Re: Gerry´s SuDu One FL - CF Axle <3lb Shafty These axles look amazing... But can you drive??:twisted::twisted: |
Re: Gerry´s SuDu One FL - CF Axle <3lb Shafty Quote:
Quote:
Ok, the roller is done - lower links are made from Ti, the upper links are made of CF: http://www.rccrawler.at/board/index....chmentID=15375 http://www.rccrawler.at/board/index....chmentID=15376 http://www.rccrawler.at/board/index....chmentID=15377 And the overall weight of the roller incl. the servo: http://www.rccrawler.at/board/index....chmentID=15378 968g are about 2.13lb - not bad i think "thumbsup" |
Top job mate :) Sent from my GT-I9300 using Tapatalk |
Re: Gerry´s SuDu One FL - CF Axle <3lb Shafty Are you planning to run the servo without the bottom case like that? Front upper link geometry looks a little crazy. Seems like simply driving forward will squat the chassis down until the shocks bottom out. Good progress, otherwise. |
Re: Gerry´s SuDu One FL - CF Axle <3lb Shafty Hi, I am not convinced… if you add the weight of various of missing elements : motor 300g (10.5oz) + liPo 100g (3.5oz) + ESC + Bec 150g (5.3oz) + body 100g (3.5oz) + paint for body 30g (1 oz) + wire 80g (2.8oz) + and what I forget 50g (1.8oz) = 1780g (3lbr 14.8oz). it's largely more than the 3lbs envisaged :roll: You will have to stop… :flipoff: F***ing nice work!! |
Re: Gerry´s SuDu One FL - CF Axle <3lb Shafty Quote:
You need to check your weight estimates, Steph! Motor is max 175g, lipo is 50g, ESC and BEC are probably much less than 150g etc. |
Re: Gerry´s SuDu One FL - CF Axle <3lb Shafty Couldn't agree more Tomi My puller 500 is only 4.3oz no where near 10.5 :shock: Battery 2oz Esc/bec 2.5oz with wire Body 1oz 9oz is what I see being added plus whatever knuckle weight Which I don't see much being needed on this amazing rig So yes it will be over 3lbs but who care what he did here is just awesome |
Re: Gerry´s SuDu One FL - CF Axle <3lb Shafty Nah, I can still see this coming in at just under 3 lbs even with an ounce each side for knuckle weights. Time will tell. |
Re: Gerry´s SuDu One FL - CF Axle <3lb Shafty It´s happened! The roller is now full electrified and RTR 8) http://www.rccrawler.at/board/index....chmentID=15398 And now, let us check the weight from the RTR rig: http://www.rccrawler.at/board/index....chmentID=15395 http://www.rccrawler.at/board/index....chmentID=15396 I would say - goal reached :twisted:"thumbsup" But for sure, if i add some knuckleweights (and i´m sure i would) - maybe i´m over the 3lb - but that´s not important any more "thumbsup" I hope i can test tomorrow the Shafty, if all will work fine i will shorten the wires and will post up some pics of all the details! In the front i have to use a bit longer shocks, then also the upper front links will fit how the should "thumbsup" I´m so happy! |
Top job Gerry. Great to see the mix of NCD snd your own creation. Goes together like it was ment to be. Cant wait to see this in action. Im sure there are many guys who will want your axels not to mention the guys already using their NCD SuDu's Sent from my GT-I9300 using Tapatalk |
Re: Gerry´s SuDu One FL - CF Axle <3lb Shafty @ Tomy, chevotafun and Oz Bruiser I had hoped that the nonsense of the weights that I announced (like 30g - 1 oz for paint for body or 80g - 2.8oz for wire), would be understood like humor.@ Gerry I quote my last post |
Re: Gerry´s SuDu One FL - CF Axle <3lb Shafty That is a gorgeous quality build. Very professional looking. Two thumbs up |
Very nice mate :D Sent from my GT-I9505 using Tapatalk |
Re: Gerry´s SuDu One FL - CF Axle <3lb Shafty It's alive! |
Re: Gerry´s SuDu One FL - CF Axle <3lb Shafty Looking great Gerry! Nice an light. Perfect setup IMO.. Light rig, then add weight where you need it. I can't wait to see more, and hear how it runs"thumbsup" |
Re: Gerry´s SuDu One FL - CF Axle <3lb Shafty Congrats! |
Re: Gerry´s SuDu One FL - CF Axle <3lb Shafty I think that rig is to light for the 2.2S Class. You have to start at 1.9:mrgreen: ...but normally it's not a to bad work on these;-) Hope to see you soon on the rocks"thumbsup" |
Re: Gerry´s SuDu One FL - CF Axle <3lb Shafty Hi, I now even could see it in Action - amazing. And here is the "proof". https://dl.dropboxusercontent.com/u/...2017.45.04.jpg More Details shall be provided by the builder ;) Cheers Daniel |
Re: Gerry´s SuDu One FL - CF Axle <3lb Shafty Quote:
|
Re: Gerry´s SuDu One FL - CF Axle <3lb Shafty Looking great Gerry "thumbsup" Absolutely the next level :twisted: @Totorax: I got your humor first time I read it ... nice one :mrgreen:"thumbsup" Thanks Tomi :mrgreen: |
All times are GMT -6. The time now is 11:49 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com