RCCrawler Forums

calyakker · 12-13-2006, 08:05 PM

Payment sent for knuckles and bearings.

raytard · 12-14-2006, 01:39 AM

Here's a close up of one of my new knuckles & bearings.

Thanks again R2JP'n!

run2jeepn · 12-14-2006, 02:08 AM

Looks Killer. Thanks for the pic Raytard

Trikster · 12-14-2006, 02:24 PM

Are these side specific like the stockers? I am not using aftermarket C's.

run2jeepn · 12-14-2006, 05:02 PM

These are stock replacement parts. They fit everything the stockers fit just made out of different material.

rcjunky3 · 12-14-2006, 10:48 PM

mine came a week or so back and they are very nice just waitin on axle c's to install them all together

calyakker · 12-21-2006, 04:13 PM

Got the bearings and knuckles today. Very nice finish on these knuckles. I'm impressed. Thanks

Trikster · 12-21-2006, 06:23 PM

Mine finally came in, thanks for the parts! They look really nice. I was looking the knuckles over and it looks like the ones I have are side specific, one post is higher than the other one. Is this what the washers are for?

run2jeepn · 12-21-2006, 11:17 PM

Quote:

Originally Posted by Trikster

Mine finally came in, thanks for the parts! They look really nice. I was looking the knuckles over and it looks like the ones I have are side specific, one post is higher than the other one. Is this what the washers are for?

They are side specific. You can use the washers if you want but I don't they aren't needed. For fact that is something new they added to the pack. Not sure way. The last 160 sets I have sold didn't have them.

Trikster · 12-21-2006, 11:19 PM

They look fantastic though, cannot wait to polish them up to match my Bruiser frame I have about 15 hours into polishing. I can shave looking into the frame...

Cloak · 12-22-2006, 12:04 AM

I might have just hit a quality control issue on mine, but I've had to rethread 2 of the 6 I've opened so far (of

. Not a big deal at all, but just thought you might want to know. The holes are cut exactly where they should be, but the threads themselves were pretty rough and wouldn't let me start the screw. Once I cleaned it up, it threaded perfectly and they turn smooth as butter.

I think you've got me convinced that I *need* them on my other trucks now.

run2jeepn · 12-23-2006, 06:01 AM

I;m running low again on Knuckles and bearing so if you need any soon. Need to place your orders while I still have them. Once again not sure when the next batch will be in.

run2jeepn · 12-26-2006, 08:18 PM

Just sold a few more. I have about a dozen left.

run2jeepn · 12-27-2006, 01:18 PM

I only have 3 sets left....These need to go as always....I'm trying to place another order for more as we speak....Just haven't heard back from them yet. So if you need a set order now....I will take pre-orders for the next batch if you wouldn't mind wating around a week to get them.

Rat1 · 12-27-2006, 01:32 PM

Well i am going to need a set of knuckles and Cs for my TLT real soon. Hope you still have a enough next week or so.

run2jeepn · 12-27-2006, 01:43 PM

Quote:

Originally Posted by Rat1

Well i am going to need a set of knuckles and Cs for my TLT real soon. Hope you still have a enough next week or so.

I may not...So if you need them next week you need to place order Now.. In the last 3 months I have sold over 300 sets. They go Fast...But I can hold you a set from the next order.

MuddKnuckle · 12-27-2006, 02:09 PM

Payment sent for knuckles
Thanks

run2jeepn · 12-27-2006, 02:31 PM

Quote:

Originally Posted by MuddKnuckle

Payment sent for knuckles
Thanks

Got it. They will go out in the Morning.

Only 2 sets left of Knuckles..........:-(

hlpressley · 12-27-2006, 02:37 PM

You better get em' while you can guys. You can't beat his service or price! He is a great guy on top of that.

clodstall · 12-27-2006, 02:56 PM

waiting on money at the moment. if i get it in time i will order these also.

12-14-2006, 01:39 AM	#102
raytard RCC Addict Join Date: Sep 2005 Location: ...Here & There Posts: 1,590	Here's a close up of one of my new knuckles & bearings. Thanks again R2JP'n! Attached Images

12-13-2006, 08:05 PM	#101
calyakker Pebble Pounder Join Date: Dec 2006 Location: Peoria, AZ Posts: 162	Payment sent for knuckles and bearings.

