Sacramento Scaler GTG/Comps

[Natedog]

BEC....you need it and it's only another $25 lol....seriously though that is one place you can't skimp.

[stevew]

Originally Posted by Natedog

That depends on your wallet LOL>

well i have a wallet because I'm cheap LOL

Originally Posted by dirty530crawlers

Definetly get a bec for it the best 25$ someone could spend in my opinion. I'm in Lincoln so not too far

well if i only run a 2cell i should be ok without the bec correct?

[Natedog]

LOL

Yes, but it would be better with the BEC that way you get the power to the servo that it needs under load.

[stevew]

Originally Posted by Natedog

LOL

Yes, but it would be better with the BEC that way you get the power to the servo that it needs under load.

great because I think ill wait for a bec right now.my problem is a buy to much stuff and work on it for ever and get bored with it too quick.it happened on my first samurai.
I bought it for $700 with brand new bfg 31's and wheels it only needed a carb so before i found one i started the spoa.got it done. then i found my carb but eneded up buying a 16v,auto trans,rear end,front diff from the guy for $1600 then i started the axle swap again got it all done.then I found a suspension kit local for real cheap $600 so i added that. then i found an 85 toy for $400 and swapped out the axles again.I had spent close to $5k in about 3 months on this project and never drove it ever.

so i try and play with my toys first then upgrade them.

[Jrob]

I had some of the most fun crawlin with my stock ax10 and a 3300mah nimh. Still had those things on the radios then.what r they called oh yea anteners! Lol get that baby driving! And come crawl!

[stevew]

Originally Posted by dirty530crawlers

I had some of the most fun crawlin with my stock ax10 and a 3300mah nimh. Still had those things on the radios then.what r they called oh yea anteners! Lol get that baby driving! And come crawl!

yup just spent another $42 at the local HS spent more on 900 piece nut,bolt,washers from back home.looking at servos again buying bearing for the tlt axles. wow money goes fast when your having a good time.oh wait im not having fun yet.
just spent another $142 on my 7980th
spent another $45 on steel yokes and bearings LOL

[Jrob]

Originally Posted by stevew

yup just spent another $42 at the local HS spent more on 900 piece nut,bolt,washers from back home.looking at servos again buying bearing for the tlt axles. wow money goes fast when your having a good time.oh wait im not having fun yet.
just spent another $142 on my 7980th
spent another $45 on steel yokes and bearings LOL

And the smile on your face when crawlin a bad ass line priceless! Lol

[stevew]

Originally Posted by dirty530crawlers

And the smile on your face when crawlin a bad ass line priceless! Lol

bought 2 of these i wanted something small
HobbyKing R/C Hobby Store : ZIPPY Flightmax 2000mAh 2S1P 45C (USA Warehouse)

[Jrob]

Originally Posted by stevew

bought 2 of these i wanted something small
HobbyKing R/C Hobby Store : ZIPPY Flightmax 2000mAh 2S1P 45C (USA Warehouse)

Nice! The price was rite also

[stevew]

Originally Posted by dirty530crawlers

Nice! The price was rite also

wanted some more mah but they are monster's

[stevew]

ok need some radio help.
needs to be cheap,3ch,3 pos switch and epa's please

[Natedog]

Originally Posted by stevew

ok need some radio help.
needs to be cheap,3ch,3 pos switch and epa's please

FlySky FS-GT3B Digital 3ch 2.4ghz TX & RX LCD Transmitter & Receiver

GT3B Hack Question and Answer Thread

and extra rx are about $7 each.

[zonkerd]

dx3e on CL for 40 $with rx . i run them on all my rigs work great

[Jrob]

Originally Posted by zonkerd

dx3e on CL for 40 $with rx . i run them on all my rigs work great

That's a great deal also!

[Natedog]

Originally Posted by zonkerd

dx3e on CL for 40 $with rx . i run them on all my rigs work great

Of course Flysky comes with rx, I was just pointing out cost savings (spare rx for Spektrum is $35.) Flysky also has 10 model memory, digital trims (not pots), etc.

Key Features
- Model Memory
- Servos NOR/REV
- Steering Trim
- Throttle Trim
- Dual Rate
- End Point
- ABS Settings
- EXP Settings
- Trainer Port (for VRC)
- CE & FCC certified

Specification
- Channels : 3 Channels
- Model type : car/boat
- RF range : 2.40-2.48GHz
- Bandwidth : 500Hz
- Band : 160
- RF power : less than 20DB
- 2.4G system : AFHDS
- Code type : GFSK
- Sensitivity : 1024
- Low voltage warning : yes(less than 9V)
- DSC por t: yes(3.5mm:output:PPM)
- ST range : 90
- TH range : 45(F:30;B:15)
- Charger port : yes
- Power : 12V DC(1.5AA*
- Weight : 328g
- ANT length : 26mm
- Size : 159 x 99 x 315mm
- Color : black
- Certificate : CE,FCC

Includes :
- 1 x 2.4Ghz transmitter
- 1 x 2.4Ghz Receiver
- 1 x Bind Plug
Download PDF Manual: Click Here http://site.hobbypartz.com/manual/FS-GT3B-Manual.pdf

[stevew]

flysky sounds pretty sweet i looked at it but im not real radio savvy.

[stevew]

ok thats ordered LOL now i play the waiting game

[Hoosierdady]

Originally Posted by dirty530crawlers

If you have beef I will see ya around an gladly squash it! Go back to Rcbashers and cry to them we don't need it here

Uncalled for. Just sayin.

[Jrob]

We had an awsome crawl session tonight, thanks to my man zonkered and Dd for bringing another load to the compound. Not to much more and it's gonna be insane. Lol here are a few pics. And thanks again guys our crawl spot is gonna be sweet! And couldn't be done with out you! Time to bring the good old Gtg back more often

[KBess1110]

Had a blast tonight! Thanks for the BBQ Mr dirty530


Sent from my VZW Rezound