Go Back   RCCrawler Forums > RCCrawler Brand Specific Tech > Heritage Crawlers > Axial AX-10 Scorpion
Loading

Notices

Thread: XR10 Mod for AX10 Axles Parts List

Reply
 
LinkBack Thread Tools Display Modes
Old 05-24-2012, 03:48 PM   #1
Quarry Creeper
 
Join Date: Nov 2009
Location: Central Arkansas
Posts: 309
Default XR10 Mod for AX10 Axles Parts List

I’ve been asked several times lately for a list of required and recommended parts for the XR10 modification to the AX10 axles so I decided to write up a list. This thread will include part numbers and some RCC vendors who carry them. It will also have my recommendations on what to use. These recommendations are purely my opinion and can be replaced with your favorite brand of hop-up parts.

RCC Vendors That Carry Some or All of These Parts
Vanquish Products
Crawler Innovations
TCS
RCP Crawlers
RPP Hobby

Required XR10 Parts
1. XR10 Universals – AXI30563
2. XR10 Straight Axles – AXI30758 (You will need two of the 110mm shafts so either order two of this part or cut and grind the longer 117mm shaft.)
3. XR10 Knuckles – AXI80061 ( I prefer Vanquish Incision Knuckles)
4. XR10 C-Hubs – AXI80062 (I prefer Vanquish Incision C-Hubs)
5. XR10 Lockouts – AXI80064 (I prefer Vanquish Incision Lockouts)

Beef Tube Options
1. Biggin69 (Longer Beef Tubes)
2. Chris_The_Battery_Man (Wide Splined – Front)(Wide Un-Splined – Rear)

Hardware Needed (Note: Your hop-up parts may include hardware.)
1. M3x6mm Button Head x 24 (Beef Tube and C-Hub Installation)
2. M3x8mm Button Head x 8 (Knuckle and Lockout Installation)

Other Recommended Parts
1. Your favorite brand of locker/spool.
2. Under Drive Rear Gear Set (43/13) – AXI30402
3. Over Drive Front Gear Set (36/14) – AXI30401

I hope this helps someone. If there is any interest I can also post a list of parts needed for building axles and a transmission from scratch. If you have any questions shoot me a PM

Link to my 2.2S

Last edited by WooPigSooie; 08-09-2012 at 01:19 AM.
WooPigSooie is offline   Reply With Quote
Sponsored Links
Old 05-24-2012, 04:18 PM   #2
Rock Crawler
 
Join Date: Dec 2009
Location: Redding
Posts: 705
Default

Right on! This will be great to have for my new build I am putting together. Thanks!
Propane is offline   Reply With Quote
Old 05-24-2012, 05:38 PM   #3
Quarry Creeper
 
Join Date: Nov 2009
Location: Central Arkansas
Posts: 309
Default Re: XR10 Mod for AX10 Axles Parts List

Good to know! I actually like the trac width offset.
WooPigSooie is offline   Reply With Quote
Old 05-24-2012, 06:17 PM   #4
TSK
Shelf queen
 
TSK's Avatar
 
Join Date: Aug 2008
Location: Internet
Posts: 5,857
Default Re: XR10 Mod for AX10 Axles Parts List

Never mind, I was wrong. I did use XR's and 2 short sides. Lol. My bad

Last edited by TSK; 05-24-2012 at 06:21 PM.
TSK is offline   Reply With Quote
Old 05-24-2012, 06:41 PM   #5
Quarry Creeper
 
Join Date: Nov 2009
Location: Central Arkansas
Posts: 309
Default Re: XR10 Mod for AX10 Axles Parts List

Lol it's all good...

But on the track width subject I usually make up for it in hub sizes anyway.
WooPigSooie is offline   Reply With Quote
Old 05-24-2012, 07:23 PM   #6
Quarry Creeper
 
Join Date: Dec 2008
Location: Santa Mira
Posts: 341
Default Re: XR10 Mod for AX10 Axles Parts List

Thanks for the info brother!
MexicanMarauder is offline   Reply With Quote
Old 05-24-2012, 07:29 PM   #7
Rock Crawler
 
Join Date: Jul 2011
Location: north little rock
Posts: 979
Default Re: XR10 Mod for AX10 Axles Parts List

I've ordered about 85% of the parts. Thanks for your help.
mmatthews is offline   Reply With Quote
Old 05-24-2012, 08:28 PM   #8
Quarry Creeper
 
Join Date: Nov 2009
Location: Central Arkansas
Posts: 309
Default Re: XR10 Mod for AX10 Axles Parts List

No problem fellas
WooPigSooie is offline   Reply With Quote
Old 05-24-2012, 08:54 PM   #9
Rock Crawler
 
Join Date: Aug 2011
Location: Perth west oz
Posts: 944
Default Re: XR10 Mod for AX10 Axles Parts List

Also on Knuckle, the VP one is Zero ankerman but not Axial one. I think well worth the extra money. For C-hub, I uses TopCAD one, mate up with Vp knuckle no problem and only 1/3 the price.
Colgout is offline   Reply With Quote
Old 05-24-2012, 09:37 PM   #10
Rock Crawler
 
