TorqueMaster Outdrives for Axial Transmissions

[hotwheels000]

Love mine !!!!!!

A little review and a lot of abuse, no issues at all so far

Holmes Hobbies Torquemaster outdrive / spool review

Thank JRH

[maslin]

6mm Wraith version ordered

Can't keep the RRP one piece lowers from ripping the rear off. This should solve it

[JohnRobHolmes]

I think you might be one of the first to order 6mm We have some huge power being run through 5mm versions without a failure yet. The RR one part lower gear is made nice, but the gear blank material is not good chromoly.



Just wanted to report our Wraith and SCX stock style shafts have been most popular, time to set the machine back up for em so we don't run out!

[maslin]

RRP gear isn't compatible....

The "small" side of the gear will not fit over either flange.


Time to grind on some shiny new parts

Turned down the OD of the shaft just slightly, RRP gear fits great. Handed to my coworker who says "why's there a chunk missing right where it breaks?"

So... Run it, it has a warranty anyway? Or send it back now?

[JohnRobHolmes]

What part number RRP gear? It is listed that only AX/ SCX lower gears are compatible, the wraith lower is known as incompatible. I am running lockrings right now, and have made the diameter smaller to help with fitment of the RRP anodized alloy gear. They fit just fine with Axial and Hot racing gears as-is.

[maslin]

Chucked in a hand held drill and polished with some emery cloth for 20 minutes or so. The pin goes in fine. I had the 1552 gear already, it was really really close, so I polished it 100 grit emery till it cleared.

Just checked the pin again, goes through fine on that side, won't go through on the short side, 3-4mm from passing though.





Edit again. Ran a 3/32 drill bit through the short side, pins goes though fine. I'm going to run it, what's the worst that can happen

And I would like to add, this thing is beefy, should hold up to all the abuse your 3300kv trailmaster can throw at it.


I'm batting 1000 on this thing... Need a 6mm rear output bearing too. Front one is good to go. 6x11x4... odd bearing I can only get online

[fshnut007]

On the extended shaft for the scx10 tranny, how much longer is the shaft over the stock length?

[maslin]

Beefy

[Correll]

That guy with the wraith is pretty crazy. Guess they will have to make some 8mm outputs when he grenades those 6mm's. That second truck to jump looked pretty sweet tho!

[Bananaclip]

Ordered a six hole standard 5mm scx10 chromo limited edition for my dinky delrin splitskid just now from rpp. 15% off for the weekend

[1.55Yota]

Can you make one with 8mm outputs?

[JohnRobHolmes]

Originally Posted by 1.55Yota

Can you make one with 8mm outputs?

I could, but won't be doing it unless it is a very limited run. At this time we are only producing 5mm outputs. What driveshafts would you use with 8mm?

[Lanky]

Any idea of when the scx10 extended outdrives will be back in stock?

[JohnRobHolmes]

We should have warehoused stock that just needs to be packaged. Check back monday.

[Teng]

Originally Posted by JohnRobHolmes

We should have warehoused stock that just needs to be packaged. Check back monday.

When these back in stock again? As I've had log-in my Amainhobbies's account to receive a notification when this item arrives in stock for long time already and yet still in back order.
https://www.amainhobbies.com/holmes-...vetmex/p477885

Would like to order one of my Wraith around the Christmas time