Little Winner, gettin UN-Stuck..

[cliff1119]

Looks like someone is snooping

[winnerone23]

Originally Posted by cliff1119

Looks like someone is snooping

Boy, are you crazy!?
You can't wear antlers in the woods, around here, during hunting season.. you'll get shot!

[roksloski]

you dont need the lockedup kit, axial makes a shaft for about 6 bucks, and you you use the stock backing plate that comes with every tranny case set.......

you save 14 bucks

the lockedup one is nice though..........

[snapon boy]

Ok, roksolski those are good ideas but what is the part number for the spacer that goes behind the spur gear backing plate so it dosnt slide in to far.

149 r/c worx team driver

[winnerone23]

Originally Posted by roksloski

you dont need the lockedup kit, axial makes a shaft for about 6 bucks, and you you use the stock backing plate that comes with every tranny case set.......

you save 14 bucks

the lockedup one is nice though..........

Originally Posted by snapon boy

Ok, robloski those are good ideas but what is the part number for the spacer that goes behind the spur gear backing plate so it dosnt slide in to far.

149 r/c worx team driver

Did I miss a post? What info is this regarding?
Lol..

[snapon boy]

I think roksolski did, or the fourm jumped a page. Sorry troy

149 r/c worx team driver

[winnerone23]

Originally Posted by snapon boy

I think rob did, or the fourm jumped a page. Sorry troy

149 r/c worx team driver

No problem.. I will have to look back, closer.
Half asleep.. with a wrench in hand.. lol..

[roksloski]

Originally Posted by winnerone23

Did I miss a post? What info is this regarding?
Lol..

Post #1 - Picture #3..........



Really Snaponboy, google search, or the ax10 manual....

Part #ax30197
ax30162
ax30484
ax39489

i will let you do the search to find out what part no.# is what........

[snapon boy]

I guess thank you is in order, thank you roksolski ! I have all of those parts I was thinking I was missing something guess not.

149 r/c worx team driver

[roksloski]

Originally Posted by snapon boy

I guess thank you is in order, thank you rob! I have all of those parts I was thinking I was missing something guess not.

149 r/c worx team driver

who's rob?........................... not me....

[snapon boy]

Ok I goofed, and I changed my goof. Sorry

149 r/c worx team driver

[WHITE-TRASH]

The plastic axial slipper eliminator will hold up for a while before it ends up with a nice round 5mm hole. I killed 2 of them before getting a locked up rc metal version. The input shaft for the transmission is the same between the factory non slipper and locked up version. It would be nice if someone simply sold an alloy slipper eliminator piece instead of swapping the whole shaft etc.

[winnerone23]

Originally Posted by roksloski

Post #1 - Picture #3............

Oh oh, cause I days about a locked slipper..

I'll just end up with a comp tranny.. hopefully a Robbob(this is Rob)/ Krazed Builds tranny!

Or I'll make a bulldog trans, work..

[Robbob]

Originally Posted by winnerone23

I'll just end up with a comp tranny.. hopefully a Robbob(this is Rob)/ Krazed Builds tranny!

Or I'll make a bulldog trans, work..

Cleaning the dust off that project once we get back from NENC

[roksloski]

Originally Posted by WHITE-TRASH

It would be nice if someone simply sold an alloy slipper eliminator piece instead of swapping the whole shaft etc.

They Do.......

GPM has one.........


and it uses the shaft you already have that has the 2 holes....

[WHITE-TRASH]

Originally Posted by roksloski

They Do.......

GPM has one.........


and it uses the shaft you already you have that has the 2 holes....

Well go figure.

https://www.gpmparts.com/axial-racin...-90068905.html

Thanks for the heads up.

[roksloski]

this is what the GPM kit looks like put together.....
in a scaler its fine......
but in a sporty, if tou have a cross brace ,like my sporty does, this wont work because of the longer shaft...............



with the short axial shaft, or the lockedup shaft the nylok nut is much closer to the spur gear........
just an FYI

[Robbob]

The un-Stuck was designed around not using a slipper ...... you wanna use the shorter shaft

[winnerone23]

I'm stuck with a long shaft... and it works fine.. ;)

[VMGontheRocks]

Originally Posted by Robbob

The un-Stuck was designed around not using a slipper ...... you wanna use the shorter shaft

Slippers... are those the things you wear around the house...