Go Back   RCCrawler Forums > Vendors > Vendors Market > Chassis and Suspension
Loading

Notices

Thread: Fungi's Specter (micro Wraith kit)

Reply
 
LinkBack Thread Tools Display Modes
Old 09-02-2015, 08:16 AM   #1
RCC Addict
 
Join Date: Jan 2011
Location: Forest Floor
Posts: 1,108
Default Fungi's Specter (micro Wraith kit)

Specter Micro Chassis Kit by Fungi



Specter Kit.


Optional Interior Kit.

Last edited by Fungi; 09-08-2015 at 06:20 PM.
Fungi is offline   Reply With Quote
Sponsored Links
Old 09-02-2015, 08:17 AM   #2
RCC Addict
 
Join Date: Jan 2011
Location: Forest Floor
Posts: 1,108
Default Re: Fungi's Specter (micro Wraith kit)

Assembly Guide

First step before anything is to clear the excess powder from the small holes. It's not as much a problem when it's open on both ends, but these definitely need to be cleaned out. Trying to screw into these when they are full of powder can ruin the chassis!


Install the two laser cut Delrin sub chassis parts using the supplied 0-80 x 1/4" screws (10). It can help to screw the screws into and back out of the sub chassis parts before attaching them to the chassis.


Install the transmission as shown, or you can flip it so the motor is pointing forward but you will need to swap the motor wires if you do that. Be careful not to over tighten the screws.



Install the ball studs into the sub chassis as shown. It is not necessary to use a lock nut, but it doesn't matter if you want to.


Carefully bend the plastic around a round object like a screw driver shaft. Easy does it. You want a nice gradual bend, not a crease. Align it to the chassis to see where to bend.



Should look something like this.


A little olive drab.


Install the body panel using the provided 0-80 x 1/8" screws (14).


Carefully cut out the hood and roof panels then drill the holes. Us a .06" (1/16") drill bit. Install them using the included 0-80 x 1/8" screws (9). After you have them fit properly you can paint them.


For a 5" wb, make the upper links, 1.7" long and the lower links 2.15" long. For a 5.3" wb make the upper links 1.8" long and the lower links 2.3" long. Measure the entire length, not on center. It's important that they are as close as possible to the same length.


Attach the long links to the transmission and the short links to the sub chassis.


I do a semi droop on the suspension. I use Losi Micro-T rear springs, white in front and red in the rear. Also remove the plastic "stop" on the shock to give it full movement. Alternately you can use stock springs if you cut off about 3 wraps.


Attach the axles as shown. Make sure the drive shafts go together properly. They are keyed, if they are off by 90 degrees they will not move freely and bind.


Connect the shocks as shown. Alternately you can mount them to the sub chassis.


Put the wheels on and viola, it's a roller.


I put the ESC in heat shrink and double sided taped it to the back deck.


I put a small 180mAh lipo behind the dash. I never take it out. I just leave it inside even to charge.


If you're doing an interior you will need to install the offset skid. First remove the factory skid, and save the screws. You will need a very small head on the Phillips driver. If it doesn't fit well you can strip the head. Remove the four ball studs.


Remove the three screws that hold the transission gear cover. It will not be put back on.


Install the four ball studs in the new offset skid as shown. Make sure they drive in straight and don't over tighten.


Attach the skid to the transmission. Carefully snip the rounded top and the left screw holes off the metal plate. You can use a file after nipping to smooth it. See the next picture for more clarification.




Cut out the interior tub to look like this.


Here it is with the interior vacuum formed part.


This shows the interior part painted and glued to the frame.


This is how I positioned the driver figure.


Here is where I got the seats.


Here's where I got the driver.


Remove the parts from the panel and clean them with alcohol if necessary. The shifters are straight pins (not included) with the tops painted black. I turned the boot parts over and glued them together.


The screw will self tap into the tube to hold the steering wheel, and the tube will friction fit into the dash. Then glue the dash into the frame.

