Little Winner, gettin UN-Stuck..
 

Plain and simple!
A couple pieces of CF and a delrin skid..
http://uploads.tapatalk-cdn.com/2016...1ccad21e7c.jpg
Comes nicely packaged..
http://uploads.tapatalk-cdn.com/2016...cc951e7cee.jpg
I got straight to work... (A week later) [emoji33]

Hmmm.. Might have to lose the slipper and upgrade to a locked setup..(instead of a locked slipper)
http://uploads.tapatalk-cdn.com/2016...82c0e58a4a.jpg
Or not....
http://uploads.tapatalk-cdn.com/2016...05b09cfdec.jpg
Some Sweet braces, I've had, from BmachineRC!
http://uploads.tapatalk-cdn.com/2016...c3b8279137.jpg
Time to get to work on some links!
http://uploads.tapatalk-cdn.com/2016...c13ac611c6.jpg
A nice fresh rear link mount..
http://uploads.tapatalk-cdn.com/2016...5f9e05d2b9.jpg
And of course.....

A CustomFiber desTroy plate! [emoji106] [emoji38]
http://uploads.tapatalk-cdn.com/2016...5383a1b56a.jpg

Re: Little Winner, gettin UN-Stuck..
 

Nice!![emoji106] Love that CF bling


Sent from my iPhone using Tapatalk

Re: Little Winner, gettin UN-Stuck..
 

The Bmachine braces look cool on there too

Re: Little Winner, gettin UN-Stuck..
 

Waiting on some actual width one's, now! [emoji41]

Re: Little Winner, gettin UN-Stuck..
 

Let's get a little update going on..
http://uploads.tapatalk-cdn.com/2016...75ce59a642.jpg
What's this!? Upper link mounts more vertical..... [emoji33]

http://uploads.tapatalk-cdn.com/2016...4f8bb05b1f.jpg
While I was looking for links, I can across a VP 12.3" ti link kit.. Hmmm..
The lowers measure right! With the numbers I got, for link lengths..

But, there might be some bending needing done.. I'm sitting at 12.75"..
http://uploads.tapatalk-cdn.com/2016...6bd143797e.jpg
Good enough for mach up tho..
Shocks are a little much.. Might go with the reverse cap mod..
http://uploads.tapatalk-cdn.com/2016...0012b47972.jpg

Or better yet, I might do a full on shock swap..
Time to get some use out of this set of Rcbros shocks I have sitting around! [emoji41]

Time will tell, what comes next!

Re: Little Winner, gettin UN-Stuck..
 

So much has changed.. updates coming

Re: Little Winner, gettin UN-Stuck..
 

Your slow ...... :flipoff:

Re: Little Winner, gettin UN-Stuck..
 

5 months of nothing ....and then a teaser :x

Re: Little Winner, gettin UN-Stuck..
 

You hush!
You know these things take time... but when they are done, the grin doesn't go anywhere! :flipoff:

Re: Little Winner, gettin UN-Stuck..
 

Where do I find the carbon fiber motor guard? Build is looking good, but I seem to have forgotten about the search feature and just need to know where to find that motor guard.

Re: Little Winner, gettin UN-Stuck..
 

A vendor called Winnerone23 makes them

149 r/c worx team driver

Re: Little Winner, gettin UN-Stuck..
 

The vendor is CustomFiber... unfortunately, that star ran out and needs to be updated..
Lol... that guy is just the designer and owner! ;)

Re: Little Winner, gettin UN-Stuck..
 

Duh I could not remember the custom fiber part sorry.

149 r/c worx team driver

Re: Little Winner, gettin UN-Stuck..
 

Damn the luck. I would really like to have one of those. "thumbsup"

Re: Little Winner, gettin UN-Stuck..
 

OK, so what's changed..
Wheel base is right, new Krazed Builds wheels, Shift hubs, unstuck CF chassis plates, replaced tranny, smashed and waterproofed the electronics, replaced rear sucks with RcBros and fronts with scx..
http://uploads.tapatalk-cdn.com/2016...f9928f906b.jpg
http://uploads.tapatalk-cdn.com/2016...19b660a721.jpg
http://uploads.tapatalk-cdn.com/2016...d8c17a45a4.jpg
She's perdy!
http://uploads.tapatalk-cdn.com/2016...46843a4cb6.jpg
http://uploads.tapatalk-cdn.com/2016...0d764e7eb5.jpg
http://uploads.tapatalk-cdn.com/2016...e31b9e5c78.jpg
http://uploads.tapatalk-cdn.com/2016...dc4bb6f027.jpg
We went and ran a couple packs today, but Aiden ran my rig.. his tranny went out..
I'll try and get some pics on the rocks tomm..

