RCCrawler Forums

iammakbeth · 08-17-2020, 07:45 PM

My wraith 1.9 is 2 weeks old with no hard crashes on the bumper! Just general low speed crawling. I’ve seen different front braces from the Harley turbos to the Blake’s brace on the vendor forum. Has anyone come up with a definite solution?

Shinchu · 08-17-2020, 11:04 PM

There were a bunch of aftermarket solutions for this when it came out.
Just keep looking at older build threads in this section or search for wraith brace.

Crawlsalot · 08-22-2020, 04:12 PM

I have the ssd combo and beat the tar out my wraith with zero issues up front.. recently went brushless and still going strong

iammakbeth · 08-23-2020, 11:02 AM

Anyone have this installed? Thoughts?

https://www.amainhobbies.com/bp-cust...saArrfEALw_wcB

After replacing my rails, I have noticed quite a bit of flex at the chassis side panhard mount when my servo is throwing to the right. This seems to be a solution to both stiffen the front end as well as give me a solid panhard mount on the chassis.

08-17-2020, 07:45 PM	#1
iammakbeth Newbie Join Date: Jul 2020 Location: New York Posts: 3	Another set of lower rails bites the dust, what is the best solution? My wraith 1.9 is 2 weeks old with no hard crashes on the bumper! Just general low speed crawling. I’ve seen different front braces from the Harley turbos to the Blake’s brace on the vendor forum. Has anyone come up with a definite solution? Last edited by iammakbeth; 08-17-2020 at 07:56 PM.

08-17-2020, 11:04 PM	#2
Shinchu I wanna be Dave Join Date: Dec 2016 Location: san diego Posts: 2,723	Re: Another set of lower rails bites the dust, what is the best solution? There were a bunch of aftermarket solutions for this when it came out. Just keep looking at older build threads in this section or search for wraith brace.

08-22-2020, 04:12 PM	#3
Crawlsalot Rock Crawler Join Date: Sep 2005 Location: wyckoff, NJ Posts: 639	Re: Another set of lower rails bites the dust, what is the best solution? I have the ssd combo and beat the tar out my wraith with zero issues up front.. recently went brushless and still going strong

08-23-2020, 11:02 AM	#4
iammakbeth Newbie Join Date: Jul 2020 Location: New York Posts: 3	Re: Another set of lower rails bites the dust, what is the best solution? Anyone have this installed? Thoughts? https://www.amainhobbies.com/bp-cust...saArrfEALw_wcB After replacing my rails, I have noticed quite a bit of flex at the chassis side panhard mount when my servo is throwing to the right. This seems to be a solution to both stiffen the front end as well as give me a solid panhard mount on the chassis.

Another set of lower rails bites the dust, what is the best solution? - Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Another one bites the dust...servo	NitroDarwin	Axial RR10 Bomber	46	02-23-2019 01:32 PM
Another one bites the dust! 8th motor and counting..HELP!!!!	hiluxscaler	Electronics	18	02-19-2012 10:20 AM
Another one bites the dust!	camel_rc	Electronics	2	02-28-2008 12:21 PM
Another 945mg bites the dust!	BENDER	Electronics	22	02-27-2005 02:49 AM

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Sponsored Links

RCCrawler Forums

Thread: Another set of lower rails bites the dust, what is the best solution?