Anyone gotten theirs yet? I still have not gotten mine. Paid on the 10th, supposed to have been shipped on the 15th and arrive on the 22nd. Tracking # doesn't tell me anything
<input id="gwProxy" type="hidden"><!--Session data--><input onclick="jsCall();" id="jsProxy" type="hidden">

Thanks for the note. The usa orders are real slow these days going through New Jersey. Wish there was a better way. Some arrive in 5 days, some 3 weeks.

yeah Gula, Canadian orders are a bit different then ours in the U.S. I ship things all the time and sometimes it takes a week and other times its 3 weeks. I trust that Generis shipped yours out, you just have to be patient and I trust its not his fault. just the way the postal services go on both sides of the fence. You also have to take inot account that its when the Customs dept releases the package as well.

It came in two days ago. Just by looking at it the craftsmanship looks superb. I don't have any 5mm 32P gears yet, but should here shortly
<input id="gwProxy" type="hidden"><!--Session data--><input onclick="jsCall();" id="jsProxy" type="hidden">

Order placed! 8)

I hope customs is good to me.

It really didnt take long to get my goodies:
http://i171.photobucket.com/albums/u...d/P1030342.jpg

I got mine in a few days ago and like everyone else has stated the craftsmanship is excellent.. It's a very beefy case in a small package IMO it's one of the best offered.. Hot Racing pinions are a little to tall so you may want to keep that in mind when ordering, I should have gotten the whole thing even though the starter kit is a great idea.

does anyone know if a set of RC4WD punisher2 shafts will fit along side a regular shaft on this? or is it too skinny?

also, is there any "play room" inside the housing? could I possibly put a larger gear and smaller gear to achieve some sort of reduction, albeit not much...or am I stuck with it being 1:1 ratio?

There is no room to change the gearing. If you look at the pictures on the first post, the case has been manufactured to hug the 20t gear within 1mm. Unless you get creative, the gearing is stuck at 1:1.
The shaft sizes that work are up to 5/8 diameter outside. The spacing on the shafts will allow 2 shafts of up to 5/8 inch diameter to be mounted beside eachother. A punisher shaft is just under 1/2 inch, so there's no trouble fitting that in there.

superurb..... that is all"thumbsup"

Just got mine today, took a week, the tracking info said it wouldn't be here for another week, lol. This thing is really nice! Can't wait to get it in and try to break it, not sure if I can though I went with this one because it looked the toughest :D

Hi Chris
Ive received the transfers last friday, very fast shipping and very good stuff man...thanks for your attention

This is the only transfer case anyone should think about buying. 100% one of my top RC products I ever bought, Simply a great product!"thumbsup"
http://i80.photobucket.com/albums/j1...4/IMG_3112.jpg

Just bought one, I'm excited to do a full report on the beef. "thumbsup"

Looks good, how much did you pay?

I'll give you a hint. The price is in this thread.

how much for a complete unit & skid posted to 4132 Australia?
cheers Aaron.

Here's a full listing of the GCM Truck Parts. Every item that's in your cart will contribute to the posting cost (also shown in the cart) and I'm guessing it's about $12 for shipping.

Very nice setup, your kits are frickin sweet too. Awesome!

do u make a kit to work for a HPI wheely king...? the trans.. is weak and i like the t-case setup. would it be possible to run the drive shaft right off the motor then to the t-case with a fast brushless system... or will there not be enough gear to spin the tires.... it going to be a basher/mud truck... with 2.2 tires..

thanks