Join Date: Nov 2009
Location: poteau
Posts: 996
Default Re: XR10 Mod for AX10 Axles Parts List

i did this mod WITHOUT the beef tubes. very easy to do. i used strc c-hubs with vp knuckles. the vp knuckles are a little different and allow more steering angle. i did not swap the rear axle shafts since i don't see the point in that. mine was done cheaply with cut down xr universals, c-hubs, knuckles. that was it.
hoghead5150 is offline   Reply With Quote
Old 05-24-2012, 10:08 PM   #11
Quarry Creeper
 
Join Date: Nov 2009
Location: Central Arkansas
Posts: 309
Default Re: XR10 Mod for AX10 Axles Parts List

Great info Chris!
WooPigSooie is offline   Reply With Quote
Old 05-25-2012, 06:50 AM   #12
Quarry Creeper
 
Join Date: Apr 2008
Location: SHADYSIDE
Posts: 294
Default Re: XR10 Mod for AX10 Axles Parts List

I did mine with chris the batterymans short splined tubes with vanquish chubs an stock xr knuckles with cut down xr universals an overdrive gears, I wanted to be just a 1/2 wider than the stock width,this was the ticket! awsome write up on the info
crawlernut is offline   Reply With Quote
Old 05-25-2012, 07:25 AM   #13
No idea what I'm doing
 
Join Date: Oct 2008
Location: Underground, CO
Posts: 4,529
Default Re: XR10 Mod for AX10 Axles Parts List

Quote:
Originally Posted by hoghead5150 View Post
i did this mod WITHOUT the beef tubes. very easy to do. i used strc c-hubs with vp knuckles. the vp knuckles are a little different and allow more steering angle. i did not swap the rear axle shafts since i don't see the point in that. mine was done cheaply with cut down xr universals, c-hubs, knuckles. that was it.
I did mine the same way, but this is a fantastic post! With the popularity of this mod, this should be stickied.
C*H*U*D is offline   Reply With Quote
Old 05-25-2012, 07:34 AM   #14
I wanna be Dave
 
Join Date: Oct 2007
Location: Castle Rock, WA
Posts: 8,761
Default Re: XR10 Mod for AX10 Axles Parts List

Great post Kent.

Another option for rear axle shafts are the Wheely King axle shafts. They are a direct drop in with "longer beef tubes".
No issues with mine in over 6 months of comps.

HPI Wheely King Straight Axle

Szczerba's FF-SZ 2.2s post #50
I have since replaced the spacers with e-clips to hold the axle in.
Szczerba is offline   Reply With Quote
Old 05-25-2012, 07:40 AM   #15
I wanna be Dave
 
Join Date: May 2007
Location: Taylors Falls just hanging with the MNRCRC crew.
Posts: 7,840
Default Re: XR10 Mod for AX10 Axles Parts List

Great thread, it should be a sticky.
Stormin2u is offline   Reply With Quote
Old 05-25-2012, 07:44 AM   #16
Tire&Foam Extraordinaire
 
Nova's Ark's Avatar
 
Join Date: Jun 2007
Location: C.I. Compound, Tyler, Texas
Posts: 5,568
Default Re: XR10 Mod for AX10 Axles Parts List

Subscribed Kent. It was nice to meet you last weekend and I look forward to seeing this build come together.
Nova's Ark is offline   Reply With Quote
Old 05-25-2012, 09:01 AM   #17
Quarry Creeper
 
Join Date: Nov 2009
Location: Central Arkansas
Posts: 309
Default Re: XR10 Mod for AX10 Axles Parts List

Thanks guys!

It was my goal when I posted this to get as much info on this mod in one place as possible.

Once I start my build thread I will post a link to it in the original post.
WooPigSooie is offline   Reply With Quote
Old 05-25-2012, 11:30 AM   #18
I wanna be Dave
 
Chris_The_Battery_Man's Avatar
 
Join Date: Oct 2006
Location: Milwaukie OR
Posts: 2,079
Default Re: XR10 Mod for AX10 Axles Parts List

Heres instructions and purchase info on my delrin tubes:

http://www.rccrawler.com/forum/axles...ml#post3648912
Chris_The_Battery_Man is offline   Reply With Quote
Old 05-25-2012, 03:01 PM   #19
Pebble Pounder
 
Join Date: Jan 2010
Location: League City
Posts: 139
Default Re: XR10 Mod for AX10 Axles Parts List

Quote:
Originally Posted by Colgout View Post
Also on Knuckle, the VP one is Zero ankerman but not Axial one.
AXIAL Sells zero ackerman steering plates ax30778 that should fit the stock knuckle.
RCOG is offline   Reply With Quote
Old 05-27-2012, 05:12 PM   #20
Quarry Creeper
 
Join Date: Nov 2009
Location: Central Arkansas
Posts: 309
Default Re: XR10 Mod for AX10 Axles Parts List

yeah those work well I have them on mine
WooPigSooie is offline   Reply With Quote
Reply



XR10 Mod for AX10 Axles Parts List - Similar Threads
Thread Thread Starter Forum Replies Last Post
newbie need help parts list for overdrive mod on mrc pro hammer29 Losi Mini-Rock Crawler 22 06-21-2015 02:20 PM
Axial parts list for scratch XR10 build? jubilee Axial XR10 7 04-11-2012 08:42 PM
X-Factor axles - PARTS LIST!!! cman_1500w XTM Crawler 15 10-24-2004 11:44 PM
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -6. The time now is 08:17 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2022, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com