Go Back   RCCrawler Forums > Vendors > Vendors Market > Axles, Trannys, T-case
Loading

Notices

Thread: **AX10/SCX10 Housing Splined Burly Tubes**

Reply
 
LinkBack Thread Tools Display Modes
Old 12-02-2013, 07:34 PM   #21
RCC Addict
 
Join Date: Nov 2011
Location: Surrey,BC- Canada
Posts: 1,663
Default Re: **AX10/SCX10 Housing Splined Burly Tubes**

Got my set yesterday
Very nice looking
I went to install them and I can,t get the c-hub to slide all the way on
It slide till it runs out of splines inside the c-hub which leave about a 1/8th of beef tube spline showing between the caller and c-hub.

I will take a picture to post when I get home
chevotafun is offline   Reply With Quote
Sponsored Links
Old 12-02-2013, 07:36 PM   #22
RcBros Hobbies
 
RcBro's Avatar
 
Join Date: Nov 2005
Location: Oregon
Posts: 4,646
Default Re: **AX10/SCX10 Housing Splined Burly Tubes**

LMK what brand Chub you are using please. I'll do what I can to help. I just spot checked a few more with no bad results. We will see what we can do to get you fixed up.
RcBro is offline   Reply With Quote
Old 12-02-2013, 07:56 PM   #23
Rock Stacker
 
Join Date: Mar 2013
Location: Victoria
Posts: 88
Default Re: **AX10/SCX10 Housing Splined Burly Tubes**

Any chance you'll make some for Wraith axles?

Pretty please?
Bluebox is offline   Reply With Quote
Old 12-02-2013, 08:18 PM   #24
RCC Addict
 
Join Date: Nov 2011
Location: Surrey,BC- Canada
Posts: 1,663
Default Re: **AX10/SCX10 Housing Splined Burly Tubes**

Quote:
Originally Posted by RcBro View Post
LMK what brand Chub you are using please. I'll do what I can to help. I just spot checked a few more with no bad results. We will see what we can do to get you fixed up.
Vp c-hubs
I will take a couple picture when I can get back down to the garage

Yeah doesn't make sense to me either I'm sure it's something small
chevotafun is offline   Reply With Quote
Old 12-03-2013, 08:05 PM   #25
Newbie
 
Join Date: May 2013
Location: Canada, BC
Posts: 22
Default Re: **AX10/SCX10 Housing Splined Burly Tubes**

Did you get this figured out?
JacksonTrix is offline   Reply With Quote
Old 12-03-2013, 08:19 PM   #26
RcBros Hobbies
 
RcBro's Avatar
 
Join Date: Nov 2005
Location: Oregon
Posts: 4,646
Default Re: **AX10/SCX10 Housing Splined Burly Tubes**

Quote:
Originally Posted by JacksonTrix View Post
Did you get this figured out?
The fitment on his ended up being very tight, he was able to get them on and off, but it wasn't without using some force. I'm not sure why to be honest, but after a few on and offs they should fit tight but be able to come off by hand.
RcBro is offline   Reply With Quote
Old 12-04-2013, 09:18 PM   #27
RcBros Hobbies
 
RcBro's Avatar
 
Join Date: Nov 2005
Location: Oregon
Posts: 4,646
Default Re: **AX10/SCX10 Housing Splined Burly Tubes**

Just added the colors to our cart system. Hope to get pictures up when I get caught up!
RcBro is offline   Reply With Quote
Old 12-12-2013, 12:34 PM   #28
Newbie
 
Join Date: May 2013
Location: Canada, BC
Posts: 22
Default Re: **AX10/SCX10 Housing Splined Burly Tubes**

So is it confirmed that for the rear you can run wraith lock outs and long side wraith shafts so track width is same as the front with the xr steering?
JacksonTrix is offline   Reply With Quote
Old 12-14-2013, 11:53 PM   #29
Rock Crawler
 
Join Date: Oct 2011
Location: Lake Worth
Posts: 748
Default Re: **AX10/SCX10 Housing Splined Burly Tubes**

Got mine started
bagged86 is offline   Reply With Quote
Old 12-15-2013, 08:48 AM   #30
Rock Crawler
 
Join Date: Nov 2011
Location: Sin City
Posts: 820
Default Re: **AX10/SCX10 Housing Splined Burly Tubes**

Quote:
Originally Posted by JacksonTrix View Post
So is it confirmed that for the rear you can run wraith lock outs and long side wraith shafts so track width is same as the front with the xr steering?
The problem with this is the axle shafts. If you use Wraith Lockouts which shafts do you pair with them to get the correct length? Not the XR shafts. The wheely king shafts are one but I'm not sure which lockouts they work with. This is similar to my question in the previous posts. I'm curious to see how this shakes out. A clean and simply XR width conversion would be nice to have.
JHTreyIII is offline   Reply With Quote
Old 12-15-2013, 11:13 AM   #31
I wanna be Dave
 
