Quote:
However 3-6s would be a nice touch and pretty much corner esc's for a while... |
Quote:
|
Quote:
|
What is the ETA? I see Amainhobbies posted it up on their site. You get a response on on the "400" sized lower turn motors on 2 cell? I might go 3 cell and some 35t 540 sized. Just have to see what shakes out with the specs. Cause I don't want to blow one up on 3s if the spec says 2cell and then not get it warrantied. |
Quote:
If we change the M2 spec to 3S, it will be "official" and the M2s would be covered by our warranty. We will be shipping the controller/system in November. |
Quote:
|
except a decent drag brake and not just hold. |
Quote:
Quote:
http://www.teamnovak.com/products/m2_combo/index.html |
i assume thats really hold brake not drag brake, just like a my goat has 10 settings for drag brake but has none only hold. maybe i'm wrong, maybe they figured out we drive these things downhill to. |
Quote:
If these will do 3s, I might have to try one on my next rebuild. "thumbsup" |
Got me interested for sure.. On a side note..I started a Novak social group..Come join up guys if you run novak products..Here's the link.. http://www.rccrawler.com/forum/group.php |
Why only 55T motors in the combo kit? Or will there be other motors later on? Having this, the rx, and a battery on the skid is just awesome... |
Quote:
|
Quote:
We are testing the M2 on 3S packs. I will post updates here as available. |
Cool thanks "thumbsup" I may just buy it separate and then just pick up some new 35T motors... |
Howdy Folks, I had a chance to operate the M2Dig for 4 whole days while I was working the Novak Booth ath the I Hobby Expo last week. While I didn't have a chance to get out on the rocks with it, here's how it works, and works well in my opinion. You can use it just like an ESC/Dig Switch combo. So you have Front Rear Dig from a 3pos switch. OR, you can use it to have F/R Dig, PLUS motor Biasing. You setup your radio with one 3Pos Switch to do the dig, and ONE switch as a Linear Trim Pot on the Aux Channel. So you can Dial in more Clod Stall (IE Free Wheel), or Dial out Clod Stall completely while you drive. Basically, as you're driving you can tap the Linear Adjust switch to reduce power to F/R motor. If you loose count of how many "clicks" you put in, Simply DIg that same side On/Off and everything is back to normal again. It really is super easy to use. Novak Two- I'm patiently waiting my very own M2Dig...... |
I like the sound of that, only thing holding me back right now it the 3S thing, other than that I am in... Did I miss it? Is there an internal BEC or external? |
Novak just cannot see that most like 3S or some even 4S. This system sounds interesting and I would be interested in trying it out but not if I have to back down to 2S. I'll stick with Castle. |
After reading all the specs. and seeing the video of it working at the hobbie show am really impressed with this new Novak Product, Being a Novak fan for over 5 years all my cars run on Novak. My only question is after looking at the specs I have the same question as pretty much everyone on here is this going to be a 2S or 3S system? I see no sence in only making it it 2S when you guys have already brought out a 2S-3S ESC. Here are specs for anyone that has not seen them and a Video of the system working on a Rig Enjoy. M2 DIG ESC/DUAL TERRA CLAW BRUSH COMBO FEATURES http://www.teamnovak.com/global_pics/x_bullet.jpgFully programmable, user-friendly interface with five adjustable parameters: Drag Brake (10 settings), Dead Band (5 settings), Minimum Drive (10 settings), Drive Frequency (10 settings) and Battery Type Selection (3 settings – Li-Po, Li-Fe and Ni-MH) http://www.teamnovak.com/global_pics/x_bullet.jpgIndependently powers the front or rear motors in a dual-motor crawler vehiclehttp://www.teamnovak.com/global_pics/x_bullet.jpgApplicable for dual-brushed motor or single-brushed motor applicationshttp://www.teamnovak.com/global_pics/x_bullet.jpgBuilt-in PC connection with new Novalink for expanded programminghttp://www.teamnovak.com/global_pics/x_bullet.jpgInternal high-voltage five-amps switching regulator to provide six volts of output without overheating the speed controlhttp://www.teamnovak.com/global_pics/x_bullet.jpgUniversal JST Input Plug for Ch.2 and Ch. 3, which fits all popular brand receivershttp://www.teamnovak.com/global_pics/x_bullet.jpgWater-resistant case with gasket seal http://www.teamnovak.com/global_pics/x_bullet.jpgThermal Overload Protectionhttp://www.teamnovak.com/global_pics/x_bullet.jpgMeets RoHS compliance and includes 120-Day Warrantyhttp://www.teamnovak.com/global_pics/x_bullet.jpgDesigned and assembled by Novak in Irvine, Calif., using globally-sourced components M2 DIG ESC/DUAL TERRA CLAW BRUSH COMBO SPECShttp://www.teamnovak.com/global_pics/x_bullet.jpgInput Voltage: 2S Li-Po/Li-Fe cells or 4-7 Ni-MH cells (1.2V/cell)http://www.teamnovak.com/global_pics/x_bullet.jpgESC Footprint: 1.16” x 1.47” (29.5 x 37.3 mm)http://www.teamnovak.com/global_pics/x_bullet.jpgESC Weight (w/o wires): 1.30 oz. (36.9g) http://www.teamnovak.com/global_pics/x_bullet.jpgMotor Limit: 27-turn 540-sized dual brushed motorshttp://www.teamnovak.com/global_pics/x_bullet.jpgBEC: 6.0 volts DC / 5.0 amps http://www.teamnovak.com/global_pics/x_bullet.jpgStatus LEDs: 4 on-board; 2 external http://www.teamnovak.com/global_pics/x_bullet.jpgVoltage Cut-Off: 6.25V (Li-Po), 4.75V (Li-Fe) (when Li-Poly Cut-Off Circuitry is enabled) http://www.teamnovak.com/global_pics/x_bullet.jpgPower Wires: 14G Super-Flex Copper-Strand Silicone Wire Here is the Video Link: http://www.youtube.com/watch?v=BkXu5kVoTUI |
3s for me here also. If you wanna sell it give us what we want"thumbsup" |
All times are GMT -6. The time now is 07:55 PM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com