Berg/Axial Knuckle weights

[Erik D_lux]

Brass knuckle weights. Proudly made in the U.S.A.

Brass knuckle weights to attach to the steering knuckle.

This weight will fit:
Axial brand hi clearance knuckles
VP brand Axial hi clearance knuckles
VP brand Berg hi clearance knuckles
VP brand Axial zero ackerman knuckles (may require light grinding)
RCbros LOSI hi clearance knuckles (mild modification necessary)

WILL NOT WORK WITH STOCK BERG KNUCKLES. ALL AXIAL REFERENCES ARE FOR THE AX10, NOT THE XR10.

Benefits of a knuckle weight system
Less rotating mass
Less broken parts
More wheel speed
More run time per battery
Serious increase in stability
Sidehill, uphill, downhill
Pulls out/does not get into binds like running with wheel weights
Feels MUCH lighter. Feels like it climbs 1000x better

Each knuckle weight is 2.4oz

The weights have been tapped so extra rings can be bolted to them.
Each .100 ring weighs approx .4 oz.
Each .300 ring weighs approx 1.2oz.
Each large diameter ring (goes around the knuckle weight) weighs approx 3.4oz.

Pricing:

Knuckle weight complete setup: (2) Knuckle weights, (4) extra rings and all hardware $83
(2) Knuckle weights $58
(2) Extra .100 rings with hardware $15
(2) Extra .300 rings with hardware $20
(2) Large diameter rings with hardware $20
http://www.dluxfab.com/products

Wheel weight combos:
A Vanquish DH wheel with 585 hubs can use .200 extra rings per side.
A Vanquish SLW wheel with 475 hubs can use .500 extra rings per side.
A Vanquish SLW wheel with 600 hubs can use .600 extra rings per side.
A Vanquish SLW wheel with 725 hubs can use .800 extra rings per side.
A stock Losi LCC/LNC cannot use any extra rings.
Proline Titus wheel with about 1/32" dremel clearancing of the ribs inside the wheel can use .200 extra rings Thanks Shawn M
DNA assassin AX10 offset wheel can use approx .700 extra rings Thanks ShellJeep
A CKRC murdered out wheel can use .400 extra rings per side. Thanks Jslick
A Motoworks (style?) wheel can use .300 extra rings per side. Thanks Jslick

[Erik D_lux]

[mtnhrdgr2]

Looks nice!! What is the diameter and width of the knuckle weight?

[Erik D_lux]

Originally Posted by mtnhrdgr2

Looks nice!! What is the diameter and width of the knuckle weight?

1.5" o.d. and approx .5" i.d.

[NorZepol]

Will these work with Mayhem comp phattys axial wide offset and Vanquish ZA in a BTA setup?

[mtnhrdgr2]

Originally Posted by Erik D_lux

1.5" o.d. and approx .5" i.d.

I totaly forgot about asking the i.d. Thanks for the info. Can you tell me how wide the knuckle weight is?

Basically, I am trying to figure out if it will work with any of my 1.9 wheels.

[Erik D_lux]

Originally Posted by NorZepol

Will these work with Mayhem comp phattys axial wide offset and Vanquish ZA in a BTA setup?

Sorry, I dont have the answers for every setup. The ZA knuckles will fit, even in BTA setup. Almost every wheel out there should work with these. I would guess your Mayhem wheels will work but not allow the use of any rings.

As soon as I get feedback from everybody on what works I will update the thread above with more info on what wheels work with what ring combos.

[Erik D_lux]

Originally Posted by mtnhrdgr2

I totaly forgot about asking the i.d. Thanks for the info. Can you tell me how wide the knuckle weight is?

Basically, I am trying to figure out if it will work with any of my 1.9 wheels.

They should work with 1.9 wheels. I have my Losi ones on my Axial 1.9's.

i.d. is 1" the width will come out close to flush with the backside of the hex.

[Erik D_lux]

I still have about half of the knuckle weights left. I only have enough .100 rings for one more "complete set" then I will be turning that option off until approx next week when I get more in.

Also, you should only need 2- .100 rings per side, ever. After that its much better to order the .300 rings

[Erik D_lux]

And gone....

I will have more .100 rings soon.

[kennyj]

Thanks for the ultra fast shipping. Very nice product!

[Erin]

So these will not work w RCBros zeroack knuckle, correct?

They look real good

[Erik D_lux]

Originally Posted by Erin

So these will not work w RCBros zeroack knuckle, correct?

They look real good

I am not sure. I will see what I can figure out.

[Seth]

Originally Posted by Erik D_lux

Brass knuckle weights.

This weight will fit:

RCbros LOSI hi clearance knuckles (mild modification necessary)

Can you give more details on what modification is necessary? Any pictures of this set up?

I'll be ordering soon !

[Erik D_lux]

Originally Posted by Seth

Can you give more details on what modification is necessary? Any pictures of this set up?

I'll be ordering soon !

Here you go:

RCBros hi clearance knuckle weights

[Seth]

Originally Posted by Erik D_lux

Here you go:

RCBros hi clearance knuckle weights

Outstanding ! Any idea when you will have another batch ready? The website says the complete sets are on hold.

[Erik D_lux]

I have the knuckle weights, just no .100 rings.

I should have some more .100 rings in stock next week.

[CD13]

Just ordered the knuckle weights and the .300's. Who needs the little .100's anyway.

[Erik D_lux]

Originally Posted by CD13

Just ordered the knuckle weights and the .300's. Who needs the little .100's anyway.

Thats what I say, LOL.

Shipped!

[CD13]

Thank you for the fast shipping and responce