Join Date: May 2007
Location: Fairfield ME
Posts: 3,886
Default Re: **AX10/SCX10 Housing Splined Burly Tubes**

The lightest option is to leave the rear axle stock and run flipped wheels in the back.
Calderwood is offline   Reply With Quote
Old 12-15-2013, 11:25 AM   #32
RcBros Hobbies
 
RcBro's Avatar
 
Join Date: Nov 2005
Location: Oregon
Posts: 4,646
Default Re: **AX10/SCX10 Housing Splined Burly Tubes**

Quote:
Originally Posted by Calderwood View Post
The lightest option is to leave the rear axle stock and run flipped wheels in the back.
For you sporty guys, this is the go to ticket.

For the scalers and those who dont like this option, I'm sorry this is taking so long.

I'm pretty sure the Wraith rear locker and XR10 long rear shaft is the ticket. However, I cannot confirm till I get some rear lockouts in hand.

I just installed the XR10 rear lockout on our Burly tubes out back with XR10 rear short shafts. This combo bolts together, however is still not equal track width.
RcBro is offline   Reply With Quote
Old 12-15-2013, 01:08 PM   #33
Rock Crawler
 
Join Date: Nov 2010
Location: the 'burgh'
Posts: 976
Default Re: **AX10/SCX10 Housing Splined Burly Tubes**

Is it close to the same & how much wider than the stock SCX width??

Thanks for your insight.
gdb85 is offline   Reply With Quote
Old 12-15-2013, 03:49 PM   #34
RCC Addict
 
Join Date: Oct 2005
Location: rite here all along
Posts: 1,888
Default Re: **AX10/SCX10 Housing Splined Burly Tubes**

Can you make some that do not have the extra collar area so the splines end at the shock mount? I want the advantage of the steering without the width
halfcab is offline   Reply With Quote
Old 12-15-2013, 04:51 PM   #35
Rock Crawler
 
Join Date: Oct 2011
Location: Lake Worth
Posts: 748
Default Re: **AX10/SCX10 Housing Splined Burly Tubes**

I put together the rear lastnight and to make the width you need burley tubes and wraith lockouts.
bagged86 is offline   Reply With Quote
Old 12-16-2013, 05:22 PM   #36
Newbie
 
Join Date: May 2013
Location: Canada, BC
Posts: 22
Default Re: **AX10/SCX10 Housing Splined Burly Tubes**

Quote:
Originally Posted by bagged86 View Post
I put together the rear lastnight and to make the width you need burley tubes and wraith lockouts.

And what shafts?
JacksonTrix is offline   Reply With Quote
Old 12-16-2013, 09:14 PM   #37
RcBros Hobbies
 
RcBro's Avatar
 
Join Date: Nov 2005
Location: Oregon
Posts: 4,646
Default Re: **AX10/SCX10 Housing Splined Burly Tubes**

Hey Guys, If your wanting equal track width, a set of burly tubes in back is required along with wraith lockouts and XR10 rear long shafts, there are several vendors who can cut you 2 long XR10 Shafts. If you are using these for a sporty with a flat faced wheel, you can easily flip the wheel for equal track width.

I am working on an option for you stock width guys, and hope to have a how-to up by the end of the week.
RcBro is offline   Reply With Quote
Old 12-16-2013, 09:49 PM   #38
RcBros Hobbies
 
RcBro's Avatar
 
Join Date: Nov 2005
Location: Oregon
Posts: 4,646
Default

Alright, for those guys wanting a 7075 burly tube but want to retain your stock width, here's what you need to do.

First cut 12mm off your burly tube.


Then cut your axle halves flush with the link mounts. At this point your burly tube fits right in.


You will still need to drill and tap the burly tube, but now you have a killer burly tube upgrade.
RcBro is offline   Reply With Quote
Old 12-24-2013, 08:45 AM   #39
RCC Addict
 
Join Date: Mar 2010
Location: RC Addict Garage
Posts: 1,004
Default

Any one have a picture compared to a stock scx10 axle and a sock wraith axle?

Sent from my HTC6435LVW using Tapatalk
Tin Soldier is offline   Reply With Quote
Old 12-31-2013, 08:35 AM   #40
Quarry Creeper
 
Join Date: Dec 2012
Location: Seattle
Posts: 274
Default Re: **AX10/SCX10 Housing Splined Burly Tubes**

Quote:
Originally Posted by RcBro View Post
Alright, for those guys wanting a 7075 burly tube but want to retain your stock width, here's what you need to do.

First cut 12mm off your burly tube.

Then cut your axle halves flush with the link mounts. At this point your burly tube fits right in.

You will still need to drill and tap the burly tube, but now you have a killer burly tube upgrade.
So for myself to run wraith lockouts, I just need one more set (follow directions), and it will all work?
fatroofus is offline   Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -6. The time now is 12:02 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com