| |
11-17-2007, 12:56 AM
| #1 |
| Rock Crawler Join Date: May 2007 Location: lacey
Posts: 833
|  Rear Dig for sale?
I want to put rear dig on my scorpion, but I don't want to make one or spend over 100 bucks on the R2 tranny. I have seen many homemade setups that seem to work and was wondering if anyone carries a kit of some kind?
|
|  |
| Sponsored Links | |
| | |
|
11-17-2007, 01:10 AM
| #2 |
| I wanna be Dave Join Date: Jan 2006 Location: Henderson/Las Vegas, NV
Posts: 5,032
|
nope, nobody sells a kit. why not make your own? theyre easy.
|
|
| |
|
11-17-2007, 01:13 AM
| #3 |
| Rock Crawler Join Date: May 2007 Location: lacey
Posts: 833
|
oh, you know... laziness  |
|
| |
|
11-17-2007, 01:16 AM
| #4 |
| Rock Crawler Join Date: May 2007 Location: lacey
Posts: 833
|
ok then if say I were to make the attempt, anyone think of the strongest way to make such a rig? I like my equipment to be reliable.
|
|
| |
|
11-17-2007, 06:23 AM
| #5 |
| Quarry Creeper Join Date: Nov 2006 Location: land of make believe
Posts: 413
|
just use the good old "search" button. i did earlier and found 3+ different ways to make a dig setup. all of them look pretty strong.  |
|
| |
|
11-17-2007, 06:44 AM
| #6 |
| I wanna be Dave  Join Date: Jan 2004 Location: Detroit
Posts: 3,583
|
I bet if you took the time and effort to consistently make a "home made" dig set up work it'll cost you more than $100 to do it accurately. Don't be cheap or lazy... |
|
| |
|
11-17-2007, 05:19 PM
| #7 | |
| TEAM MODERATOR   Join Date: May 2004 Location: Tennessee
Posts: 10,855
| Quote:
I made the disconnect set up on my 2.2 Hustler for about 5-7 bucks. It's merely a set of maxx shafts cut,trimmed and installed correctly. Then,a cheapie servo would have worked,so about $25-30 for that and your good. I had a 359 sitting here so I used it. | |
|
| |
|
11-18-2007, 12:34 AM
| #8 |
| I wanna be Dave Join Date: Dec 2006 Location: here
Posts: 3,042
|
hey guys I made a dig for my ax10. made a servo/4 link/dig mount was pretty easy. to make the slider on drive line to look good took practice. once you get that down its not hard. Using a dig in a comp. is A+ but I would snap drive lines some times that was no good. so right now not running a dig. as for money not sure but a lot of time to get it right. after that making a dig is easy.IMO   |
|
| |
|
11-18-2007, 07:01 AM
| #9 |
| Quarry Creeper Join Date: Aug 2007 Location: tx
Posts: 254
|
If you can get a back copy of RC car action the July 2007 issue has a step by step instructions on how to make a dig setup
|
|
| |
|
12-17-2007, 11:42 AM
| #10 |
| Newbie Join Date: Oct 2004 Location: sw pa
Posts: 29
|
how do you make the rear dig setup for the ax-10 call me dumb but i can not find the posts on how to do it. thanks joe |
|
| |
|
12-17-2007, 11:48 AM
| #11 |
| Rock Crawler Join Date: Jan 2006 Location: Derbyshire UK
Posts: 623
|
This is how I did mine and it works flawlesley http://orcrc.com/forum/showthread.php?t=59 |
|
| |
|
12-17-2007, 01:07 PM
| #12 |
| Newbie Join Date: Oct 2004 Location: sw pa
Posts: 29
|
thank you for the info but now i need to fig out why the pics will not open
|
|
| |
|
12-17-2007, 01:08 PM
| #13 | |
| I wanna be Dave Join Date: Jun 2007 Location: Canada, eh.
Posts: 2,919
| Quote:
 Seriously though, I did a quick search for "rear dig" and within four threads of reading, found two threads on this site with detailed information on how to set-up dig on an AX-10 (or really any rig compatible with Maxx half shafts). Are you just being lazy? | |
|
| |
 |
| |
Linear Mode
