|
| LinkBack | Thread Tools | Display Modes |
05-17-2020, 08:13 PM | #1 |
Pebble Pounder Join Date: Oct 2010 Location: washington
Posts: 123
| Esc placement and wire routing |
Sponsored Links | |
05-17-2020, 09:12 PM | #2 |
Newbie Join Date: Apr 2020 Location: Honeyville
Posts: 5
| Re: Esc placement and wire routing This is mine with the mytrickrc rock light wiring installed. I did move the loom off the fender too the body mount support to clear the body interior. Sent from my iPhone using Tapatalk |
05-18-2020, 06:56 AM | #3 |
Rock Crawler Join Date: Jan 2019 Location: Calgary
Posts: 566
| Re: Esc placement and wire routing
Just a word of caution with that type of loom. It can hold water and dirt, chafing wires and breaking down insulation. Also be sure to not have any stress on the loom, it can burn through the insulation eventually. |
05-18-2020, 10:59 AM | #4 |
Rock Stacker Join Date: Apr 2020 Location: Hemet
Posts: 65
| Re: Esc placement and wire routing Sent from my iPhone using Tapatalk |
05-18-2020, 03:35 PM | #5 |
Pebble Pounder Join Date: Feb 2016 Location: canandaigua
Posts: 132
| Re: Esc placement and wire routing
Wiring nightmare Sent from my SM-G930T using Tapatalk |
05-18-2020, 10:12 PM | #6 |
Rock Stacker Join Date: Jan 2017 Location: Chicago
Posts: 95
| Re: Esc placement and wire routing
This is what the spaghetti looks like so far. Still a ton to add. Waiting on a Futaba 7PX-R. After the budget recovers from that capital purchase, we will be looking to add a switchable light kit, ESS Dual sound kit, and a winch controller. Sent from my Moto Z (2) using Tapatalk |
05-21-2020, 11:00 AM | #7 |
Newbie Join Date: Mar 2020 Location: Ballston Spa
Posts: 30
| Re: Esc placement and wire routing
I put all my electronics on the same side, similar to what flatlander did. I also routed the motor and servo wires under the chassis brace and motor cover so the least amount of wire is exposed. It is pretty clean. I also put my switch right near the opening where the links can be seen, so the switch is accessible from the underside while the body is on. I'll post some pics once I figure out how to do it. |
05-21-2020, 11:37 AM | #8 | |
Pebble Pounder Join Date: Oct 2010 Location: washington
Posts: 123
| Re: Esc placement and wire routing Quote:
| |
05-21-2020, 11:39 AM | #9 |
Pebble Pounder Join Date: Oct 2010 Location: washington
Posts: 123
| Re: Esc placement and wire routing |
05-21-2020, 06:51 PM | #10 |
Newbie Join Date: Mar 2020 Location: Ballston Spa
Posts: 30
| Re: Esc placement and wire routing
My setup. I'd like to lenghten the motor wires and clean then up a bit with the braided over sleeve once I get some on hand. I also placed the on/off switch so i can access it from the bottom with the body on. |
05-21-2020, 07:37 PM | #11 | |
RCC Addict Join Date: Mar 2019 Location: Hemet
Posts: 1,214
| Re: Esc placement and wire routing Quote:
Switch. I’ll have to try that Sent from my iPhone using Tapatalk | |
05-22-2020, 10:47 AM | #12 | |
Pebble Pounder Join Date: Feb 2016 Location: canandaigua
Posts: 132
| Re: Esc placement and wire routing Quote:
Sent from my SM-G930T using Tapatalk | |
05-22-2020, 12:15 PM | #13 | |
Pebble Pounder Join Date: Oct 2010 Location: washington
Posts: 123
| Re: Esc placement and wire routing Quote:
| |
05-22-2020, 11:53 PM | #14 |
RCC Addict Join Date: Mar 2019 Location: Hemet
Posts: 1,214
| Re: Esc placement and wire routing
Finally got mine somewhat buttoned up, I’m going to remove the full size tray and move the shorty tray to the back, but leave the esc there.
|
05-23-2020, 12:58 AM | #15 | |
Pebble Pounder Join Date: Oct 2010 Location: washington
Posts: 123
| Re: Esc placement and wire routing Quote:
| |
05-23-2020, 09:22 PM | #16 |
Pebble Pounder Join Date: Feb 2016 Location: canandaigua
Posts: 132
| Re: Esc placement and wire routing |
05-25-2020, 01:50 PM | #17 |
Rock Crawler Join Date: May 2014 Location: Cluj-Napoca,Romania
Posts: 650
| Re: Esc placement and wire routing
Any picture with a mamba X and bot micros and the side battery setup?
|
05-26-2020, 02:33 PM | #18 |
Newbie Join Date: Apr 2020 Location: New Hampton
Posts: 18
| Re: Esc placement and wire routing Hows this? HHpuller pro v2 3300 Mamba x 777 |
05-26-2020, 02:51 PM | #19 |
Newbie Join Date: Apr 2020 Location: New Hampton
Posts: 18
| Re: Esc placement and wire routing |
06-04-2020, 04:00 PM | #20 |
Newbie Join Date: Nov 2017 Location: MINERAL WELLS
Posts: 21
| Re: Esc placement and wire routing Sent from my iPhone using Tapatalk |
Esc placement and wire routing - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Esc placement | CrawlBot | Electronics | 4 | 02-17-2014 02:37 AM |
help with placement of esc on scx10 | toyman75 | Minnesota | 3 | 11-05-2012 11:08 AM |
RX and ESC placement thoughts. | RickM | Losi Mini-Rock Crawler | 4 | 04-18-2010 10:02 PM |
Wire Routing.. | zaner123 | Electronics | 1 | 11-09-2008 10:30 PM |
Lipo wire smaller than ESC wire..problem? | solomon7 | Electronics | 3 | 03-27-2008 08:45 PM |
| |