01-08-2016, 12:12 PM | #1 |
Pebble Pounder Join Date: Jan 2016 Location: Athens
Posts: 156
| Nburns11 BWD nightmare
Nburns11 bulld First off this is my first build thread and I'm super excited, first built not bought. I will be building a billet works design nightmare cf kit. I have been eyeing this chassis down for a few months and couldn't dare leave my scaler. Well I did it parted my scx10 all the way down to transmission plate to ladder rails. Parts started selling left and right, finally I had enough to order my chassis so messaged I don through Facebook (thanks your an awesome human being) and placed my order 1/7/15. Now I wait for the chassis to be fabbed and shipped to me but in the mean time I have been following papas build very closely I'm gonna be using a lot of the same parts he has used. I also took a lot of my questions to the Facebook groups. So let's begin :::: Parts list :::: •Chassis• BWD Carbon Nightmare kit w/Links ** GTR ball ends ** Revo ball ends ** •Shocks• Big bore Shocks ** Losi mini t springs ** Losi mini t springs ** Jeepin Dougs T-cups ** Shock mod GTR rod ends ** •tranny• Classicutcustoms.com bulldog transmission WB8-HD driveshafts ** •Axles• ~Front Axial axle housing ** GribFab SS lockers ** VP wraith knuckles ** VP wraith chubs** Beef tubes wide steering kit ** Axial Overdrive gears ** Axial xr10 universals ** Aluminum splined beef tubes ~Rear Axial axle housing ** Wraith Lockouts went back to plastic Rear Axles ** GribFab SS lockers ** axial stock gears ** Axial underdrive gears •Electronics• Holmes hobbies BR mini pro ** Holmes Hobbies Puller 500 13.5t ** Hitec 7980 ** - received in the mail/part in possession/part ordered Disclaimer : see a problem with my parts list let me know Shout out to Classicutcustoms for the lockouts and axles . huge shoutout to Don over at billet works designs he has helped me throughout this whole build and also papabash your Always there to answer questions and I appreciate that dude . Last edited by Nburns11; 08-01-2016 at 12:41 AM. Reason: Build a better thread |
Sponsored Links | |
01-08-2016, 08:29 PM | #2 |
Pebble Pounder Join Date: Jan 2016 Location: Athens
Posts: 156
| Nburns11 BWD nightmare
1/12/16 I went ahead and dropped a few grams on the receiver . 1/15/16 Received the other set of big bores and jeepin dougs t-cups today Went ahead and assembled them. Last edited by Nburns11; 02-03-2016 at 04:55 PM. |
01-08-2016, 08:30 PM | #3 |
Pebble Pounder Join Date: Jan 2016 Location: Athens
Posts: 156
| Nburns11 BWD nightmare
Reserved
Last edited by Nburns11; 02-03-2016 at 04:56 PM. |
01-18-2016, 10:21 PM | #4 |
Quarry Creeper Join Date: Dec 2008 Location: Alabama
Posts: 260
| Re: Nburns11 BWD nightmare
Space reserved for comments when you get everything. Lol.
|
01-19-2016, 05:36 PM | #5 |
Pebble Pounder Join Date: Jan 2016 Location: Athens
Posts: 156
| Re: Nburns11 BWD nightmare |
02-01-2016, 11:39 AM | #6 |
Quarry Creeper Join Date: Nov 2012 Location: Blue Ridge
Posts: 332
| Re: Nburns11 BWD nightmare
Alright, get those wrenches turning and pics taken lol
|
02-01-2016, 01:37 PM | #7 |
Pebble Pounder Join Date: Jan 2016 Location: Athens
Posts: 156
| Re: Nburns11 BWD nightmare
Well here we go . wrenches are turning pics as I go . Sent from my iPhone using Tapatalk |
02-01-2016, 02:46 PM | #8 |
Pebble Pounder Join Date: Jan 2016 Location: Athens
Posts: 156
| Nburns11 BWD nightmare
Went ahead assembled the tranny with dons new 1 of 3 carbon motor plates I think papa don and I are the only ones with this mount right now and I will say I'm just amazed by how great this looks . Sent from my iPhone using Tapatalk Last edited by Nburns11; 02-02-2016 at 07:17 AM. |
02-01-2016, 03:16 PM | #9 |
I wanna be Dave Join Date: Jun 2007 Location: Earth
Posts: 2,488
| Re: Nburns11 BWD nightmare
is this thing done yet? Glad to see you're getting her put together...even though you're supposed to be moving today |
02-01-2016, 06:43 PM | #10 |
E.Y. Designs Join Date: Sep 2011 Location: Springfield, OR
Posts: 3,591
| Re: Nburns11 BWD nightmare |
02-01-2016, 07:09 PM | #11 |
Pebble Pounder Join Date: Jan 2016 Location: Athens
Posts: 156
