Go Back   RCCrawler Forums > RCCrawler Brand Specific Tech > Heritage Crawlers > Axial XR10
Loading

Notices

Thread: Best XR10 Wiring Jobs...

Reply
 
LinkBack Thread Tools Display Modes
Old 01-28-2011, 07:18 AM   #1
Pebble Pounder
 
Join Date: Dec 2008
Location: The Dirty Dirty, A-Town, ATL, The A, Hot-Lana, ATLANTA GEORGIA
Posts: 115
Default Best XR10 Wiring Jobs...

How bout a spot to show off your clean XR10 Wiring. If you can, list your components(ESC(s), BEC, Battery, Reciever), wire gauge, connectors, ect..
mrdrinksalil is offline   Reply With Quote
Sponsored Links
Old 01-28-2011, 07:27 AM   #2
I wanna be Dave
 
Join Date: Oct 2007
Location: Scumrise, Flooriduh
Posts: 5,181
Default

Not the best, but not bad for an idiot like me:

Two fxr's, 1000 uF cap bridged between both, castle bec:




installed, nice and low

DickyT is offline   Reply With Quote
Old 01-28-2011, 09:57 AM   #3
Pebble Pounder
 
Join Date: Dec 2008
Location: Finland
Posts: 133
Default

2xFXR, CCBec, spectrum 6ch, over the battery tray
laalaa is offline   Reply With Quote
Old 01-28-2011, 10:03 AM   #4
Quarry Creeper
 
Join Date: Mar 2008
Location: N. Ridgeville , Ohio
Posts: 461
Default

Specs:
Sidewinder esc
Punk dig
jr 9100t servo with losi aluminum servo horn
Castle creations BEC
Spektrum DX3 with sr3000 RX
Thunder power 850mah 3 cell li-po 45c
or
Common sense 850mah 3 cell li-po 30c
Integy 45 turn motors 15 tooth pinion front, 13 tooth pinion rear
electronics/battery tray made from old dettatchable radio face case
vn1500 is offline   Reply With Quote
Old 01-28-2011, 10:35 AM   #5
Rock Crawler
 
Join Date: Apr 2009
Location: Arizona
Posts: 745
Default

wireing doen by SMOKEY...
fxr
punk dig
cc bec
rx
briansbodies is offline   Reply With Quote
Old 01-28-2011, 10:37 AM   #6
Rock Crawler
 
Join Date: Jan 2007
Location: in my bubble
Posts: 532
Default

Quote:
Originally Posted by briansbodies View Post
wireing doen by SMOKEY...
fxr
punk dig
cc bec
rx
this looks CLEAN !! Its amazing what a little wire wrap will do. I need to pick some up.
aaugman is offline   Reply With Quote
Old 01-28-2011, 11:48 AM   #7
Rock Crawler
 
Join Date: Jun 2010
Location: Yelm,WA
Posts: 695
Default

Quote:
Originally Posted by briansbodies View Post
wireing doen by SMOKEY...
fxr
punk dig
cc bec
rx
Do you know where one could pick up that wrap?
BFGcrawler418 is offline   Reply With Quote
Old 01-28-2011, 11:54 AM   #8
Quarry Creeper
 
Join Date: Jun 2009
Location: Abbotsford BC Canada
Posts: 236
Default

I like the look of of a few wires myself..I can unplug both motors and all of the punk dig wiring..I soldered female bullet plugs right to bottom of the Punk Dig

I have shortened up the ESC to Punk wires since pic was taken

Must Admit smoky's wiring is about the cleanest that i've see yet

Second pic is more recent and messier..Added a few goodies
Attached Images
  

Last edited by xv-townboy; 01-28-2011 at 12:15 PM.
xv-townboy is offline   Reply With Quote
Old 01-28-2011, 12:44 PM   #9
RCC Addict
 
Join Date: Jun 2008
Location: Nunya Idaho...
Posts: 1,559
Default

Can we have a "messiest" wiring thread? lol.
slowngreen is offline   Reply With Quote
Old 01-28-2011, 01:37 PM   #10
Quarry Creeper
 
Join Date: Jun 2009
Location: Abbotsford BC Canada
Posts: 236
Default

Hey you dont like my new word..Fashioned after the hockey player Mark Messier
xv-townboy is offline   Reply With Quote
Old 01-28-2011, 02:02 PM   #11
Quarry Creeper
 
Join Date: Nov 2010
Location: Canada
Posts: 383
Default

Mine looks like the clean one. I picked up some of the wire wrap CHEAP from Hobby King. Its like 20 cents a meter or something. They have it in lots of different colors. I chose black as the whole rig is blacked out. You can get it in 3 different sizes too. I got some small stuff for my micro crawler and one that fits servo wires, and then the big stuff like in that picture above for the motor wires.

