|
Krazed Builds - Carbon Fiber XR10 Motor/Gear Plates http://i208.photobucket.com/albums/b...psafvui9kf.png They're Here! Krazed Builds brings you Carbon Fiber gear plates for your XR10. For those looking to shed some weight, those looking for a Vp alternative or those looking for a little bling .... These are them. http://i208.photobucket.com/albums/b...ps4ekbcf2u.jpg All plates take the Bigger bearings like a Vanquish plate for that added extra toughness. They fit right in to a Stock case, RC4wd case and the Vanquish case .... no modifications needed. You will need: (2) 5x10x4 flanged bearings 5x10x4 (FLANGED) Rubber Sealed Bearing MF105-RS (1) 5x9x3 flanged bearing 5x10x4 (FLANGED) Rubber Sealed Bearing MF105-RS ... for EACH plate. But for those of you with stock bearings or wishing to shed even a little more and want the stock bearings We Can cut separately for you. Just let us know and we can get those together. XR10 Carbon FIber Motor Plates Back in Stock !!!!! |
Re: Krazed Builds - Carbon Fiber XR10 Motor/Gear Plates Important Installation Note The Vp plate modifies the screw location for your upper link mounts. It brings a button head screw to be flush with the top of the flanged bearing. We changed this on ours. We countersink the 3mm screw hole there so a countersunk screw is used and sits below that flange. Doing this causes the head of the screw to interfere with the bearing due to its location. you will need to file the screw head a little where it sites inside the bearing hole to allow the bearing to sit in properly. Failing to do this will not allow the bearing to seat properly causing misalignment and possible bearing failure. Below is a picture showing where to file http://i208.photobucket.com/albums/b...psftjx8rpo.jpg After its filed and bearing is seated http://i208.photobucket.com/albums/b...psidzw44pc.jpg |
Re: Krazed Builds - Carbon Fiber XR10 Motor/Gear Plates More photos and weight comparisons. http://i208.photobucket.com/albums/b...psljjmhq0e.jpg http://i208.photobucket.com/albums/b...psooqy5teu.jpg http://i208.photobucket.com/albums/b...psjnfacdb9.jpg Stock Axial Motor Plate http://i208.photobucket.com/albums/b...psr5dbmwet.jpg Vanquish Plate for beg bearings http://i208.photobucket.com/albums/b...psj4fn36hv.jpg Krazed Builds Carbon Fiber Plate http://i208.photobucket.com/albums/b...psrmfcsadr.jpg No more swiss cheesing your motor plates to drop the weight "thumbsup" |
Re: Krazed Builds - Carbon Fiber XR10 Motor/Gear Plates But, I like cheese! Nice work. "thumbsup" |
Re: Krazed Builds - Carbon Fiber XR10 Motor/Gear Plates Quote:
:mrgreen: Thanks. |
Re: Krazed Builds - Carbon Fiber XR10 Motor/Gear Plates are compatible with the case HR? I did not understand how many plates are necessary for completaew an axle ... |
Re: Krazed Builds - Carbon Fiber XR10 Motor/Gear Plates Quote:
Yes - the HR case fits on a stock Axial plate so these will fit right in. 1 plate per axle - each set is 2 plates so you can do your front and rear axles in one shot. If you are using their plate then the bearings will drop right in also. Hope that helps. |
Re: Krazed Builds - Carbon Fiber XR10 Motor/Gear Plates Second batch in stock - Ready to ship! "thumbsup" |
Re: Krazed Builds - Carbon Fiber XR10 Motor/Gear Plates I will soon place an order ;) |
Re: Krazed Builds - Carbon Fiber XR10 Motor/Gear Plates Quote:
Ready to ship "thumbsup" |
Re: Krazed Builds - Carbon Fiber XR10 Motor/Gear Plates Pay Pal sent "thumbsup" |
Re: Krazed Builds - Carbon Fiber XR10 Motor/Gear Plates Quote:
"thumbsup" Will go out today. Thanks. |
Re: Krazed Builds - Carbon Fiber XR10 Motor/Gear Plates More in stock - Ready to ship "thumbsup""thumbsup" |
Re: Krazed Builds - Carbon Fiber XR10 Motor/Gear Plates 6 sets left - Probably wont do another run of these unless the XR makes a come back. Been a great product run. Nothing wrong with them - just slowed down enough that we think its time to blow the rest out. $50 a pair Shipping U.S.P.S. Priority in the U.S. is included International including Canada is available same U.S.P.S. International Priority International Shipping available w/customs number |
Re: Krazed Builds - Carbon Fiber XR10 Motor/Gear Plates I'm really glad I grabbed a pair of these before they ran out! I'm totally impressed with the quality of these and the link mounts. Top notch man!"thumbsup" |
Re: Krazed Builds - Carbon Fiber XR10 Motor/Gear Plates Quote:
|
Re: Krazed Builds - Carbon Fiber XR10 Motor/Gear Plates 5 sets in stock ready to ship "thumbsup" |
Re: Krazed Builds - Carbon Fiber XR10 Motor/Gear Plates free bump everyone needs these Sent from my SAMSUNG-SM-G870A using Tapatalk |
Re: Krazed Builds - Carbon Fiber XR10 Motor/Gear Plates Small batch back in stock - Probably gonna be the last batch for a while with all the other projects we got coming and projected. Supports been great for these. Thank you everyone! "thumbsup" |
Re: Krazed Builds - Carbon Fiber XR10 Motor/Gear Plates Still some left in stock .......... Last batch for a while on these as our focus is turning towards other axles. "thumbsup""thumbsup" |
| All times are GMT -6. The time now is 06:17 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com