XR10 Mod for AX10 Axles Parts List I’ve been asked several times lately for a list of required and recommended parts for the XR10 modification to the AX10 axles so I decided to write up a list. This thread will include part numbers and some RCC vendors who carry them. It will also have my recommendations on what to use. These recommendations are purely my opinion and can be replaced with your favorite brand of hop-up parts. RCC Vendors That Carry Some or All of These Parts Vanquish Products Crawler Innovations TCS RCP Crawlers RPP Hobby Required XR10 Parts 1. XR10 Universals – AXI30563 2. XR10 Straight Axles – AXI30758 (You will need two of the 110mm shafts so either order two of this part or cut and grind the longer 117mm shaft.) 3. XR10 Knuckles – AXI80061 ( I prefer Vanquish Incision Knuckles) 4. XR10 C-Hubs – AXI80062 (I prefer Vanquish Incision C-Hubs) 5. XR10 Lockouts – AXI80064 (I prefer Vanquish Incision Lockouts) Beef Tube Options 1. Biggin69 (Longer Beef Tubes) 2. Chris_The_Battery_Man (Wide Splined – Front)(Wide Un-Splined – Rear) Hardware Needed (Note: Your hop-up parts may include hardware.) 1. M3x6mm Button Head x 24 (Beef Tube and C-Hub Installation) 2. M3x8mm Button Head x 8 (Knuckle and Lockout Installation) Other Recommended Parts 1. Your favorite brand of locker/spool. 2. Under Drive Rear Gear Set (43/13) – AXI30402 3. Over Drive Front Gear Set (36/14) – AXI30401 I hope this helps someone. If there is any interest I can also post a list of parts needed for building axles and a transmission from scratch. If you have any questions shoot me a PM "thumbsup" Link to my 2.2S |
Right on! This will be great to have for my new build I am putting together. Thanks! |
Re: XR10 Mod for AX10 Axles Parts List Good to know! I actually like the trac width offset. |
Re: XR10 Mod for AX10 Axles Parts List Never mind, I was wrong. I did use XR's and 2 short sides. Lol. My bad |
Re: XR10 Mod for AX10 Axles Parts List Lol it's all good... But on the track width subject I usually make up for it in hub sizes anyway. |
Re: XR10 Mod for AX10 Axles Parts List Thanks for the info brother! |
Re: XR10 Mod for AX10 Axles Parts List I've ordered about 85% of the parts. Thanks for your help. |
Re: XR10 Mod for AX10 Axles Parts List No problem fellas "thumbsup" |
Re: XR10 Mod for AX10 Axles Parts List Also on Knuckle, the VP one is Zero ankerman but not Axial one. I think well worth the extra money. For C-hub, I uses TopCAD one, mate up with Vp knuckle no problem and only 1/3 the price. |
Re: XR10 Mod for AX10 Axles Parts List i did this mod WITHOUT the beef tubes. very easy to do. i used strc c-hubs with vp knuckles. the vp knuckles are a little different and allow more steering angle. i did not swap the rear axle shafts since i don't see the point in that. mine was done cheaply with cut down xr universals, c-hubs, knuckles. that was it. |
Re: XR10 Mod for AX10 Axles Parts List Great info Chris! |
Re: XR10 Mod for AX10 Axles Parts List I did mine with chris the batterymans short splined tubes with vanquish chubs an stock xr knuckles with cut down xr universals an overdrive gears, I wanted to be just a 1/2 wider than the stock width,this was the ticket! awsome write up on the info"thumbsup" |
Re: XR10 Mod for AX10 Axles Parts List Quote:
|
Re: XR10 Mod for AX10 Axles Parts List Great post Kent. Another option for rear axle shafts are the Wheely King axle shafts. They are a direct drop in with "longer beef tubes". No issues with mine in over 6 months of comps. HPI Wheely King Straight Axle http://www.rccrawler.com/forum/axial...ml#post3393771 post #50 I have since replaced the spacers with e-clips to hold the axle in. |
Re: XR10 Mod for AX10 Axles Parts List Great thread, it should be a sticky. "thumbsup" |
Re: XR10 Mod for AX10 Axles Parts List Subscribed Kent"thumbsup". It was nice to meet you last weekend and I look forward to seeing this build come together. |
Re: XR10 Mod for AX10 Axles Parts List Thanks guys! It was my goal when I posted this to get as much info on this mod in one place as possible. Once I start my build thread I will post a link to it in the original post. |
Re: XR10 Mod for AX10 Axles Parts List Heres instructions and purchase info on my delrin tubes: http://www.rccrawler.com/forum/axles...ml#post3648912 |
Re: XR10 Mod for AX10 Axles Parts List Quote:
|
Re: XR10 Mod for AX10 Axles Parts List yeah those work well I have them on mine |
All times are GMT -6. The time now is 09:35 PM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com