GT3B Hack Question and Answer Thread

[kincer]

Got my hack kit yesterday and followed directions to a T and everything worked great! Thanks again losikid!

[losikid]

Originally Posted by jakester79

Look whos been at it again. This thing looks sweet! Any chance of firmware upgrades on this kit losikid?


flysky fs-t6 2.4ghz digital proportional 6 channel transmitter and receiver system

Thats been out for awhile...i don't offer stuff for the stick radios...i might in the future


I know there is a huge market as far as mods for the 9x, i haven't looked into the t6 yet

[MiniMorris]

Programming Question: I'm running a snow plow and i want my CH3 Trim switch to act as a 2 pos. switch so foward click goes to 100 and back click goes to -100 and will be non-mom. ?

[losikid]

Originally Posted by MiniMorris

Programming Question: I'm running a snow plow and i want my CH3 Trim switch to act as a 2 pos. switch so foward click goes to 100 and back click goes to -100 and will be non-mom. ?

Set your step to 200

[MiniMorris]

Originally Posted by losikid

Set your step to 200

Ok, Nice, I got it, the 200 got my positions correct, but i was seemed the switch wasn't linked to CH3. Turns out, for some reason I had the dual esc setting on and had to turn it to OFF, it was thinking CH3 was the REAR ESC. Now Work Great!

[jakester79]

Originally Posted by losikid

Thats been out for awhile...i don't offer stuff for the stick radios...i might in the future


I know there is a huge market as far as mods for the 9x, i haven't looked into the t6 yet

Thats strange I dont know why that didnt show up as a hyper link?
Further More thats not even the radio I was talking about...

Here lets try this.


2.4GHz枪型遥控系统 > 2.4GHz枪型遥控系统_FLYSKY RC Model Technology co., ltd.

[losikid]

Flysky FS-iT4

[72chevyrs10]

If i buy a gt3b how hard will it be to make it have all the same functions as a factory redcat rs10 radio? Looking to go 2.4 as we have quite a few of these trucks and i dont like changing crystals.

[losikid]

Originally Posted by 72chevyrs10

If i buy a gt3b how hard will it be to make it have all the same functions as a factory redcat rs10 radio? Looking to go 2.4 as we have quite a few of these trucks and i dont like changing crystals.

what are the functions?

[kincer]

Losikid I've got a problem, I hacked my other gt3b and everything went great, everything went perfect even my solder joints looked professional. Tested the radio and was working great, I'm running rechargeable AA's in it and they were getting low so I hooked it up to the wall charger to charge them in the radio and now it won't come on anymore. You told me I could still charge it like that, it didn't change the charging circuit. What can I do?

[losikid]

Have you tried different batteries?...

I promise you, changing the firmware and charging the batteries are not related at all

[kincer]

Yep I put new batteries in just to see, won't do a thing.

[losikid]

I suggest tearing it apart, and track the voltage....Check and make sure you have it at the battery tray, move up to the board, make sure you have at the connector, then check the vr, make sure you have voltage going in and back out of it...

[kincer]

Ok I have power going up to the board and power going in and out of VR, next lol?

[losikid]

You can try re flashing it...i doubt thats the issue...unless static electricity came off your charger and zapped the micro controller

[kincer]

I think its hosed, I guess I'll keep it for parts and order and hack a new one and just run a lipo like the other one, This sucks!

[kincer]

Just ordered gt3c from Hobbypartz will be on your site in a bit to order what I need to hack it.

[losikid]

Originally Posted by kincer

Just ordered gt3c from Hobbypartz will be on your site in a bit to order what I need to hack it.

They must of just got stock in....hmmm

I see no reason why charging it in the radio caused your other to quit working...i'd be interested at looking into it if your willing to send it to me?

[kincer]

Originally Posted by losikid

They must of just got stock in....hmmm

I see no reason why charging it in the radio caused your other to quit working...i'd be interested at looking into it if your willing to send it to me?

Sure I'll send it to you I'll have to wait til after the holidays though, I'm curious myself to what happened, I was so proud of my solder job it went way easier than the first one I wish I wouldn't have plugged it in, oh well at least it wasnt a $400 radio.

[losikid]

Originally Posted by kincer

Sure I'll send it to you I'll have to wait til after the holidays though, I'm curious myself to what happened, I was so proud of my solder job it went way easier than the first one I wish I wouldn't have plugged it in, oh well at least it wasnt a $400 radio.

Other folks have used the charge port just fine...whether if it was hacked or not, it was going to take a shit when it did...

Why does it need to wait? I'm not sure how much free time i'll have once 2013 comes, so sooner the better...but send me a pm when you want to send it in, so i can get you a shipping addy (It'll change here soon)