Re: Little Winner, gettin UN-Stuck..
 

Another one's gone, another one's gone, another one bites the dust....
http://uploads.tapatalk-cdn.com/2016...415b60cb6c.jpg

Replaced and ready to get back to it!

Re: Little Winner, gettin UN-Stuck..
 

Good to see the boy can tear equipment up like Dad :roll:

:lmao:

Re: Little Winner, gettin UN-Stuck..
 

Sssshhhhhhh... it was dad! Lmao...

Re: Little Winner, gettin UN-Stuck..
 

End points rookie :mrgreen:

Re: Little Winner, gettin UN-Stuck..
 

Baahahaha..... what are EPR's!?

I only can find the EPA's... [emoji47]

Re: Little Winner, gettin UN-Stuck..
 

Looks like someone is snooping

Re: Little Winner, gettin UN-Stuck..
 

Boy, are you crazy!?
You can't wear antlers in the woods, around here, during hunting season.. you'll get shot!

Re: Little Winner, gettin UN-Stuck..
 

you dont need the lockedup kit, axial makes a shaft for about 6 bucks, and you you use the stock backing plate that comes with every tranny case set......."thumbsup"

you save 14 bucks"thumbsup"

the lockedup one is nice though..........;-)

Re: Little Winner, gettin UN-Stuck..
 

Ok, roksolski those are good ideas but what is the part number for the spacer that goes behind the spur gear backing plate so it dosnt slide in to far.

149 r/c worx team driver

Re: Little Winner, gettin UN-Stuck..
 

Did I miss a post? What info is this regarding?
Lol..

Re: Little Winner, gettin UN-Stuck..
 

I think roksolski did, or the fourm jumped a page. Sorry troy

149 r/c worx team driver

Re: Little Winner, gettin UN-Stuck..
 

No problem.. I will have to look back, closer.
Half asleep.. with a wrench in hand.. lol..

Re: Little Winner, gettin UN-Stuck..
 

Post #1 - Picture #3..........



Really Snaponboy, google search, or the ax10 manual....:shock:"thumbsup":lmao:

Part #ax30197
ax30162
ax30484
ax39489

i will let you do the search to find out what part no.# is what........;-)

Re: Little Winner, gettin UN-Stuck..
 

I guess thank you is in order, thank you roksolski ! I have all of those parts I was thinking I was missing something guess not.

149 r/c worx team driver

Re: Little Winner, gettin UN-Stuck..
 

who's rob?........................... not me....

Re: Little Winner, gettin UN-Stuck..
 

Ok I goofed, and I changed my goof. Sorry

149 r/c worx team driver

Re: Little Winner, gettin UN-Stuck..
 

The plastic axial slipper eliminator will hold up for a while before it ends up with a nice round 5mm hole. :lol: I killed 2 of them before getting a locked up rc metal version. The input shaft for the transmission is the same between the factory non slipper and locked up version. It would be nice if someone simply sold an alloy slipper eliminator piece instead of swapping the whole shaft etc.

Re: Little Winner, gettin UN-Stuck..
 

Oh oh, cause I days about a locked slipper.. [emoji106]

I'll just end up with a comp tranny.. hopefully a Robbob(this is Rob)/ Krazed Builds tranny!
[emoji3]
Or I'll make a bulldog trans, work..

Re: Little Winner, gettin UN-Stuck..
 

Cleaning the dust off that project once we get back from NENC :oops:

Re: Little Winner, gettin UN-Stuck..
 

They Do.......

GPM has one........."thumbsup"


and it uses the shaft you already have that has the 2 holes....

Re: Little Winner, gettin UN-Stuck..
 

Well go figure. :lol:

https://www.gpmparts.com/axial-racin...-90068905.html

Thanks for the heads up. :D

Re: Little Winner, gettin UN-Stuck..
 

this is what the GPM kit looks like put together.....
in a scaler its fine......
but in a sporty, if tou have a cross brace ,like my sporty does, this wont work because of the longer shaft...............

http://i260.photobucket.com/albums/i...ps5w6bosvi.jpg

with the short axial shaft, or the lockedup shaft the nylok nut is much closer to the spur gear........
just an FYI

Re: Little Winner, gettin UN-Stuck..
 

The un-Stuck was designed around not using a slipper ...... you wanna use the shorter shaft "thumbsup"

Re: Little Winner, gettin UN-Stuck..
 

I'm stuck with a long shaft... and it works fine.. ;)

Re: Little Winner, gettin UN-Stuck..
 

Slippers... are those the things you wear around the house... :lmao: