RCCrawler Forums

losikid · 12-31-2011, 01:38 AM

Quote:

Originally Posted by skinner

I found this link and was hoping alright to post it. Near bottom shows a way lipo mod can be done.
FlySky FS-GT3B 2.4Ghz 3CH Transmitter Radio RC FHSS | Ken buys... Reviews

Yea, its simple to add lipo, take out the tray and install a deans or whatever plug in its place.

Looking through his site this is interesting

PS3 HKS Racing Controller | Ken buys... Reviews

I wonder how neat it be for rc cars

skinner · 12-31-2011, 03:24 PM

Yea I seen that...just didn't wanna high jack thread.. but that controller was something else!!

losikid · 12-31-2011, 03:41 PM

Quote:

Originally Posted by skinner

Yea I seen that...just didn't wanna high jack thread.. but that controller was something else!!

Yea, i think thats gonna be my next personal project

Probably add a blue tooth model to the gt3b and put one in that controller so i can use on or the other and have no physical connection. So leave the gt3b turned on layign near by and just carry that controller

Use the steering thing for steering, the X and [ ] paddles for fwd/reverse, i'll probably use r1/r2 for full dig then use r2/l2 for propo dig. R2 increases L2 decrease and have the dig % displayed there in the center.

losikid · 12-31-2011, 04:18 PM

I'm getting close with this new manual, its taking for ever to write, hopefully it's helpful

skinner · 12-31-2011, 04:25 PM

Looking good man!

heyok · 12-31-2011, 04:28 PM

That manual looks like it will be a big help. Looking forward to it!

losikid · 12-31-2011, 05:03 PM

I'm hoping to have the programming stuff done by tonight, and posted up for review and comments. I'll still have stuff like table of contents, bind procedures, ch mapping templates, etc.

benoj · 12-31-2011, 07:31 PM

On my hacked gt3b when the steering epas are set to around 135+ when I steer to the direction that has that ep my rear esc goes full throttle but anything lower its fine and I do have the latest fw to my knowledge

losikid · 12-31-2011, 07:52 PM

Quote:

Originally Posted by benoj

On my hacked gt3b when the steering epas are set to around 135+ when I steer to the direction that has that ep my rear esc goes full throttle but anything lower its fine and I do have the latest fw to my knowledge

Yes, this is because the channel starts to overlap into the 2nd channel.

Its not a firmware issue, its a hardware issue. Which can't be fixed cheaply (it be alot cheaper just to get a adapter from servocity)

squatch71 · 12-31-2011, 08:27 PM

Skinner...cool thread....lots of stuff on that website

LosiKid...very good looking manual....looking forward to it.

losikid · 12-31-2011, 08:55 PM

This all i'm going todo tonight, lmk what ya'lls thoughts are. There's stil stuff missing, but for the most part all the programming stuff is there

https://docs.google.com/viewer?a=v&p...yOTc1&hl=en_US

losikid · 12-31-2011, 08:57 PM

One thing i don't like, and this is just on google docs for some reason, everything seems to be in bold.

losikid · 12-31-2011, 09:06 PM

This one is better if you have ms office 2007 or new

http://www.overkillrc.com/GT3B/manua...ed%20copy.docx

Chevdog · 12-31-2011, 09:42 PM

Hey losikid, I'm in the middle of programming my gt3b. This may sound like a stimulus question, but which firmware do I use? To me, all the choices are written in a different language, lol. There's a lot to choose from and none of them look like v 4.0, v 4.2 ect, thanks man.

losikid · 12-31-2011, 09:45 PM

0.4.1. Download the file you got in the email from me, and then open that into STVP

actual file name is something like gt3b-ch6-0.4.1.s19 if i remember right

Chevdog · 12-31-2011, 09:55 PM

I found the email that you sent me, it wont let me download them, It is asking for a username and password. Sorry man, I'm being a pain, Im just trying to get this thing going last minute.

losikid · 12-31-2011, 10:43 PM

Quote:

Originally Posted by Chevdog

I found the email that you sent me, it wont let me download them, It is asking for a username and password. Sorry man, I'm being a pain, Im just trying to get this thing going last minute.

download this link, then open it with stvp

http://www.overkillrc.com/GT3B-Firmw...-ch6-0.4.1.s19

Chevdog · 01-01-2012, 12:59 AM

Ok, I've got the radio all done, but it seems as though my 2nd channel doesn't have any signal. If I switch the esc's from Channel 2 to 3 and vise versa, the 3rd channel is the only thing that is opperating on the reciever.

losikid · 01-01-2012, 01:02 AM

does steering work?

Are you running dual esc's?

Chevdog · 01-01-2012, 01:09 AM

I switched rx's out since I have another, and now my esc try's to calibrate but says that the signal is too weak. I am trying to hook into 2 fxr's with a cc bec set at 6 volts and a fluent 3 channel rx.

12-31-2011, 03:24 PM	#942
skinner Quarry Creeper Join Date: Nov 2006 Location: out in boonies!! Posts: 349	Re: GT3B Hack Question and Answer Thread Yea I seen that...just didn't wanna high jack thread.. but that controller was something else!!

