|
| LinkBack | Thread Tools | Display Modes |
05-25-2021, 01:26 AM | #1 |
Newbie Join Date: Jun 2020 Location: Norway
Posts: 45
| Team Berberg's 2.2M SuDu Pro XR10 revival
I have always wanted a MOA, and when I recently came across a SuDu Pro XR10 very cheap I jumped on the deal to get a decent entrance in to the 2.2M class It has already been built and driven many years here in Norway. Here it is when I recieved it: Removed the wheels and that awful aluminium roof panel to get a better view of what I'm working with. Its got some really nice parts, but its in desperate need of TLC |
Sponsored Links | |
05-25-2021, 01:31 AM | #2 |
Newbie Join Date: Jun 2020 Location: Norway
Posts: 45
| Re: Team Berberg's 2.2M SuDu Pro XR10 revival
The axles are pretty well built from my understanding, but I disassembled them to give them a health check, swap bearings and grease them again. Lets start with rear axle From my research, these are the specs: - 2 bolt mod - CreeperBob titanium axle shafts - All Axial Machined gears - Titanium upper shaft - Traxxas Oilite small bushing (I replaced this with new oilite) - VP alu transmission housing - Krazed Builds motorplate and upper link mount - BWD Blade stiffener - Axial alu lockouts - Team Brood Creep 35T motor (I timed it to 0 degrees on the rear. Brushes are OK for now, will need new brushes and comm cut soon) - Delrin motor protector Disassembly and check Back together with new bearings, some new bolts and a thorough clean-up! Back together with new rod ends (5347 for lower 4mm and 1942 for upper 3mm). Will attend the shocks later |
05-25-2021, 01:36 AM | #3 |
Newbie Join Date: Jun 2020 Location: Norway
Posts: 45
| Re: Team Berberg's 2.2M SuDu Pro XR10 revival
I then proceeded to do the same thing on the front axle, specs: - All Axial Machined gears - Titanium upper shaft - Traxxas Oilite small bushing (I replaced this with new oilite) - VP alu transmission housing - Krazed Builds motorplate - VP Upper link mount and servo mount - VP C hubs - Dlux brass knuckles - Rowdy Racing battery mount - Team Brood Creep 35T motor First of I started by cleaning the really bad knuckles I removed the slugs inside the knuckles and addifitonal brass ring, as I felt the knuckle provided enough weight itself. I will play around with either Loaded Dice or Pat's weight hanger later on. After new bearings, grease and a new bottom housing, put together again: |
05-29-2021, 12:48 AM | #4 |
Rock Stacker Join Date: Nov 2009 Location: Santa Rosa, CA
Posts: 86
| Re: Team Berberg's 2.2M SuDu Pro XR10 revival
It’s looking good!! Some quality parts there for sure Sent from my iPhone using Tapatalk |
05-31-2021, 01:48 AM | #5 | |
Newbie Join Date: Jun 2020 Location: Norway
Posts: 45
| Re: Team Berberg's 2.2M SuDu Pro XR10 revival Quote:
Yeah, its had a good bunch of upgrades already Swapped out the remaining rod ends, and paired it to my MT-4s and took it for a testdrive. Worked awesome! Made a preliminary roof. Have some KrawlerKonzepts skins on the way Swapped out the front springs with some Dlux springs and printed lower cups. Changed oil to 15wt. May need supersoft springs here, the compression is alot harder than rear Clocked back the C hubs more, straigthened out the tie rod and got a good amount more of steering! Made a set of Skinny Doovers. Made from 1.9 Red Dot Rovers with Voodoo Pin sidewall from some worn out pins. My first cut'n'shut tires other than narrowing VooDoo's Swapped out that worn out Bluebird servo for a Futaba CB700 | |
06-16-2021, 09:09 AM | #6 |
Newbie Join Date: Jun 2020 Location: Norway
Posts: 45
| Re: Team Berberg's 2.2M SuDu Pro XR10 revival
New skins from Krawler Konceptz, really nice with metallic flake |
07-01-2021, 03:08 PM | #7 |
Quarry Creeper Join Date: Jun 2008 Location: Portsmouth UK
Posts: 391
| Re: Team Berberg's 2.2M SuDu Pro XR10 revival
Good to see a new build thread. Truck`s looking good! you had some great parts to start from.
|
09-11-2021, 07:26 PM | #8 |
Tire&Foam Extraordinaire Join Date: Jun 2007 Location: C.I. Compound, Tyler, Texas
Posts: 5,601
| Re: Team Berberg's 2.2M SuDu Pro XR10 revival
Nice build thread full of picturesThank you for sharing your build.
|
09-15-2021, 06:57 AM | #9 |
Newbie Join Date: Jun 2020 Location: Norway
Posts: 45
| Re: Team Berberg's 2.2M SuDu Pro XR10 revival |
09-15-2021, 06:59 AM | #10 | |
Newbie Join Date: Jun 2020 Location: Norway
Posts: 45
| Re: Team Berberg's 2.2M SuDu Pro XR10 revival Quote:
Unfortunately I have only had time to do one comp with this rig so far this year, not sure if this link works, but here is a short video: https://www.facebook.com/717050850/v...9214821325851/ | |
03-10-2022, 10:27 PM | #11 |
Rock Crawler Join Date: Oct 2011 Location: smithville
Posts: 642
| Re: Team Berberg's 2.2M SuDu Pro XR10 revival
Nice build! What shocks are those?
|
05-04-2022, 03:50 AM | #12 |
Newbie Join Date: Jun 2020 Location: Norway
Posts: 45
| Re: Team Berberg's 2.2M SuDu Pro XR10 revival |
Team Berberg's 2.2M SuDu Pro XR10 revival - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Team Berberg's 1.9 Comp rigs | MikaelBerberg | 1.9 Scale Rigs | 23 | 10-04-2021 02:11 AM |
Dravtech Sudu Mod 3d xr10 | convictcrawlers | Axial XR10 | 4 | 10-12-2019 09:48 PM |
DravTech presents the Sudu Pro - 2.2 Pro chassis | Dravpnir | Chassis and Suspension | 59 | 05-03-2016 02:21 PM |
NCD SuDu Pro Down Under... OB New Pro Build. | Oz Bruiser | Axial XR10 | 142 | 10-02-2013 03:50 AM |
| |