pros and cons of robinson one peice bottom gear I stripped my stock bottom gear. Which would be best to replace it. Either the Robinson one peice or the Robinson bolt together gear. Price diftence isn't a hole lot. Just curious what you guys think on it. I've already installed the Robinson idler. Thanks |
Re: pros and cons of robinson one peice bottom gear The one piece won't let you add the dig unit if you ever decide to. |
Re: pros and cons of robinson one peice bottom gear Depends, do you ever plan on doing a dig unit??? If so go multi piece, if not single piece. One way to look at it is, if it is one piece there is less to go wrong... |
Re: pros and cons of robinson one peice bottom gear The one-piece will also NOT let you use the AX10 transmission housing, for instance the nice VP one. I have the one piece and I somewhat regret the decision. I'll probably end up going with the Crawler Innovations setup and have the 1-piece left-over (or for sale) |
Re: pros and cons of robinson one peice bottom gear Quote:
|
Re: pros and cons of robinson one peice bottom gear Quote:
|
Re: pros and cons of robinson one peice bottom gear Thanks guys. I'll order the multi piece |
Re: pros and cons of robinson one peice bottom gear From what I know, no, you can't use the one-piece with the VP case. Here is what I got from Crawler Innovations: "The BDW motor plate fits AX/SCX Transmission cases only. The wraith trans is completely different. If you have the one piece RR wraith locker, it is wraith only. To use the motor plate, you need; AX/SCX Trans case - Axial part# AX80009 Rob. Rac. Gear - Part # 1540 CI trans outputs" So that's what I know. Hope this helps! And I'm not selling my one-piece just yet, I don't have the other parts yet ;-) |
Re: pros and cons of robinson one peice bottom gear Oh I think that is only if you use BWD motor plate?? I have the stock axial plate. I don't see how different the stuff from AX/SCX and Wraith are inside the trans. After all VP sells us the AX/SCX aluminum trans cases for the Wraith. Hmmmmmmm. Here is BWD motor plate and yes only for AX/SCX but I was told it can work on stock Wraith parts. http://stores.intuitwebsites.com/Bil...ate/Detail.bok |
Re: pros and cons of robinson one peice bottom gear It has nothing to do with the motor plate and everything to do with the rear half of the transmission housing. Wraith has a dig extension built into the housing requiring a longer rear output, AX/SCX case does not, hence very different rear output design. One piece Wraith RR will not work with AX/SCX rear case half |
Re: pros and cons of robinson one peice bottom gear Right, precisely what BikingViking said. My quote from Crawler Innovations included the motor plate, since that is the part that I bought that didn't fit the Wraith transmission housing. But I got all the other info with it, so I wanted to share it for completeness. Apologies for the confusion! |
Re: pros and cons of robinson one peice bottom gear Quote:
|
Re: pros and cons of robinson one peice bottom gear Okay another question about Robinson Racing gears and the VP trans case? Can I order RRP1552 and use the Wraith stock outputs? Or do I need RRP1540 and the Wraith outputs? I am really confused with the VP case!! http://www.rpphobby.com/product_p/rrp1552.htm http://www.rpphobby.com/product_p/rrp1540.htm |
Re: pros and cons of robinson one peice bottom gear I first went with the the Robinson Racing Hardened Steel Bottom Diff Gear Wraith but after a few packs with my HV 4.5 motor, it bent the out put shaft, Pic Below, enough to cause my drive shaft to whobble pretty bad. So I ended up buying the RR one piece. Comparing the two, the One piece is Beefy. http://www.axialracing.com/assets/pr...jpg?1318016830 http://www.rpphobby.com/v/vspfiles/p...RRP1555-2T.jpg |
Re: pros and cons of robinson one peice bottom gear Well if you are using an AX/SCX case (Vanquish) you could use a one piece AX output, basically all that is interchangeable is top gear and idler gear, the rest is different parts: bottom gear/outputs, rear case half, etc Robinson Racing Outdrive Diff Lock Gear AX10/SCX10 |
Re: pros and cons of robinson one peice bottom gear Oh I guess I might have to sell my VP case I don't even have in my hands yet!! or maybe just use the front half of the case put the one piece bottom gear and not worry!! I am kind of mad at myself for not having a clue. Now I know. I guess I could also sell the VP case and get the HR Wraith one and use the parts then. I know VP is probably better quality but they don't make a full Wraith trans case!! Ahhhhhhhhhhhh. Live and learn!! Only Money right??????????? |
Re: pros and cons of robinson one peice bottom gear Get the one piece AX10 gear for your VP case, OR go with the RR gear (just the gear) and the Crawler Innovations outputs. If cash is a problem, run the RR one-piece in your Wraith plastic case for now, and then swap that out for the VP case with the needed outputs later. That's what I'm going to do I think. |
Quote:
https://images-na.ssl-images-amazon....160_SS140_.jpg |
Re: pros and cons of robinson one peice bottom gear Or sell the VP case (other than being pretty its tolerances weren't worth the money on the 3 I tried to assemble with good gears at Nationals with SuperShafty Rick). The HotRacing case (they make a wraith specific one) is real nice. Everything fits right too. |
Re: pros and cons of robinson one peice bottom gear Quote:
|
All times are GMT -6. The time now is 10:52 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com