| Re: Nburns11 BWD nightmare |
02-01-2016, 07:11 PM | #12 |
Pebble Pounder Join Date: Jan 2016 Location: Athens
Posts: 156
| Nburns11 BWD nightmare Ran into a bind with the transmission it had a longer top shaft then my other transmission so I stole the shaft switched those around put me behind by like 45 minutes had to take a break and go run a errand . But this is where I am so far. I'll eventually get the slipper clutch eliminator from lockedup Rc Sent from my iPhone using Tapatalk Last edited by Nburns11; 02-03-2016 at 08:53 PM. |
02-01-2016, 08:09 PM | #13 |
Quarry Creeper Join Date: Nov 2012 Location: Blue Ridge
Posts: 332
| Re: Nburns11 BWD nightmare
Hell yea, that cf is mesmerizing. looking good
|
02-02-2016, 12:42 AM | #14 |
Pebble Pounder Join Date: Jan 2016 Location: Athens
Posts: 156
| Nburns11 BWD nightmare
I assembled the chassis, links and got almost everything done that I could. Went to our new house got the key today. And my wife's car key broke no way to go or anything so we booked a Uber transportation back to our hotel where the spare was and my build so after a 2 hour delay I got back to my build and ended up here for the night it's 2:30 in the morning time to get some sleep . tomorrow Is the shock cap mod. Remind you I'm still waiting on a lot of parts . Mostly for the axles so far I'm pretty damn happy with this build. Very happy with the carbon fiber. Sent from my iPhone using Tapatalk Last edited by Nburns11; 02-03-2016 at 04:58 PM. |
02-02-2016, 03:10 PM | #15 |
Quarry Creeper Join Date: Jun 2011 Location: panama city
Posts: 296
| Re: Nburns11 BWD nightmare
Good looking build bro. This is Doug from pc monster rc Sent from my SCH-S968C using Tapatalk |
02-02-2016, 03:24 PM | #16 | |
Pebble Pounder Join Date: Jan 2016 Location: Athens
Posts: 156
| Re: Nburns11 BWD nightmare Quote:
Thanks doug you coming to the moss rock meet March 6th ? It's been a fun one that's for sure I'm kinda at a stand still atm until more parts show up Sent from my iPhone using Tapatalk | |
02-02-2016, 03:25 PM | #17 |
Quarry Creeper Join Date: Jun 2011 Location: panama city
Posts: 296
| Re: Nburns11 BWD nightmare
I'd it on Birmingham Sent from my SCH-S968C using Tapatalk |
02-02-2016, 06:20 PM | #18 |
Pebble Pounder Join Date: Jan 2016 Location: Athens
Posts: 156
| Nburns11 BWD nightmare
2/2/2016 - only thing I could do today was the traxxas shock cap mod. I've got two done one is drying right now (silicon sealant) I'll get the rest done tonight and mounted back on the truck and I'll call it a night Well stayed up a little longer and got the bec soldered up the HH BR MINI PRO. When it's time to mount to the chassis I'll probably shorten 3pin connectors wires to the receiver to give it a real clean install Sent from my iPhone using Tapatalk Last edited by Nburns11; 02-02-2016 at 11:14 PM. |
02-03-2016, 05:02 PM | #19 |
Pebble Pounder Join Date: Jan 2016 Location: Athens
Posts: 156
| Nburns11 BWD nightmare
Got my Grip Fab SS lockers In today. Got them assembled using a HD overdrive gear for the front. And a left over stock gear for the rear. I'm waiting on my bearing kit to get these rear axles done. Now I'm waiting on my Rc stimulus package (income tax) to come into the back account to order a few more parts that I need . More updates coming after dinner time. Went ahead and mounted up the front axle with the servo/battery mount. I'll have to pull the axle housing and install its guts as the parts show up. And I'm calling it a night probably won't have any updates till Monday cause we will be moving this weekend Sent from my iPhone using Tapatalk Last edited by Nburns11; 02-03-2016 at 09:00 PM. |
02-08-2016, 07:10 PM | #20 |
Quarry Creeper Join Date: Nov 2012 Location: Blue Ridge
Posts: 332
| Re: Nburns11 BWD nightmare
Looking sweet man
|
Nburns11 BWD nightmare - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Papa's BWD Nightmare S | papabash | Axial AX-10 Scorpion | 392 | 11-26-2018 04:22 AM |
A nightmare on purp street ... Bwd shafty | Purptr8r | Axial AX-10 Scorpion | 104 | 03-27-2015 05:47 AM |
Kratos Bwd "Nightmare" build | Kratos | Axial XR10 | 31 | 06-10-2013 03:24 PM |
| |