Go Back   RCCrawler Forums > Miscellaneous > Chit Chat
Loading

Notices

Thread: SSD Third Member for Baja/Rock Rey Review

Reply
 
LinkBack Thread Tools Display Modes
Old 04-15-2017, 12:57 PM   #1
RCC Addict
 
Join Date: May 2009
Location: Weston
Posts: 1,319
Default SSD Third Member for Baja/Rock Rey Review

First I'll start with how I got one. I was doing my usual posting around the board and got a message from SSD asking if I would like to try one of their third members? Only catch was I had to do a review.

So here it is. My review on the SSD third member.

First the packaging,

Everything was individually wrapped to keep it from scratching. A+ for packaging



Then there is bearing size. Much larger on both sides. Very nice as the stockers are way too small. These should hold up well to all kinds of running. A for bearing size.



Up next, the install. His took a whole 5 minutes. The only issues was breaking the overload of loctite on the drive shaft to slide it off. After it was installed I seem to have a tighter mesh. Not sure if this was planned but it's definitely not too tight. It feels as it would if I went it to shim it only I didn't use any shims. A+ for ease of install.










So that's it for the install. One of the easiest things I have ever done. I have only run one pack through it so far but it feels great and I haven't had any issues. I will be back to update after a few more runs but so far so good.
Rjohn929 is offline   Reply With Quote
Sponsored Links
Old 04-15-2017, 02:19 PM   #2
I wanna be Dave
 
Join Date: Jun 2016
Location: Deep in the Everglades
Posts: 5,781
Default Re: SSD Third Member for Baja/Rock Rey Review

I have to agree about install.... mine was the smoothest install on my yeti. Wish I had done the wide, but I won't complain, great product!


Hang up and Drive
mikemcE is offline   Reply With Quote
Old 04-15-2017, 02:20 PM   #3
I wanna be Dave
 
Join Date: Apr 2015
Location: Roseville, Ca
Posts: 2,506
Default Re: SSD Third Member for Baja/Rock Rey Review

I can also add my SSD install was super easy. Inner bearing was a little tight but got it in no problem. Getting the stock driveshaft grub screw out on the other hand was a pain. Had to use a mini torch to break the seal, since the whole grub screw has loctite on it. I did add one 0.1mm shim on the pinion ontop of the 0.1mm shim that came factory and mesh is perfect now.

Good job SSD!
84yoda is offline   Reply With Quote
Old 04-15-2017, 03:06 PM   #4
Rock Stacker
 
Join Date: Jan 2017
Location: Maui
Posts: 49
Default Re: SSD Third Member for Baja/Rock Rey Review

Love my SSD third. Put about 7 pack through it. Now I can stop worrying about my bearing on 3s.

Sent from my SM-G920V using Tapatalk
not-required is offline   Reply With Quote
Reply



SSD Third Member for Baja/Rock Rey Review - Similar Threads
Thread Thread Starter Forum Replies Last Post
Losi Baja Rey and Rock Rey Aluminum Hop-ups - In Stock! RPP Hobby RPP Hobby 4 03-22-2017 04:30 PM
Added section for Baja/Rock Rey Wes S. Comments, Suggestions, and Help 2 01-04-2017 09:28 AM
Losi baja rey snowman13 Vaterra Twin Hammers 3 05-12-2016 07:01 PM
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -6. The time now is 01:13 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2022, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com