|
| LinkBack | Thread Tools | Display Modes |
04-05-2014, 10:05 AM | #41 |
RcBros Hobbies Join Date: Nov 2005 Location: Oregon
Posts: 4,646
|
Rear tubes, including protos for DLux shafts are done. Once we get back from Easter jeep safari these will be available. Sent from my iPhone using Tapatalk |
Sponsored Links | |
04-05-2014, 09:41 PM | #42 |
Rock Crawler Join Date: May 2008 Location: The Beautiful South
Posts: 617
| Re: RcBros Front and Rear Berg Tubes
so if I get these tubes, and vanquish c hubs, and vanquish knuckles, what axle shafts do I use? Stock dogbone and outdrive? Will that work? Are there some drop in cvd's available? I'm not into the custom made stuff. When something breaks I want to be able to buy another and put it right in. Can this be done? Thanks. |
04-05-2014, 10:39 PM | #43 |
Newbie Join Date: Jun 2013 Location: Portland
Posts: 16
| Re: RcBros Front and Rear Berg Tubes
The short answer is no, not the stock axles. Check out Will's post #18 in this thread,he says SDS300 HD or the Dlux shafts. Good luck finding the SDS's he has not posted in quit a while. The Dlux shafts have a large tang on them and come with a locker to fit them, and are very strong. They are made to allow up to 70 degrees of steering,more than most setups can use. I have Erik's shafts in my berg and they work very well IMO. Good luck in your quest : Mike |
04-06-2014, 07:09 AM | #44 |
Rock Crawler Join Date: May 2008 Location: The Beautiful South
Posts: 617
| Re: RcBros Front and Rear Berg Tubes
^thanks for that answer. If the dlux shafts are strong enough that they won't bend every time my crawler falls off the rocks, that may be a viable option.
|
04-10-2014, 10:06 PM | #45 |
RcBros Hobbies Join Date: Nov 2005 Location: Oregon
Posts: 4,646
| Re: RcBros Front and Rear Berg Tubes
Rear tubes are in stock and shipping after we get back from moab. I'm looking for two testers for the Dlux shaft versions. PM me with why you deserve them. My requirements are you must have a good camera and provide real feedback.
|
09-23-2014, 09:08 PM | #46 |
RcBros Hobbies Join Date: Nov 2005 Location: Oregon
Posts: 4,646
| Re: RcBros Front and Rear Berg Tubes Prices Have Been Slashed, come check out the sale! We also have custom Offset truely center super tubes putting your supers at 13.5" with with a flat faced wheel and Zero Scrub PM for details. Also 7980 Servo Mounts for the super tubes! |
12-20-2014, 05:06 PM | #47 |
RcBros Hobbies Join Date: Nov 2005 Location: Oregon
Posts: 4,646
| Re: RcBros Front and Rear Berg Tubes
Still in stock!
|
03-26-2017, 12:43 PM | #48 |
RcBros Hobbies Join Date: Nov 2005 Location: Oregon
Posts: 4,646
| Re: RcBros Front and Rear Berg Tubes
Bump this up!! Still have some in stock.
|
06-06-2017, 07:06 PM | #49 |
Pebble Pounder Join Date: May 2015 Location: The Rocky maintains
Posts: 110
| Re: RcBros Front and Rear Berg Tubes
Do Berg VP universals/CVD's work with your Front tubes?
|
06-07-2017, 09:08 AM | #50 |
RcBros Hobbies Join Date: Nov 2005 Location: Oregon
Posts: 4,646
| Re: RcBros Front and Rear Berg Tubes |
06-10-2017, 03:34 AM | #51 |
Pebble Pounder Join Date: May 2015 Location: The Rocky maintains
Posts: 110
| Re: RcBros Front and Rear Berg Tubes
I believe they are VP berg universals. They may have been discontinued. I'm not 100% sure, they came with the berg axle I purchased used. They fit great with axial ax-10 chub and VP high steer knuckle. The inner bearing is square with the axle tube.
|
RcBros Front and Rear Berg Tubes - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Rcbros tubes with creeperbob ti axles for Berg | huskerfan406 | Newbie General | 3 | 06-26-2013 02:15 PM |
| |