RCCrawler Forums

RCCrawler Forums (http://www.rccrawler.com/forum/)
-   Axial SCX-10 (http://www.rccrawler.com/forum/axial-scx-10/)
-   -   Gspeed or custom crawl (http://www.rccrawler.com/forum/axial-scx-10/564805-gspeed-custom-crawl.html)

treadway47025 05-29-2016 09:09 AM

Gspeed or custom crawl
 
Ive narrowed to 2 chassis. Gspeed and Custom Crawl Rc. Could i get others input on these 2 or what may make one better?
Thanks

kookie31 05-29-2016 09:55 AM

Re: Gspeed or custom crawl
 
I really like my Brazin RC G10 Hi/Lohttp://uploads.tapatalk-cdn.com/2016...1272fb0f2e.jpg


Sent from my iPhone using Tapatalk

mr dave 05-29-2016 10:10 AM

Re: Gspeed or custom crawl
 
treadway, gspeed is the more conventional design and more frame components will directly swap over. The brazin chassis is a more radical design and I doubt that many original components, like the front and rear braces, will swap over. The brazin chassis will really test your builder's skills, but we don't do this hobby because its easy, right? We do it because its a challenge "thumbsup"

mr dave 05-29-2016 10:16 AM

Re: Gspeed or custom crawl
 
kookie, can't wait to see it finished, and I know what you mean about the $$$$$ :mrgreen: Looks like you're running the JK body, I see the VP rails, nice. It will be a challenge to mount the body. I see most people use the stock shock hoops and cut the tops off, then screw them to the built-in shock hoops on the lcg frames, good luck with it.

kookie31 05-29-2016 10:55 AM

Re: Gspeed or custom crawl
 
It was a bit of a challenge but got it all figured out. Had to mod the JR battery plate and the CMShttp://uploads.tapatalk-cdn.com/2016...7768f561c2.jpg
http://uploads.tapatalk-cdn.com/2016...50433ab9c5.jpg
Was able to use the rear body mounts by cutting down the stock hoops but had no room up front. Solution: Run a screw through the rockers and into the bodyhttp://uploads.tapatalk-cdn.com/2016...41ef9b8644.jpg
It works
http://uploads.tapatalk-cdn.com/2016...368781247c.jpg


Sent from my iPhone using Tapatalk

BrazinScaleRC 05-29-2016 05:17 PM

Re: Gspeed or custom crawl
 
Mr Dave. On the Brazin chassis, there is not a single factory brace that will not fit back into the Brazin rails.
To the original poster, there are a few slight differences in the two chassis you have narrowed down to, the g speed I have seen people mod to accept toyzuki forward motor mount and to me that is huge. That's why we added locations to our chassis to accept it. The custom crawl has an angled skid which j have seen be a slight advantage in some situations.

kookie31 06-01-2016 06:38 PM

Re: Gspeed or custom crawl
 
It is awesome! I'd go with a Brazin but that's just my opinion


Sent from my iPhone using Tapatalk


All times are GMT -6. The time now is 12:24 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com