Let’s see the wiring masterpiece I would like to see how you wire your Capra |
Re: Let’s see the wiring masterpiece 1 Attachment(s) #masterpiece #ocdasfawk #4SornoS |
Re: Let’s see the wiring masterpiece Quote:
Darn near as good as me! ;-) Ernie |
Re: Let’s see the wiring masterpiece Quote:
|
Re: Let’s see the wiring masterpiece About as clean as I could get it. The stray red wire is my unmounted switch... https://i.ibb.co/W0JZQsV/3.jpg https://i.ibb.co/p4LCGhx/1.jpg https://i.ibb.co/vBvSXf2/2.jpg |
Re: Let’s see the wiring masterpiece I don't know about masterpiece but it works. https://i.imgur.com/13GoI4k.jpg https://i.imgur.com/xwik0UF.jpg https://i.imgur.com/TsEa3k6.jpg https://i.imgur.com/0ebhkX2.jpg |
Re: Let’s see the wiring masterpiece Why you run an external bec? |
Re: Let’s see the wiring masterpiece Running 7.4V to the steering servo and have the micro dig servo at 6V through the esc's onboard bec. |
Re: Let’s see the wiring masterpiece "thumbsup" |
Re: Let’s see the wiring masterpiece Quote:
|
Re: Let’s see the wiring masterpiece 1 Attachment(s) Not perfect, but works. |
Re: Let’s see the wiring masterpiece It's not finished, but here's what I have so far: https://uploads.tapatalk-cdn.com/201...7996522fde.jpg Headlight & servo wiring. The two 'tubes' that you see on the sides of the battery compartment contain the two antenna. I tried to glue the driver side tube in place, using CA glue, but it didn't hold, so need to come up with an alternate idea. https://uploads.tapatalk-cdn.com/201...a0f04b7adc.jpg Navigator side, where the Rx is installed. The red/black wire going straight up is the power switch, which can't be placed where it will be going...at least not yet. I also replaced the stock senator wire with a much shorter one (approx 1/3 the length), as the motor & ESC are so close to each other. https://uploads.tapatalk-cdn.com/201...f7aeb15258.jpg Driver side, where the two CPS-1 units, for remotely controlling the headlights, and lightbar, are installed on the electronics tray. As you can see, I had no choice but to "give in", and installed the ESC in front of the fuel cell. I used a pull-tie (I usually use these in building computers) to "bind" the excess lighting working together, and to hold it against the inside of the cage (driver's 'door'). https://uploads.tapatalk-cdn.com/201...cd608b2f03.jpgOverhead shot showing the ESC/motor wires, as well as the DIG servo wires, being routed around the transmission from the front side. You can also see how/where I extended the battery leads from the ESC, using ProTek EZ Solder Sleeves (AMain). Here's a closer look at them: https://uploads.tapatalk-cdn.com/201...d8f84a570c.jpg ~ More peace, love, laughter & kindness would make the world a MUCH better place |
Re: Let’s see the wiring masterpiece https://uploads.tapatalk-cdn.com/201...2424329e6c.jpg https://uploads.tapatalk-cdn.com/201...20feb81a7b.jpg https://uploads.tapatalk-cdn.com/201...49f29a94a0.jpghttps://uploads.tapatalk-cdn.com/201...08f3cb8616.jpg https://uploads.tapatalk-cdn.com/201...d5d231b268.jpg https://uploads.tapatalk-cdn.com/201...04e308b80b.jpg Sent from my iPhone using Tapatalk Pro |
Re: Let’s see the wiring masterpiece Quote:
I don't have my kit yet, but my plan was to run a direct power servo from my 3s packs at 11.1 to isolate the dig servo and just power it off the Rx at 6v. |
Re: Let’s see the wiring masterpiece Not complete yet, but this is where I started . https://uploads.tapatalk-cdn.com/201...6a8324b5aa.jpghttps://uploads.tapatalk-cdn.com/201...0174753642.jpg Sent from my moto z4 using Tapatalk |
Re: Let’s see the wiring masterpiece I figured it out. |
Re: Let’s see the wiring masterpiece 4 Attachment(s) Attachment 387084 Attachment 387085 Attachment 387086 Attachment 387087 I figured I would add some of my wiring photos. |
Re: Let’s see the wiring masterpiece Quote:
|
Re: Let’s see the wiring masterpiece Quote:
Yep, did many test fits before the location of everything was finalized, fits nicely, may goal was to get the Mamba down low up front and counter some motor weight. It took a few weeks just working on it a few times a week after work, but I am happy to start wrapping up the build now that all of the wiring is finished. |
Re: Let’s see the wiring masterpiece Quote:
I like the carbon fiber inner panels for mounting the electronics. Great idea! |
All times are GMT -6. The time now is 12:26 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com