11-02-2013, 12:34 PM | #1 |
Rock Crawler Join Date: Nov 2011 Location: Omaha, Nebraska
Posts: 768
| Kenneth's JK build
well i am rebuilding my truck (previous build thread here) I figured it was time to start with something different so i traded my hilux body for a new nb jk body. want to do a jk8 build but havent decided. yes i know that there are jeep builds all over the place but this is my first and ive always wanted to build one. Any way heres a list of current specs: 1.9 RC4WD Steelies 1.9 IROKS Gmade TS-01 shocks R2J Kustoms Stainless Links Traxxas 2075 Servo Axial 20T Motor AE-2 MIP rear Driveshaft Axial WB8 front driveshaft Futaba 3PL scx trans with all rrp gears Leds all around CCBec set at 7V 3Racing Winch Axial Poison Spyder rear bumper with swing away tire carrier BGR Fabrications Genright JK front bumper Upgrades to come: HH 27T Motor HH WP BRXL RC4WD Safari Snorkle Futaba 4PL Vanquish 6" Lightbar Vanquish JK light bar mounts Vanquish 1" Lightbar What do you think? Last edited by jeepscx10; 01-08-2014 at 12:31 PM. |
Sponsored Links | |
11-04-2013, 04:51 PM | #2 |
Rock Crawler Join Date: Nov 2011 Location: Omaha, Nebraska
Posts: 768
| Re: Kenneth's JK build |
11-06-2013, 06:31 PM | #3 |
Rock Crawler Join Date: Nov 2011 Location: Omaha, Nebraska
Posts: 768
| Re: Kenneth's JK build
Got the stock trans removed and detached the rear links from the skid and the frame so i could get an idea of what it will look like when i get the new links and well she looks amazing [IMG][/IMG] i have plans to paint her but not yet still want to get everything right before i throw her in the paint booth |
11-08-2013, 03:41 PM | #4 |
Rock Crawler Join Date: Nov 2011 Location: Omaha, Nebraska
Posts: 768
| Re: Kenneth's JK build
Well I figured out a way to use the stock trans without cutting into the interior (yay) and the body doesn't sit any higher than in the pic in the post above saves me a big chuck of money lol but I really wanted the ddk but limited funds doesn't allow it. Any ways got the rear bumper cut off and looks good now I am gonna finish trimming the fender flairs and wire up the leds but won't permanently install them until the body is painted. Will post pics on a bit
|
11-08-2013, 04:00 PM | #5 |
Rock Crawler Join Date: Oct 2011 Location: Canada
Posts: 593
| Re: Kenneth's JK build
Looks good! have any pics of how you got the body down so low without cutting the interior?
|
11-10-2013, 07:39 PM | #6 | |
Rock Crawler Join Date: Nov 2011 Location: Omaha, Nebraska
Posts: 768
| Re: Kenneth's JK build Quote:
[IMG][/IMG] [IMG][/IMG] i ordered my front r2j links today, still working on the fender flairs. Last edited by jeepscx10; 11-10-2013 at 07:44 PM. | |
11-15-2013, 07:41 AM | #7 |
Rock Crawler Join Date: Nov 2011 Location: Omaha, Nebraska
Posts: 768
| Re: Kenneth's JK build
Got some more done. Finished trimming the sideskirts and fender flairs last night also I saw the mold lines on the body so I sanded them down. Also got my front drive shaft yesterday from 8upboyz257 yesterday looks like its gonna work out. Also bought 2 onyx 4000mah 2s lipos from Erbing hope to have it ready before thanksgiving so I can tale it with me when I go see family over in Iowa
|
11-15-2013, 08:05 AM | #8 |
Rock Crawler Join Date: Oct 2011 Location: Canada
Posts: 593
| Re: Kenneth's JK build
Would an MIP wraith shaft work? I can't remember how much longer they are. There are several easy stock driveshaft mods if you search. One that comes to mind is use two splined with a female piece epoxied to one of them. That will get you up and running as you should have the spare parts from the kit/rtr
|
11-15-2013, 11:52 AM | #9 |
I wanna be Dave Join Date: Jan 2009 Location: New Port Richey, FL.
