|
| LinkBack | Thread Tools | Display Modes |
10-05-2011, 07:21 PM | #81 |
20K Club Join Date: Jul 2004 Location: Sending illegals home one Hayabusa at a time.
Posts: 22,981
| |
Sponsored Links | |
10-05-2011, 07:23 PM | #82 |
I wanna be Dave Join Date: Dec 2005 Location: Happiness is a warm AK.
Posts: 12,563
|
Page 5 and not a build in sight. Only an ASSHOLE like you could get away w/ this. |
10-05-2011, 08:59 PM | #83 |
20K Club Join Date: Jul 2004 Location: Sending illegals home one Hayabusa at a time.
Posts: 22,981
|
Stock out, underdrive in.
|
10-05-2011, 09:03 PM | #84 |
RCC Addict Join Date: Jun 2008 Location: Amish Buggy PA
Posts: 1,100
| I use that exact cut on my LCC and it works extremely well for my setup. But then again I really dont think you can truely go wrong with any pin tire cut pattern. I have tried three or four styles and they all seem to work about the same.
|
10-05-2011, 09:21 PM | #85 |
20K Club Join Date: Jul 2004 Location: Sending illegals home one Hayabusa at a time.
Posts: 22,981
|
Rear is back assembled for now. Waiting on all the VP stuff. Width came out much wider than I wanted but oh well. Sitting at 11.25" right now. It's wide but I'll give it a shot. |
10-05-2011, 09:25 PM | #86 |
20K Club Join Date: Jul 2004 Location: Sending illegals home one Hayabusa at a time.
Posts: 22,981
|
Used some of the Rock Lube when I installed the gears. I do love that squeeze bottle.
|
10-05-2011, 10:37 PM | #87 |
I wanna be Dave Join Date: May 2011 Location: Lost in Oregon
Posts: 4,450
|
Pictures...I think I saw pictures !!!
|
10-05-2011, 11:05 PM | #88 |
20K Club Join Date: Jul 2004 Location: Sending illegals home one Hayabusa at a time.
Posts: 22,981
|
Front overdrive installed and lubed. Waiting on shafts.
|
10-05-2011, 11:06 PM | #89 |
20K Club Join Date: Jul 2004 Location: Sending illegals home one Hayabusa at a time.
Posts: 22,981
|
Electronics arrived today. That 157 is over 500 oz/in of torque and SUPER fast. It's a beast.
|
10-05-2011, 11:08 PM | #90 |
20K Club Join Date: Jul 2004 Location: Sending illegals home one Hayabusa at a time.
Posts: 22,981
|
Going to run a standard trans that loaded up inside. Junfac shafts are on as well.
|
10-05-2011, 11:10 PM | #91 |
20K Club Join Date: Jul 2004 Location: Sending illegals home one Hayabusa at a time.
Posts: 22,981
|
Beefy Robotronics arm from TCS.
|
10-05-2011, 11:41 PM | #92 |
RCC Addict Join Date: Oct 2008 Location: Alpine,CA
Posts: 1,258
| I can't get my greasy paw's on a set. You....* EDIT: Did this set have the hole for the screwpin or was it old style ? Last edited by DiEzel; 10-05-2011 at 11:44 PM. |
10-07-2011, 10:10 AM | #93 |
20K Club Join Date: Jul 2004 Location: Sending illegals home one Hayabusa at a time.
Posts: 22,981
|
Looks like some posts were lost in the crash yesterday. Anyway, looks like this rig will have to be completed next week. Shipping didn't quite make it in time. |
10-07-2011, 01:21 PM | #94 |
RCC Addict Join Date: Feb 2008 Location: Winnipeg
Posts: 1,296
|
BOOOOO lol... Oh well i"m still here for the long run... Love seeing your builds .
|
10-07-2011, 01:47 PM | #95 |
20K Club Join Date: Jul 2004 Location: Sending illegals home one Hayabusa at a time.
Posts: 22,981
| |
10-07-2011, 02:30 PM | #96 |
Rock Crawler Join Date: Feb 2008 Location: CHESAPEAKE, Va
Posts: 556
| |
10-08-2011, 07:49 AM | #97 |
Quarry Creeper Join Date: Oct 2008 Location: Folsom
Posts: 215
|
Looking good as always Harley.... Keep us informed on progress.... |
10-09-2011, 07:58 AM | #98 |
RCC Addict Join Date: Feb 2008 Location: Winnipeg
Posts: 1,296
|
Brutal! Mine always comes at the end of the day too.. kinda nice cause I'm normally home by then and it's like a kid on Christmas to see what part showed up that day lol
|
10-11-2011, 08:45 PM | #99 |
Rock Stacker Join Date: Jun 2011 Location: In the Reptile Shack
Posts: 82
|
Any up dates or are you still waiting on parts?
|
10-11-2011, 08:57 PM | #100 |
20K Club Join Date: Jul 2004 Location: Sending illegals home one Hayabusa at a time.
Posts: 22,981
| |
Thread Tools | |
Display Modes | |
| |