|
| LinkBack | Thread Tools | Display Modes |
10-26-2017, 02:36 PM | #1 |
Quarry Creeper Join Date: Feb 2007 Location: Lleida
Posts: 281
| Wraith transmission case
Hello, I want to replace stock plastic transmission case for aluminium one’s. Is there any model that fit w/o swap any stock part, gears, axles... Best regards |
Sponsored Links | |
10-26-2017, 04:32 PM | #2 |
I wanna be Dave Join Date: Jun 2016 Location: Deep in the Everglades
Posts: 5,818
| Re: Wraith transmission case
Look at the VP vanquish products. I built mine based on that and the super shafty bombproof Hang up and Drive |
10-26-2017, 06:55 PM | #3 |
RCC Addict Join Date: May 2013 Location: Forrestfield, Western Australia
Posts: 1,082
| Re: Wraith transmission case
If you haven't swapped out the stock gears for metal yet that'd be a better spend than the trans case. Wraith trans theres a few options but VP isn't one, you'll need to change the rear output to suit that (AX10/SCX10 trans basically) The HR one in the pic above is available from Tower & RPP https://www.towerhobbies.com/cgi-bin...?&I=LXFHTS&P=7 Hot Racing Black Aluminum Wraith Transmission Case Then theres also GPM for AXIAL Wraith #WR038-GS (FREE SHIPPING), ,(WR038-GS) by GPM Aluminum Alloy Transmission Case Grey Silver https://www.asiatees.com/display?Axi...id=61836&pid=1 and Boom have one also https://www.asiatees.com/display?Axi...d=116523&pid=1 |
10-26-2017, 11:47 PM | #4 | |
Quarry Creeper Join Date: Dec 2016 Location: Cawston, British Columbia, Canada
Posts: 478
| Re: Wraith transmission case Quote:
| |
10-27-2017, 02:23 AM | #5 | |
RCC Addict Join Date: May 2013 Location: Forrestfield, Western Australia
Posts: 1,082
| Re: Wraith transmission case Quote:
The SCX10 GPM case I have was another matter. Same HR gears but the bosses at the mid shaft bearings were too large & kept the case apart. Took just touch with a counter sink bit (yes an end mill would be the correct tool but I didn't have one to hand) to remove enough material to fix but does show their consistency isn't quite 100% | |
10-27-2017, 11:09 PM | #6 |
Newbie Join Date: Jul 2017 Location: Albuquerque
Posts: 1
| Re: Wraith transmission case
I got rid of the stock plastic when I stripped the gears. Right now I run the Team GPM #WR038. Not one issue with it. All the bearings and upgraded metal gears from axial fit perfectly. No need to shim or anything.
|
10-28-2017, 12:07 PM | #7 |
Rock Stacker Join Date: Mar 2015 Location: NC
Posts: 97
| Re: Wraith transmission case
the VP SCX10 transmission cases are also very good. I use that with Super Shafty Beefy top shaft, motor plate, 6mm output shafts, Robinson Racing slash slipper, and metal internal gears. No issues and spins great.
|
11-13-2017, 12:21 PM | #8 |
Quarry Creeper Join Date: Feb 2007 Location: Lleida
Posts: 281
| Re: Wraith transmission case
Finally I bought GPM aluminium case. Thank you guys! |
Wraith transmission case - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Axial Wraith Spawn RTR Transmission Case Question | raider89 | Axial Wraith | 2 | 06-12-2015 12:38 PM |
Transmission case | Satheddal | Axial SCX-10 | 2 | 07-19-2014 07:32 PM |
| |