Last edited by Fungi; 09-17-2015 at 06:25 PM.
Fungi is offline   Reply With Quote
Old 09-02-2015, 08:23 AM   #3
Rock Crawler
 
Join Date: Jan 2014
Location: Frog Lake AB, Canada
Posts: 696
Default Re: Fungi's Specter (micro Wraith kit)

Dammit, I seen this on shapeways a couple days ago, I should've added it to my cart. Am I mistaken or did I also see a fastback version of this cage chassis too.
Alexander_0_1 is offline   Reply With Quote
Old 09-02-2015, 08:25 AM   #4
I wanna be Dave
 
Join Date: Aug 2006
Location: under a rock and a hard place
Posts: 5,443
Default Re: Fungi's Specter (micro Wraith kit)

That is super cool. Will you be adding a package deal that includes all necessary parts ?

Meaning: links, interior/seats/steering wheel, body/chassis set ? any other items I missed....(driver)
hotwheels000 is offline   Reply With Quote
Old 09-02-2015, 08:54 AM   #5
RCC Addict
 
Join Date: Jan 2011
Location: Forest Floor
Posts: 1,108
Default Re: Fungi's Specter (micro Wraith kit)

You guys are fast. lol Alexander - I do have a fastback and a truck version. Hotwheels - I do have them in full kits. I am still putting the interior kits together, but they will not include driver, seats, or steering wheel. These parts can be found in model kits. I will provide links where I purchased the seats and driver character though.

Check out the catalog.
https://drive.google.com/file/d/0B6h...XN5cmltLWU3MVk
https://drive.google.com/file/d/0B6h...1BRQUU2V1piT00
https://drive.google.com/file/d/0B6h...1VaaVlheUE3aVU
Fungi is offline   Reply With Quote
Old 09-02-2015, 08:59 AM   #6
Rock Crawler
 
Join Date: May 2008
Location: carson city
Posts: 518
Default Re: Fungi's Specter (micro Wraith kit)

That is a amazing how to post. Glad to see this chassis made.
Now to get another losi micro crawler. The last one i had is a quad now.
Werty Made is offline   Reply With Quote
Old 09-02-2015, 09:03 AM   #7
I wanna be Dave
 
Join Date: Oct 2007
Location: Castle Rock, WA
Posts: 8,786
Default Re: Fungi's Specter (micro Wraith kit)

Very cool chassis setup for a micro!!!!!!!!!
Szczerba is offline   Reply With Quote
Old 09-02-2015, 09:04 AM   #8
Rock Crawler
 
Join Date: Jan 2014
Location: Frog Lake AB, Canada
Posts: 696
Default Re: Fungi's Specter (micro Wraith kit)

I'm in for a full kit! I wasn't a big fan of the fungi micro R1, but this beats that hands down. Too bad my wraith doesn't have solid axles anymore, or I'd've made a micro version.

I was going to order the sad keanu off of shapeways...you know, to glue to the dashboard of my sister Ford fusion, I wonder if he'll/it'll fit in this thing.


I'm addicted to shapeways, and all I went there for was that GCM bigblock, now I'm hooked.

Last edited by Alexander_0_1; 09-02-2015 at 09:08 AM.
Alexander_0_1 is offline   Reply With Quote
Old 09-02-2015, 09:35 AM   #9
RCC Addict
 
Join Date: Mar 2012
Location: Under a Rock in North Texas
Posts: 1,389
Default Re: Fungi's Specter (micro Wraith kit)

Great work, Jim! I may have to order up one of these for my sons birthday. Not that he's not already spoiled enough, as my wife and I bought him an iPad Mini, but still....I think he needs this for his micro. That thing hasn't been switched on in at least a year. Time to get it goin' again!
Sh0rtBus is offline   Reply With Quote
Old 09-02-2015, 10:34 AM   #10
I wanna be Dave
 
Join Date: Aug 2006
Location: under a rock and a hard place
Posts: 5,443
Default Re: Fungi's Specter (micro Wraith kit)

Quote:
Originally Posted by Fungi View Post
You guys are fast. lol Alexander - I do have a fastback and a truck version. Hotwheels - I do have them in full kits. I am still putting the interior kits together, but they will not include driver, seats, or steering wheel. These parts can be found in model kits. I will provide links where I purchased the seats and driver character though.

