RCCrawler Forums

cuzican · 03-31-2009, 11:42 AM

Here is the body I'll be running at the scale nats. Still gonna add a roof rack, snorkel..some other junk possibly.

Here it is with the stock body that I use for bashing because I don't wanna break the hard body before the scale nats.
Waterproof XL-5 esc and 12t titan motor.

raggydoo · 04-05-2009, 01:39 PM

grimgard · 04-10-2009, 02:36 PM

Fresh off the hobby table

tomik · 04-10-2009, 03:02 PM

Just painted...

MDcrawler710 · 04-11-2009, 04:20 PM

scx10 kit
hpi jeep body
proline scale parts

JOTE · 04-14-2009, 07:19 PM

SCX10, NOVAK GOAT BRUSHLESS 18.5, DX3R SPEKTRUM...

Bye

JOTE
CHILE

Thorno · 04-16-2009, 09:51 PM

My scx10 with tamiya fj40 body from the land down under

crawlvt · 04-22-2009, 06:38 PM

Specs:
SCX10
Clod body
Futaba S3305
Futaba 153F
Castle BEC
Castle Sidewinder
Integy 35t Lathe
Poly RC 3S Lipo
Homegrown 3/16" solid rod bumpers

I have never been one for pristine freshly painted new truck pics. I prefer showing them off after they have been "tested". Here ya go.....

josh97 · 04-22-2009, 06:50 PM

Scx-10
tazer 15t esc
jr st126 servo
out croppers on stock car wheels
proline cj8 body painted by me...

jgroneng · 04-25-2009, 02:22 AM

neung · 04-25-2009, 08:23 PM

here, it's mine .

just test run

speed88 · 04-26-2009, 06:45 AM

VinnieH · 05-02-2009, 09:58 AM

VinnieH · 05-02-2009, 10:01 AM

Big Mike · 05-06-2009, 06:38 PM

Rooster Crawler/Tekin 35t motor for now. The Rooster is a "W" series and glitches/jitters badly at low throttle. Unacceptable.
A Holmes 7t Cobalt Puller is on the way (finally!) which I will run with either a Sidewinder or an FX-R (I already have both ESCs "in stock", so experimentation is possible)
Hi-Tec 5645MG & Hand Bros. kit
3Racing winch
2 7.4 volt LiPo's (2200 mah for motor/servo and 600 mah specifically for the winch)
Controlled by a modded TQ3 (for now)

Nekkid shot. Bumpers and rock sliders are hard-mounted.
Details on bumper mounting and some closer pics can be found here if you're interested:
BM's SCX10/CGR Blazer

Pro-Line CGR Blazer w/ roof rack, lights, Western bumpers, rock sliders.
WWE wrestler JBL at the wheel (for lack of anyone better - it's hard to find a good driver!)

I am trying a set of RC4WD 90mm scale shocks for the time being. They are the same eye-to-eye length as stock, with slightly less travel. I was trying to "keep it real" suspension-wise and not go for mega-articulation, replicating a highly modified yet still street-legal truck. They work well at slow crawling speeds, but are a bit lacking at higher speeds.

Again, trying to keep it real. No sky-high, monster truck-like ride height here.

I just wasn't digging the light bar on the very top. It stuck up too far and looked like it was ready to get snagged on anything it coud reach.
I made this bracket out of black plastic and flipped the light bar upside-down. Much more streamlined looking...

Axial and Pro-Line have both hit home runs with these products. They have put a great looking scale rig within reach of a lot more people...

RCC member FodigoDave made my fire extingusher. They're not cheap, but the level of detail is absolutely unmatched. Right down to the pin, the inspection tag, even the little twisted wire that holds the tag and pin to the neck of the bottle, it's all there.
I added the 2 bands of aluminum tape, to simulate the bands of a mount.
http://www.rccrawler.com/forum/showthread.php?t=168286

neung · 05-09-2009, 07:47 AM

so far my hilux just a little change . so many truck here give so much inspiration to me.

EL BARTO 1979 · 05-10-2009, 12:38 PM

Just stock for now, still it's not to be underestimated!

