|
| LinkBack | Thread Tools | Display Modes |
05-29-2015, 04:46 PM | #1 |
Rock Stacker Join Date: May 2015 Location: Desert
Posts: 65
| Need help spur gears different
I have a wraith spawn and the spur gear has friction pads on doesnt have the 3 screws holding it in. But the manuals im reading shows it has the 3 screws
|
Sponsored Links | |
05-29-2015, 05:02 PM | #2 |
RCC Addict Join Date: Jul 2012 Location: Oreganastan
Posts: 1,151
| Re: Need help spur gears different |
05-29-2015, 05:25 PM | #3 |
Pebble Pounder Join Date: Oct 2014 Location: bellville
Posts: 144
| Re: Need help spur gears different |
05-29-2015, 05:48 PM | #4 |
I wanna be Dave Join Date: Nov 2014 Location: West Texas
Posts: 2,654
|
Is the spur gear held on by the spring and washer? Meaning if you remove the nut the spring washer etc dose the spur come off if so them Axial may just need to update the manual. My dingo kit manual said a spacer went in between the main Trans gear and the diff cups but if actually did not.
|
05-29-2015, 06:00 PM | #5 |
Pebble Pounder Join Date: Oct 2014 Location: bellville
Posts: 144
| Re: Need help spur gears different
The Wraith Spawn uses new dual slipper design and 32 pitch gears. This is the old single slipper that uses 48 pitch gears. |
05-29-2015, 06:10 PM | #6 |
Rock Stacker Join Date: May 2015 Location: Desert
Posts: 65
| Re: Need help spur gears different
Yes i read the manual. And was going to get gear ratio for stock motor. I bought the stuff for single slipper. So the spawn has this is it only on newer wraiths? And what gear ration do i need ? Do i still get 86/14 with 36 pitch
|
05-29-2015, 06:21 PM | #7 |
Pebble Pounder Join Date: Oct 2014 Location: bellville
Posts: 144
| Re: Need help spur gears different 86/14 would be really slow. Your Wraith has 56/12 32 pitch in it now. What are you trying to do?
Last edited by Reddog95; 05-29-2015 at 06:26 PM. |
05-29-2015, 06:33 PM | #8 |
Pebble Pounder Join Date: Oct 2014 Location: bellville
Posts: 144
| Re: Need help spur gears different
If you want to slow it down a little. I would get RRP#8611 AND RRP#1200.
|
05-29-2015, 06:50 PM | #9 |
Rock Stacker Join Date: May 2015 Location: Desert
Posts: 65
| Re: Need help spur gears different
Well i read the sticky about gears and was going to do that since i had stock motors and it said the gears are too high for stock motor is that page not for this in some aspects? Wasnt tryimg to change anything just do what it recomemded
|
05-29-2015, 06:53 PM | #10 |
I joined the Band! Join Date: Dec 2014 Location: Earth
Posts: 1,188
| Re: Need help spur gears different
Just buy the 1/8" (3.17mm) shaft 11 tooth pinion. Axial TowerHobbies.com | Axial Pinion Gear 32P 11T Steel 3mm Motor Shaft RRP alloy steel TowerHobbies.com | Robinson Racing Pinion Gear 32P 11T RRP Absolute heat treated steel TowerHobbies.com | Robinson Racing Pinion Gear Absolute 32P 11T |
05-29-2015, 06:55 PM | #11 |
Pebble Pounder Join Date: Oct 2014 Location: bellville
Posts: 144
| Re: Need help spur gears different
Yous is geared better than the Wraith with 48 pitch gears. It comes with 80/20. Witch equals 4 to 1 ratio, your is 4.6 to 1. Most say 5 to 1 is perfect. 56/11 is 5.09 to 1.
|
05-29-2015, 06:57 PM | #12 | |
Pebble Pounder Join Date: Oct 2014 Location: bellville
Posts: 144
| Re: Need help spur gears different Quote:
| |
05-29-2015, 07:41 PM | #13 |
I joined the Band! Join Date: Dec 2014 Location: Earth
Posts: 1,188
| Re: Need help spur gears different |
Need help spur gears different - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Spur gears? | Locked Up | Axial Yeti | 19 | 04-15-2015 02:22 AM |
spur gears | popeye123 | Axial Wraith | 6 | 01-10-2013 10:25 PM |
Questions about spur gears and pinion gears... | Chadworkz | General Crawlers | 6 | 12-03-2008 02:04 PM |
Spur gears | Troublemaker | HPI Wheely King | 11 | 07-06-2007 06:05 AM |
Thread Tools | |
Display Modes | |
| |