Posts: 2,545
| Re: Kenneth's JK build
How do you like those shocks? Was thinking of possibly getting the TS02's.
|
11-16-2013, 09:47 PM | #10 |
Rock Crawler Join Date: Nov 2011 Location: Omaha, Nebraska
Posts: 768
| Re: Kenneth's JK build
i like the shocks the only thing i dont like about them is that every once in a while the cap which is on the bottom of the shock body comes loose, other than that cant complain. front driveshaft is 2 wb8 female shafts on the outputs with a male shaft super glued to one until i get a more permanent driveshaft. Also got the holes in the fender flairs filled with bondo and sanded smooth, put a coat of primer on the body and interior and sanded and only got around to doing first coat of paint on the interior will paint the body tomorrow, im thinking white body with top, door handles, door hinges, gas cap, fender flairs, etc black and interior black with white accents in "stitching" [IMG][/IMG] [IMG][/IMG] Last edited by jeepscx10; 11-16-2013 at 09:51 PM. |
11-17-2013, 12:33 PM | #11 |
Rock Crawler Join Date: Nov 2011 Location: Omaha, Nebraska
Posts: 768
| Re: Kenneth's JK build |
11-17-2013, 06:19 PM | #12 |
Newbie Join Date: Jan 2005 Location: Houston, Texas
Posts: 36
| Re: Kenneth's JK build
Iam loving this build. Gathering parts now to finally start a build. Good inspiration!
|
11-17-2013, 06:24 PM | #13 |
I wanna be Dave Join Date: Jan 2009 Location: New Port Richey, FL.
Posts: 2,545
| Re: Kenneth's JK build
Looking good
|
11-18-2013, 06:02 PM | #14 |
Rock Crawler Join Date: Nov 2011 Location: Omaha, Nebraska
Posts: 768
| Re: Kenneth's JK build
well i got my batteries today and wanted to drive my truck to make sure all electronics were still working and plugged in the battery got steering but no throttle so i unhooked motor and took the leads and touched them to the correct leads on the battery to see if it spun nothing brand new motor ran 1 time for like 5 min in the house and know it doesnt work . know i got to get a new motor when i can get some funds together for one. anyways more good news i just masked off the body and just sprayed the fender flairs and the top with black should be dry enough in a couple hours and i will take some pics then. this is looking better than i imagined lol
|
11-18-2013, 06:23 PM | #15 |
Rock Crawler Join Date: Nov 2011 Location: Omaha, Nebraska
Posts: 768
| Re: Kenneth's JK build
just took another look at the motor and found out that the solder joint on the negative motor lead had broke. resoldered works perfect again
|
11-20-2013, 06:37 AM | #16 |
Rock Crawler Join Date: Nov 2011 Location: Omaha, Nebraska
Posts: 768
| Re: Kenneth's JK build
Got all the electronics mounted last night looks really clean other than wires from esc and motor which I made as nice as possible lol
|
11-22-2013, 03:16 PM | #17 |
Rock Crawler Join Date: Nov 2011 Location: Omaha, Nebraska
Posts: 768
| Re: Kenneth's JK build
heres a pic of the electronics mounted [IMG][/IMG] Also installed the head and taillights today [IMG][/IMG] [IMG][/IMG] also shout out to FATBOYrs10 for sending me front shock hoops for free which will be here on monday and my r2j links have shipped and will also arrive monday. gonna get her all ready to take with me when i go to iowa for thanksgiving |
11-22-2013, 07:30 PM | #18 |
RCC Addict Join Date: Aug 2011 Location: round pond (aka clarksville TN)
Posts: 1,454
| Re: Kenneth's JK build
rigs looking really good there Kenneth, and you're welcome |
11-23-2013, 05:10 PM | #19 |
Rock Crawler Join Date: Nov 2011 Location: Omaha, Nebraska
Posts: 768
| Re: Kenneth's JK build
My shock hoops and front links arrived today and I just got them installed [IMG][/IMG] |
11-23-2013, 08:31 PM | #20 |
Rock Stacker Join Date: Feb 2011 Location: British Columbia
Posts: 67
| Re: Kenneth's JK build
Really nice rig. How did you do your flat fenders? It looks like you did the same as I did on mine with the backwards trans. My front MIP was just a bit too short. I ordered wraith long drive hubs for my MIP shaft, 2 of MIP 11117. Seems to work well now, gaining about 5-6mm overall in the driveshaft length. Last edited by seanh; 11-23-2013 at 08:36 PM. |
Kenneth's JK build - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Kenneth's 1.9 Wraith Build | jeepscx10 | Axial Wraith | 69 | 03-28-2015 03:18 PM |
Kenneth's SCX10 Build | jeepscx10 | Axial SCX-10 | 59 | 11-01-2013 12:54 PM |
Jeep scaler build and comp micro crawler build | droopmodmrc | Losi Micro-Rock Crawler | 1 | 12-25-2012 12:34 PM |
~53 Willys 2010 Comp Rig Build~ RC4WD MOA Worminator Build~ | 53 willys | General Crawlers | 108 | 11-28-2011 12:42 AM |
RcBros LCC Build, Hi-Res pics & More Build!! | RcBro | Team Losi Comp Crawler | 30 | 06-03-2009 07:26 PM |
| |