EZrun 32T (1200kv) crawler (brushless) motor + esc
towerpro 995mg servo
intellect 5000 6cell , still running on the first charge after 4 hours!
Spektrum DX3.0
85gr in each front wheel, for that perfect balanced sensation

fastgixxerlv · 05-10-2009, 09:57 PM

intimadationrc · 05-11-2009, 01:11 PM

Well here's mine not to special but it's alot of fun
stock kit
with mamba max esc
revolver brushless motor
and spek radio

jakedizzle · 05-16-2009, 02:20 PM

heres my scx10 build

04-05-2009, 01:39 PM	#42
raggydoo Newbie Join Date: Jan 2009 Location: southwest mi Posts: 2	My SCX10 with stock body and Bronco body.

04-10-2009, 02:36 PM	#43
grimgard I joined the Band! Join Date: Oct 2008 Location: Bay Area Posts: 1,024	Lawn pictures Fresh off the hobby table

04-14-2009, 07:19 PM	#46
JOTE Newbie Join Date: Jun 2008 Location: CHILE Posts: 28	My SCX10... SCX10, NOVAK GOAT BRUSHLESS 18.5, DX3R SPEKTRUM... Bye JOTE CHILE

04-16-2009, 09:51 PM	#47
Thorno Newbie Join Date: Jan 2009 Location: AUS Coffs harbour Posts: 22	Thorno's fj40 scx10 My scx10 with tamiya fj40 body from the land down under

04-22-2009, 06:50 PM	#49
josh97 Quarry Creeper Join Date: Oct 2007 Location: Boringville U.S.A.! Posts: 341	my scx-10 Scx-10 tazer 15t esc jr st126 servo out croppers on stock car wheels proline cj8 body painted by me... Attached Images

03-31-2009, 11:42 AM	#41
cuzican Pebble Pounder Join Date: Jun 2008 Location: Kalispell Posts: 119	Here is the body I'll be running at the scale nats. Still gonna add a roof rack, snorkel..some other junk possibly. Here it is with the stock body that I use for bashing because I don't wanna break the hard body before the scale nats. Waterproof XL-5 esc and 12t titan motor.

04-10-2009, 03:02 PM	#44
tomik Quarry Creeper Join Date: May 2006 Location: Pirkkala, Finland Posts: 377	Just painted...

04-11-2009, 04:20 PM	#45
MDcrawler710 Newbie Join Date: Dec 2008 Location: rockville Posts: 28	scx10 kit hpi jeep body proline scale parts

04-22-2009, 06:38 PM	#48
crawlvt Newbie Join Date: Apr 2006 Location: In the sticks Posts: 8	Specs: SCX10 Clod body Futaba S3305 Futaba 153F Castle BEC Castle Sidewinder Integy 35t Lathe Poly RC 3S Lipo Homegrown 3/16" solid rod bumpers I have never been one for pristine freshly painted new truck pics. I prefer showing them off after they have been "tested". Here ya go.....

04-25-2009, 02:22 AM	#50
jgroneng Pebble Pounder Join Date: May 2007 Location: Oslo, Norway Posts: 110

04-25-2009, 08:23 PM	#51
neung Newbie Join Date: Mar 2009 Location: Rc world. Posts: 18	here, it's mine . just test run

04-26-2009, 06:45 AM	#52
speed88 Rock Stacker Join Date: Nov 2008 Location: Springfield Posts: 58	Dale Earnhardt Jr's Big Red Silverado

05-02-2009, 09:58 AM	#53
VinnieH Newbie Join Date: Apr 2009 Location: Lakeville Posts: 6

05-02-2009, 10:01 AM	#54
VinnieH Newbie Join Date: Apr 2009 Location: Lakeville Posts: 6

