| |
| |||||||
 |
| | LinkBack | Thread Tools | Display Modes |
08-26-2019, 01:45 PM
| #1 |
| Newbie Join Date: May 2019 Location: Lumberton
Posts: 38
|  SCX10ii Steering Horn Interference
I may be posting this in the wrong place, but I've looked and can't find any good info on this. Each of the 10ii builder kits I have assembled have given me trouble with the steering servo horn (metal horn) hitting the frame and shock mount/panhard mount. I have been grinding the frame a little bit for it to clearance that, but at full steer I am still hitting the shock tower/panhard mount where it hangs below the frame. What am I missing, what can be done to clearance both of these items and still get full steer to that side? Any tips or advice or sharing of knowledge of what you gusy have done is greatly appreciated. |
|  |
| Sponsored Links | |
| | |
|
08-26-2019, 03:50 PM
| #2 |
| I wanna be Dave Join Date: Jun 2016 Location: Deep in the Everglades
Posts: 5,818
| Re: SCX10ii Steering Horn Interference
20 mm horn, you might need to space the servo up 1 to 2mm Hang up and Drive |
| |
|
08-26-2019, 05:48 PM
| #3 |
| Quarry Creeper Join Date: Aug 2015 Location: Worthington
Posts: 267
| Re: SCX10ii Steering Horn Interference
What servo horn are you using?
|
|
| |
|
08-26-2019, 07:25 PM
| #4 |
| I wanna be Dave Join Date: Jun 2017 Location: Humboldt county
Posts: 4,481
| Re: SCX10ii Steering Horn Interference
I left my servo in the stock spot and just had to grind off a bit on the servo horn which IMO is better than grinding the chassis rails. But every servo is a little different dimension wise so your mileage may vary.  |
|
| |
|
08-27-2019, 02:07 AM
| #5 |
| Newbie Join Date: Apr 2019 Location: Spain
Posts: 14
| Re: SCX10ii Steering Horn Interference
I had to use spacers in the 4 holes of the servo and it would still touch the chassis. What I did was also use a file in the horn and reduce the material it had. Then with my transmitter I limit the steering angle.
|
|
| |
|
08-27-2019, 11:49 AM
| #6 |
| Newbie Join Date: May 2019 Location: Inland Empire
Posts: 38
| Re: SCX10ii Steering Horn Interference
I left my servo as is and just backed up some of the throw. Still turns decent. I will re-visit this issue when I go to swap out my servo...
|
|
| |
|
08-27-2019, 12:02 PM
| #7 |
| Newbie Join Date: May 2019 Location: Lumberton
Posts: 38
| Re: SCX10ii Steering Horn Interference
Thanks for all the replies, I will keep tinkering with it.
|
|
| |
|
08-27-2019, 03:13 PM
| #8 |
| RCC Addict   Join Date: Nov 2017 Location: 3rd rock pile on the right
Posts: 1,798
| Re: SCX10ii Steering Horn Interference
On my wifes scx10 ii, i angled the servo horn towards the passenger side away from the panhard mount. It still gets full throw without hittin the panhard mount     Sent from my SM-J327VPP using Tapatalk |
|
| |
|
08-28-2019, 01:03 PM
| #9 | |
| Newbie Join Date: May 2019 Location: Lumberton
Posts: 38
| Re: SCX10ii Steering Horn Interference Quote:
| |
|
| |
|
08-28-2019, 02:41 PM
| #10 | |
| RCC Addict Join Date: Nov 2017 Location: 3rd rock pile on the right
Posts: 1,798
| Re: SCX10ii Steering Horn Interference Quote:
Sent from my SM-J327VPP using Tapatalk | |
|
| |
|
| Tags |
| scx 10 ii, steering, steering issue |
SCX10ii Steering Horn Interference - Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Can SCX10 get similar steering throw to SCX10II? | CoolRunning | Axial SCX-10 | 27 | 03-15-2019 02:39 PM |
| Interference Between Steering and Aux 2 on spektrum... Help? | thurlo | Electronics | 0 | 12-21-2016 05:56 PM |
| steering horn help | xjeep | Axial AX-10 Scorpion | 7 | 06-14-2009 05:39 AM |
| steering servo horn | camh | Newbie General | 2 | 03-14-2009 08:24 PM |
| Thread Tools | |
| Display Modes | |
| |
Linear Mode
