06-27-2020, 01:34 AM | #1 |
Newbie Join Date: Oct 2015 Location: Surprise
Posts: 24
| Dig/4WD throw dimension
Instructions (bottom of C4) indicate an exposed shaft dimension of 6.99mm with DIG engaged and 0.89mm in 4WD mode. The total travel on my assembly is about 4mm. This means while I have the 6.99mm with DIG engaged, I have about 3mm of exposed shaft in 4WD instead of 0.89mm I'm thinking this is another typo but I'm not sure which number is wrong. Has anyone else run into this issue? |
Sponsored Links | |
06-27-2020, 06:31 AM | #2 |
Pebble Pounder Join Date: Jan 2017 Location: Tucson
Posts: 120
| Re: Dig/4WD throw dimension
I am right about at the 6.99 engaged and .89 disengaged. Just measured it to check. Are you measuring it without the servo connected or connected? My measurements were with it connected. Sent from my moto z4 using Tapatalk |
06-27-2020, 07:55 AM | #3 |
Pebble Pounder Join Date: Jan 2017 Location: Tucson
Posts: 120
| Re: Dig/4WD throw dimension
Another thought, have you spun the transmission while it is disengaged? The trans needs to spin a little to fully disengage the dig and the shaft to go fully in to place. Sent from my moto z4 using Tapatalk |
06-27-2020, 08:21 AM | #4 |
Newbie Join Date: Oct 2015 Location: Surprise
Posts: 24
| Re: Dig/4WD throw dimension
I am measuring without the servo connected. Also I made sure to spin the transmission to fully engage and disengage the DIG mechanism. I'll try and post a picture. Now I'm worried I have a gear in backwards or something, although everything went together very smoothly. I should also add that it functions correctly. It engages and disengages the rear axle connection smoothly. Last edited by debrent; 06-27-2020 at 08:39 AM. |
06-27-2020, 09:49 AM | #5 |
Pebble Pounder Join Date: Jan 2017 Location: Tucson
Posts: 120
| Re: Dig/4WD throw dimension
Maybe someone else here has some ideas, 2mm off seems a little odd. Do you have the rig up and running yet? If it is functioning properly under load I'm not sure if I'd worry a whole lot. Sent from my moto z4 using Tapatalk |
06-27-2020, 10:39 AM | #6 |
Newbie Join Date: Oct 2015 Location: Surprise
Posts: 24
| Re: Dig/4WD throw dimension
Okay, so I guess was up too late working on this. When I went to take some pictures to post here the measurements look correct. I think my calipers may not have been zeroed last night and I was too tired to notice. Sorry for the false alarm... I do actually have another question regarding installation of my Axe 540 brushless motor system that I will post in a new thread. |
Dig/4WD throw dimension - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
dna dig no 4wd | Bukwylde | Axial AX-10 Scorpion | 14 | 04-10-2011 08:37 AM |
Hr dig..2wd-4wd | xxkalladorxx | Axial SCX-10 | 7 | 10-17-2009 10:10 AM |
Home made Dig Throw Question | Harvo | Newbie General | 2 | 06-12-2008 09:14 AM |
Dig ?, 4wd-fwd-brake Or 4wd-fwd Only ? | twisted | General Crawlers | 2 | 01-12-2008 02:26 PM |
Benifits of Dig vs 4wd | Dustyk | Newbie General | 11 | 04-16-2007 09:01 AM |
Thread Tools | |
Display Modes | |
| |