05-06-2009, 06:38 PM	#55
Big Mike I wanna be Dave Join Date: Oct 2006 Location: Martinsburg WV Posts: 2,781	Rooster Crawler/Tekin 35t motor for now. The Rooster is a "W" series and glitches/jitters badly at low throttle. Unacceptable. A Holmes 7t Cobalt Puller is on the way (finally!) which I will run with either a Sidewinder or an FX-R (I already have both ESCs "in stock", so experimentation is possible) Hi-Tec 5645MG & Hand Bros. kit 3Racing winch 2 7.4 volt LiPo's (2200 mah for motor/servo and 600 mah specifically for the winch) Controlled by a modded TQ3 (for now) Nekkid shot. Bumpers and rock sliders are hard-mounted. Details on bumper mounting and some closer pics can be found here if you're interested: BM's SCX10/CGR Blazer Pro-Line CGR Blazer w/ roof rack, lights, Western bumpers, rock sliders. WWE wrestler JBL at the wheel (for lack of anyone better - it's hard to find a good driver!) I am trying a set of RC4WD 90mm scale shocks for the time being. They are the same eye-to-eye length as stock, with slightly less travel. I was trying to "keep it real" suspension-wise and not go for mega-articulation, replicating a highly modified yet still street-legal truck. They work well at slow crawling speeds, but are a bit lacking at higher speeds. Again, trying to keep it real. No sky-high, monster truck-like ride height here. I just wasn't digging the light bar on the very top. It stuck up too far and looked like it was ready to get snagged on anything it coud reach. I made this bracket out of black plastic and flipped the light bar upside-down. Much more streamlined looking... Axial and Pro-Line have both hit home runs with these products. They have put a great looking scale rig within reach of a lot more people... RCC member FodigoDave made my fire extingusher. They're not cheap, but the level of detail is absolutely unmatched. Right down to the pin, the inspection tag, even the little twisted wire that holds the tag and pin to the neck of the bottle, it's all there. I added the 2 bands of aluminum tape, to simulate the bands of a mount. http://www.rccrawler.com/forum/showthread.php?t=168286 Last edited by Big Mike; 05-06-2009 at 06:41 PM.

Sponsored Links

05-10-2009, 09:57 PM	#58
fastgixxerlv Rock Stacker Join Date: Feb 2009 Location: Las Vegas Posts: 82

LinkBacks (?) LinkBack to this Thread: http://www.rccrawler.com/forum/axial-scx-10/157260-scx10-picture-archive-no-talking.html
Posted By	For	Type	Date
Link til modifiseet trial biler? - Storkøbenhavn´s kravler. - forum	This thread	Refback	02-14-2013 07:09 PM
Patski's RC Stuff! / 6x6 unimog...hmmm!	This thread	Refback	02-14-2013 05:56 PM

SCX10 Picture Archive - No talking - Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Wraith Picture Archive - No talking	Harley	Axial Wraith	1586	03-22-2023 11:32 AM
1:1 and Micro Picture Archive	MICHIGAN CRAWLER	Micro Scale Rigs	21	02-29-2012 01:02 PM
Picture archive	mental	South Carolina	21	08-18-2009 03:33 PM

05-09-2009, 07:47 AM	#56
neung Newbie Join Date: Mar 2009 Location: Rc world. Posts: 18	so far my hilux just a little change . so many truck here give so much inspiration to me.

05-10-2009, 12:38 PM	#57
EL BARTO 1979 Newbie Join Date: May 2008 Location: Belgium Posts: 48	Just stock for now, still it's not to be underestimated! EZrun 32T (1200kv) crawler (brushless) motor + esc towerpro 995mg servo intellect 5000 6cell , still running on the first charge after 4 hours! Spektrum DX3.0 85gr in each front wheel, for that perfect balanced sensation

05-11-2009, 01:11 PM	#59
intimadationrc Rock Crawler Join Date: Feb 2007 Location: weather sucks ,mn Posts: 680	Well here's mine not to special but it's alot of fun stock kit with mamba max esc revolver brushless motor and spek radio

05-16-2009, 02:20 PM	#60
jakedizzle Rock Stacker Join Date: May 2009 Location: lake elsinore Posts: 97	heres my scx10 build

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

RCCrawler Forums

Thread: SCX10 Picture Archive - No talking