It does make it look as clean as possible. I hated the rats nest when I first built it.

Tip, zip tie it to the wires then use a hot knife to cut it. This will melt the webbing together to prevent it from fraying out.

I would imagine things would look even cleaner if someone used the factory electronics tray and some of this wire wrap.
BurnLatex is offline   Reply With Quote
Old 01-28-2011, 02:06 PM   #12
Rock Crawler
 
Join Date: Sep 2010
Location: Little Rock, AR
Posts: 596
Default

dual tekin rs, futaba 614 rx is the only thing in the chassis on my truck, this is what i looks like when i pull the cab off. (switch is zip tied to cab)


Battery is on the front axle, CC bec is under the servo.
Rootar is offline   Reply With Quote
Old 01-28-2011, 06:21 PM   #13
RCC Addict
 
Join Date: Jul 2009
Location: Santa Rosa, CA
Posts: 1,349
Default

Wiring done by Charlie, he's a member here and the guy from my LHS.

Two Tekin fxr's
CC BEC
7 channel Futaba rx




Last edited by shelby; 01-28-2011 at 08:25 PM.
shelby is offline   Reply With Quote
Old 01-29-2011, 03:20 AM   #14
Pebble Pounder
 
Join Date: Jul 2008
Location: Grand Island (middle of Nebraska)
Posts: 137
Default

Quote:
Originally Posted by briansbodies View Post
wireing doen by SMOKEY...
fxr
punk dig
cc bec
rx
Now after 30yrs of rc..I dont think I have ever seen a nicer wiring job, awesome work!
Darth Smoke is offline   Reply With Quote
Old 01-29-2011, 09:22 AM   #15
Quarry Creeper
 
Join Date: Mar 2004
Location: VA
Posts: 475
Default

Quote:
Originally Posted by BFGcrawler418 View Post
Do you know where one could pick up that wrap?
Heres one sourse
http://www.parts-express.com/wizards...fg&srchMfg=299
4XADICT is offline   Reply With Quote
Old 01-29-2011, 09:41 AM   #16
Quarry Creeper
 
Join Date: Sep 2009
Location: Vancouver,Canada
Posts: 212
Default

[QUOTE]
Originally Posted by BFGcrawler418
Do you know where one could pick up that wrap?


And here is another source

http://www.hobbyking.com/hobbyking/s...t=&LiPoConfig=
cliffhanger007 is offline   Reply With Quote
Old 01-29-2011, 01:54 PM   #17
Rock Crawler
 
Join Date: Jun 2010
Location: Yelm,WA
Posts: 695
Default

Thanks Guys

Last edited by BFGcrawler418; 01-29-2011 at 02:48 PM.
BFGcrawler418 is offline   Reply With Quote
Old 01-29-2011, 04:55 PM   #18
Quarry Creeper
 
Join Date: Jan 2011
Location: Michigan
Posts: 237
Default

It's pretty hard to argue about this, the "Smokey" wiring job is hands down the way to go But it does make me wonder why I did not see this or think of it myself years ago!


KUDOS




Quote:
Originally Posted by briansbodies View Post
wireing doen by SMOKEY...
fxr
punk dig
cc bec
rx
Rockwolf is offline   Reply With Quote
Old 01-29-2011, 08:02 PM   #19
RCC Addict
 
Join Date: Mar 2010
Location: Alburtis
Posts: 1,227
Default

I am not sure if mine counts since I am not using a stock XR10 Chassis. It is about the same size though (roughly)

Sidewinder ESC
CC BEC
Punk Dig
Futaba Rx
Deans and Bullets

Wes
brazwewn is offline   Reply With Quote
Old 01-29-2011, 08:11 PM   #20
I wanna be Dave
 
Join Date: Nov 2007
Location: Memphis
Posts: 4,786
Default

Whoodie Wins


Last edited by helhedded; 01-29-2011 at 08:14 PM.
helhedded is offline   Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -6. The time now is 06:36 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com