Check out the catalog.
https://drive.google.com/file/d/0B6h...XN5cmltLWU3MVk
https://drive.google.com/file/d/0B6h...1BRQUU2V1piT00
https://drive.google.com/file/d/0B6h...1VaaVlheUE3aVU
Prrfect, I want order the whole package when the interior is available. Please update this thread, such a cool little conversion
hotwheels000 is offline   Reply With Quote
Old 09-03-2015, 03:59 PM   #11
I wanna be Dave
 
Join Date: Aug 2006
Location: under a rock and a hard place
Posts: 5,443
Default Re: Fungi's Specter (micro Wraith kit)

PM sent
hotwheels000 is offline   Reply With Quote
Old 09-04-2015, 01:17 PM   #12
Rock Crawler
 
Join Date: Dec 2013
Location: Nevada City
Posts: 872
Default Re: Fungi's Specter (micro Wraith kit)

I just got mine in the mail from shapeways! Unfortunately, one of the body mounts didn't print, so I've already contacted shapeways and I'm confident they'll make good. Aside from that, my first thought: WOW! Definitely worth all the time and effort. I will definitely be ordering more in the future. Thank you Jim for taking things to the next level and making these awesome chassis' for us all.
Attached Images
 
R.Billy Rob is offline   Reply With Quote
Old 09-07-2015, 07:09 AM   #13
RCC Addict
 
Join Date: Jan 2011
Location: Forest Floor
Posts: 1,108
Default Re: Fungi's Specter (micro Wraith kit)

Dammit, I've had dozens of chassis made already and nothing like that has happened. :( Please let me know what they say!
Fungi is offline   Reply With Quote
Old 09-07-2015, 08:21 PM   #14
Rock Crawler
 
Join Date: Dec 2013
Location: Nevada City
Posts: 872
Default Re: Fungi's Specter (micro Wraith kit)

No worries, I'm in contact, and they say they just have to figure out what happened in production, and then they have a request for reprint. So I'm thinking I might have just gotten an extra chassis out of it. If so, I think I already have a good use for it! in the meantime I've already set it up, just without the one body mount.
R.Billy Rob is offline   Reply With Quote
Old 09-08-2015, 12:02 PM   #15
RCC Addict
 
Join Date: Apr 2011
Location: San Diego
Posts: 1,630
Default Re: Fungi's Specter (micro Wraith kit)

Man I may have to pick one of these up instead of trying to do the leaf sprung chassis for my micro. great work! Looks fantastic.
Shinjari is offline   Reply With Quote
Old 09-08-2015, 02:03 PM   #16
RCC Addict
 
Join Date: Aug 2013
Location: Missoula
Posts: 1,346
Default Re: Fungi's Specter (micro Wraith kit)

PM sent as well.
maslin is offline   Reply With Quote
Old 09-08-2015, 06:13 PM   #17
Rock Crawler
 
Join Date: Jun 2012
Location: jville
Posts: 580
Default Re: Fungi's Specter (micro Wraith kit)

Pretty darn awesome
gsrcivic is offline   Reply With Quote
Old 09-08-2015, 09:19 PM   #18
I wanna be Dave
 
Join Date: Aug 2006
Location: under a rock and a hard place
Posts: 5,443
Default Re: Fungi's Specter (micro Wraith kit)

I see you have edited the posts to add the interior.... is it now available ?
hotwheels000 is offline   Reply With Quote
Old 09-09-2015, 10:54 AM   #19
RCC Addict
 
Join Date: Jan 2011
Location: Forest Floor
Posts: 1,108
Default Re: Fungi's Specter (micro Wraith kit)

Yes, I am taking pre-paid orders and shipping in 7 to 10 days.
Fungi is offline   Reply With Quote
Old 09-15-2015, 12:46 AM   #20
I wanna be Dave
 
Join Date: Aug 2006
Location: under a rock and a hard place
Posts: 5,443
Default Re: Fungi's Specter (micro Wraith kit)

What stand offs/pivot balls are those in the shock picture ?
hotwheels000 is offline   Reply With Quote
Reply



Fungi's Specter (micro Wraith kit) - Similar Threads
Thread Thread Starter Forum Replies Last Post
Fungi's Micro Ladder Frame Kit Fungi Chassis and Suspension 10 02-15-2020 10:33 AM
Fungi's Micro Goat Chassis Kit Fungi Chassis and Suspension 4 06-10-2015 08:01 PM
Fungi's Micro Elcipse Chassis Kit Fungi Chassis and Suspension 1 02-23-2015 08:05 AM
Fungi's Micro Axle Bracket Kit Fungi Chassis and Suspension 0 02-10-2015 08:34 PM
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -6. The time now is 06:24 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com