Loaded Dice Knuckle weight add ons

[Erik D_lux]

Short and sweet for now so I can avoid answering the same question in PM over and over. As of now, there are too many options so I think I will just take orders through PM.

Please be patient. There are a million options and ways to set these up. Also, since there are a million different versions of wheel faces available, I will have to make them to order. If youre the impatient type, you may want to pass on these.

I need to know:
Delrin or Brass weights
Wheel face style
Wheel face color/material

To run these weights, you MUST run a Dlux knuckle and the NEW Dlux wheels.

[Erik D_lux]

I will have 2 versions of weight holders.

First is a Delrin holder (lower cost, not as much overall weight) as seen in my sporty thread Dlux Sportsman build I dont have an accurate weight just yet but should be 4.5-5oz fully loaded not including the weight of the knuckle.

$30 for the holders, $47 for the tungsten weights (16pcs)



The second version is the brass version (heavier and more expensive) as seen in the Berg section Dlux Berg Build I believe these weights came in close to 6oz full of tungsten.

$80 for the holders, $47 for the tungsten weights (16pcs)

[Erik D_lux]

I top off the brass weight holder with another big brass ring. This thing weighs a full 1.7oz by itself and should get you really close to 8.5oz fully loaded with the brass holders and full tungsten weights

$30 for the pair.

[Erik D_lux]

Wheels.....

Due to the custom nature of these wheels there will be no exchanges or refunds.

I can make the face from G10 or Carbon fiber. I only went with G10 to get some color on my car (sick of full CF look).

Black G10 set of 4 $60

Any color you want G10 set of 4 $75 See here for colors G10 Colors & Textures - AKS™ Alpha Knife Supply G10 Material Colors. Maybe a wait time if I have to order the color in.

Carbon fiber set of 4 $80

All wheels will be shipped as 3/4" wide wheels. I measure BETWEEN the tire beads. I can go larger on special request and can do 5/8 wide too. Be aware that 5/8 version is harder to setup and fit

Face styles (in order below):

5 Star

Rising sun

V cut

D cut

Slug

Stars

[Erik D_lux]

How to assemble the wheels:

Check this YouTube video for instructions on how to install the weights and also how to assemble the wheels. Starting at 3:55

https://youtu.be/1VbVoj3RiFo

[saniel68]

Very nice. Are the tungsten weights the same dia. as the ones offered by Derby Monkey?

[Session]

Could you show how the wheels work or go together? Is it like a bead lock but from the inside or are they glue on?

Off topic, Yay post 50. I am not a freaking newbie anymore

[Erik D_lux]

Originally Posted by saniel68

Very nice. Are the tungsten weights the same dia. as the ones offered by Derby Monkey?

Yep, they are the Derby weights.

Originally Posted by more_session_please

Could you show how the wheels work or go together? Is it like a bead lock but from the inside or are they glue on?

Off topic, Yay post 50. I am not a freaking newbie anymore

They are all glue on, inside and out. I will try to get some pics of how they work when I get a shot. You will need to slightly modify your tires too which will make them so they can never be used as a bead lock again, only glue ons.

[Wicked Monkey]

Those brass holders with the Tungsten weights are pure sex.

[Session]

Originally Posted by more_session_please

Could you show how the wheels work or go together? Is it like a bead lock but from the inside or are they glue on?

Originally Posted by Erik D_lux

They are all glue on, inside and out. I will try to get some pics of how they work when I get a shot. You will need to slightly modify your tires too which will make them so they can never be used as a bead lock again, only glue ons.

Still waiting Sir.........I have some guesses but now its starting to gnaw at my little brain

[Harvo]

Originally Posted by more_session_please

Still waiting Sir.........I have some guesses but now its starting to gnaw at my little brain

It's easy once you have them in your hands. I don't think he wants to show too much on line until you get them because they are pretty proprietary.

[Session]

Originally Posted by Harvo

It's easy once you have them in your hands. I don't think he wants to show too much on line until you get them because they are pretty proprietary.

Mr D said he was going to post some pic's so I had no idea they were classified.......There is no way another vendor would make something almost exactly the same would they?

[Erik D_lux]

Originally Posted by more_session_please

There is no way another vendor would make something almost exactly the same would they?

I am not too worried about it. My biggest problem right now is that I am consistently trying to get caught up. Just a matter of priority and orders have a bigger priority than these pictures. Sorry. I promise I will get to them ASAP, I have have to since the first batch of these weights shipped today.

[gooserools]

Question. I got The brassholder with tungsten wheights. But cant get The wheights in the holes they are slighty to big. So how do i get them in place? Heat and freeze?

[Erik D_lux]

They are made for a press fit. When I install them I use a hammer and a punch to drive them in. I hope that helps.

[Drew3627]

just a suggestion freeze the tunsgton and place the brass in hot water,they will come together snuggly and when at room temp are tight. work for me

[FLOKI-81]

same wheel.system as I got,,,
The carbonfiberwheels that was held together by a nut is what came along the axels when I bought em,,,,I also got some G10 with 6 holes like the revolver consept...

[FLOKI-81]

does the loaded dize weightsystem fit in youre carbonfiber D cut 2.2 wheels,,and V cut wheels,,
And do you have other carbonfiber wheels that the loaded dize fit inside,,
PS,,, Have a merry merry X-MAS!!!!!!!

[Erik D_lux]

I think all of your questions have already been answered in this thread? If not, let me know which ones you do not see.

Merry Xmas to you, Floki.

[FLOKI-81]

Do you make the V cut spokes in carbonfiber???