12-14-2006, 02:08 AM	#103
run2jeepn I wanna be Dave Join Date: Sep 2005 Location: USA Posts: 11,196	Looks Killer. Thanks for the pic Raytard

12-14-2006, 02:24 PM	#104
Trikster RCC Addict Join Date: May 2006 Location: Roseville Posts: 1,469	Are these side specific like the stockers? I am not using aftermarket C's.

12-14-2006, 05:02 PM	#105
run2jeepn I wanna be Dave Join Date: Sep 2005 Location: USA Posts: 11,196	These are stock replacement parts. They fit everything the stockers fit just made out of different material.

12-14-2006, 10:48 PM	#106
rcjunky3 RCC Addict Join Date: Jul 2006 Location: barstow Posts: 1,303	mine came a week or so back and they are very nice just waitin on axle c's to install them all together

12-21-2006, 04:13 PM	#107
calyakker Pebble Pounder Join Date: Dec 2006 Location: Peoria, AZ Posts: 162	Got the bearings and knuckles today. Very nice finish on these knuckles. I'm impressed. Thanks

12-21-2006, 06:23 PM	#108
Trikster RCC Addict Join Date: May 2006 Location: Roseville Posts: 1,469	Mine finally came in, thanks for the parts! They look really nice. I was looking the knuckles over and it looks like the ones I have are side specific, one post is higher than the other one. Is this what the washers are for?

12-21-2006, 11:19 PM	#110
Trikster RCC Addict Join Date: May 2006 Location: Roseville Posts: 1,469	They look fantastic though, cannot wait to polish them up to match my Bruiser frame I have about 15 hours into polishing. I can shave looking into the frame...

12-22-2006, 12:04 AM	#111
Cloak I wanna be Dave Join Date: Jan 2006 Location: Albuquerque Posts: 2,206	I might have just hit a quality control issue on mine, but I've had to rethread 2 of the 6 I've opened so far (of . Not a big deal at all, but just thought you might want to know. The holes are cut exactly where they should be, but the threads themselves were pretty rough and wouldn't let me start the screw. Once I cleaned it up, it threaded perfectly and they turn smooth as butter. I think you've got me convinced that I need them on my other trucks now.

12-23-2006, 06:01 AM	#112
run2jeepn I wanna be Dave Join Date: Sep 2005 Location: USA Posts: 11,196	I;m running low again on Knuckles and bearing so if you need any soon. Need to place your orders while I still have them. Once again not sure when the next batch will be in.

Sponsored Links

12-26-2006, 08:18 PM	#113
run2jeepn I wanna be Dave Join Date: Sep 2005 Location: USA Posts: 11,196	Just sold a few more. I have about a dozen left.

12-27-2006, 01:18 PM	#114
run2jeepn I wanna be Dave Join Date: Sep 2005 Location: USA Posts: 11,196	I only have 3 sets left....These need to go as always....I'm trying to place another order for more as we speak....Just haven't heard back from them yet. So if you need a set order now....I will take pre-orders for the next batch if you wouldn't mind wating around a week to get them.

12-27-2006, 01:32 PM	#115
Rat1 Quarry Creeper Join Date: Nov 2006 Location: Rats nest Grafton ND Posts: 381	Well i am going to need a set of knuckles and Cs for my TLT real soon. Hope you still have a enough next week or so.

12-27-2006, 02:09 PM	#117
MuddKnuckle Newbie Join Date: Dec 2006 Location: Corpus Christi Posts: 20	Payment sent for knuckles Thanks

12-27-2006, 02:37 PM	#119
hlpressley Quarry Creeper Join Date: Aug 2006 Location: Monroe NC Posts: 456	You better get em' while you can guys. You can't beat his service or price! He is a great guy on top of that.

12-27-2006, 02:56 PM	#120
clodstall I lost my vendor privileges Join Date: May 2006 Location: TOP OF THE HILL Posts: 3,014	waiting on money at the moment. if i get it in time i will order these also.

RCCrawler Forums

Thread: TLT Bearings and Knuckles