :


Thanks for your comments

I also have a AX-10 RC car, but there are some problems with it. Before 3 days it's one tire Is broken, I don't no that now what tire would be batter for it. I think this is good place to get one for it. So can you suggest me something mate? By the way nice job have been done by you over here.

[Colgout]

Originally Posted by obebaldone1

12 seconds. Come on man I need more..Looks awsome.

There are more..... Foudn some at the end of the video.

My Shafty Tracer Nano V2 - YouTube

Looking very good. Some of the climb is amazing.

[danbillyboo]

Thanks! I like this crawler!


Sent from my iPhone using Tapatalk

[ManxCrawler]

Gotta say that vert right at the end was impressive for a shafty

[danbillyboo]

Thanks! I would like to comp against a crawler MOA, but we have no comp in our region.

[danbillyboo]

Ok some change of my Shafty Tracer Nano.
First, I liked my two servos setup, but, it was to weight and servos are too high to get a good COG. I took the decision to remove a servo and make a support for one servo.


Assembly in axle :


After, I did a same plate for Lipo :



Next, I did a new frame with Carbone plate :

I wanted to reduce the weight of my frame. The weight of my delrin frame :

The new one with Carbone plate 1.5mm thickness. :

[danbillyboo]

After that, I changed my axial wheels for Vanquish wheels SLW et DH II

And new servo Savox SA-1283SG.

My old body was broken. I changed it :






With my Monster Beetle SCX-10 :

[danbillyboo]

New weight 4 lbs 11 oz:

[Blades]

Love the crib with the Tonka truck in it..LOL. Looks sweet with the new body

[danbillyboo]

LOL my boy put his truck in it to vex my daughter. LOL

[ICRAWLEDIT]

awesome i like the double servos, for savox the 58TG is really fast and tones of torque just sayin but i bet you have no issues.

VERSION RC
WWW.YOUTUBE.COM/YOURBESTVERSION

[danbillyboo]

Thanks !!


Sent from my iPhone using Tapatalk

[danbillyboo]

Ok some update :
I installed Delrin Wide Tube from Creation Fab.

http://www.rccrawler.com/forum/axles...ml#post3645410


After, I installed Wraith's Chubs:


And I cut a two arms on Wraith's knuckles. Because I don't need it.
Before :


After :


And I installed it with XR-10 Universal shafts :


The results :



With the home made servo links :


I like it !

[danbillyboo]

Ok after it, I think my rig need some clean up...


I smashed my électronique.
RX :

BEC :

And Tekin FXR.

I assembly it :


In the rig :

[danbillyboo]

I changed my Delrin link per vanquish Titanium links. I did the same shape of my old Delrin link :


After, I installed it. Look nice et more strong :



Thanks !