12-31-2011, 04:18 PM	#944
losikid Got Worms? Join Date: Jun 2009 Location: Golden, CO Posts: 6,116	Re: GT3B Hack Question and Answer Thread I'm getting close with this new manual, its taking for ever to write, hopefully it's helpful

12-31-2011, 04:25 PM	#945
skinner Quarry Creeper Join Date: Nov 2006 Location: out in boonies!! Posts: 349	Re: GT3B Hack Question and Answer Thread Looking good man!

12-31-2011, 04:28 PM	#946
heyok I wanna be Dave Join Date: May 2007 Location: Vancouver, BC Posts: 2,379	Re: GT3B Hack Question and Answer Thread That manual looks like it will be a big help. Looking forward to it!

12-31-2011, 05:03 PM	#947
losikid Got Worms? Join Date: Jun 2009 Location: Golden, CO Posts: 6,116	Re: GT3B Hack Question and Answer Thread I'm hoping to have the programming stuff done by tonight, and posted up for review and comments. I'll still have stuff like table of contents, bind procedures, ch mapping templates, etc.

12-31-2011, 07:31 PM	#948
benoj I wanna be Dave Join Date: Dec 2008 Location: Madrid, IA Posts: 2,015	Re: GT3B Hack Question and Answer Thread On my hacked gt3b when the steering epas are set to around 135+ when I steer to the direction that has that ep my rear esc goes full throttle but anything lower its fine and I do have the latest fw to my knowledge

12-31-2011, 08:27 PM	#950
squatch71 I wanna be Dave Join Date: Sep 2008 Location: four o six Posts: 2,101	Re: GT3B Hack Question and Answer Thread Skinner...cool thread....lots of stuff on that website LosiKid...very good looking manual....looking forward to it.

12-31-2011, 08:55 PM	#951
losikid Got Worms? Join Date: Jun 2009 Location: Golden, CO Posts: 6,116	Re: GT3B Hack Question and Answer Thread This all i'm going todo tonight, lmk what ya'lls thoughts are. There's stil stuff missing, but for the most part all the programming stuff is there https://docs.google.com/viewer?a=v&p...yOTc1&hl=en_US

12-31-2011, 08:57 PM	#952
losikid Got Worms? Join Date: Jun 2009 Location: Golden, CO Posts: 6,116	Re: GT3B Hack Question and Answer Thread One thing i don't like, and this is just on google docs for some reason, everything seems to be in bold.

12-31-2011, 09:06 PM	#953
losikid Got Worms? Join Date: Jun 2009 Location: Golden, CO Posts: 6,116	Re: GT3B Hack Question and Answer Thread This one is better if you have ms office 2007 or new http://www.overkillrc.com/GT3B/manua...ed%20copy.docx

12-31-2011, 09:42 PM	#954
Chevdog Pebble Pounder Join Date: Jan 2011 Location: Mtz Posts: 196	Re: GT3B Hack Question and Answer Thread Hey losikid, I'm in the middle of programming my gt3b. This may sound like a stimulus question, but which firmware do I use? To me, all the choices are written in a different language, lol. There's a lot to choose from and none of them look like v 4.0, v 4.2 ect, thanks man.

12-31-2011, 09:45 PM	#955
losikid Got Worms? Join Date: Jun 2009 Location: Golden, CO Posts: 6,116	Re: GT3B Hack Question and Answer Thread 0.4.1. Download the file you got in the email from me, and then open that into STVP actual file name is something like gt3b-ch6-0.4.1.s19 if i remember right

12-31-2011, 09:55 PM	#956
Chevdog Pebble Pounder Join Date: Jan 2011 Location: Mtz Posts: 196	Re: GT3B Hack Question and Answer Thread I found the email that you sent me, it wont let me download them, It is asking for a username and password. Sorry man, I'm being a pain, Im just trying to get this thing going last minute.

01-01-2012, 12:59 AM	#958
Chevdog Pebble Pounder Join Date: Jan 2011 Location: Mtz Posts: 196	Re: GT3B Hack Question and Answer Thread Ok, I've got the radio all done, but it seems as though my 2nd channel doesn't have any signal. If I switch the esc's from Channel 2 to 3 and vise versa, the 3rd channel is the only thing that is opperating on the reciever.

01-01-2012, 01:02 AM	#959
losikid Got Worms? Join Date: Jun 2009 Location: Golden, CO Posts: 6,116	Re: GT3B Hack Question and Answer Thread does steering work? Are you running dual esc's?

Sponsored Links

LinkBacks (?) LinkBack to this Thread: http://www.rccrawler.com/forum/electronics/321742-gt3b-hack-question-answer-thread.html
Posted By	For	Type	Date
RoboSavvy Forum :: View topic - SAM-3 Servo teardown	This thread	Refback	03-05-2013 12:49 PM

01-01-2012, 01:09 AM	#960
Chevdog Pebble Pounder Join Date: Jan 2011 Location: Mtz Posts: 196	Re: GT3B Hack Question and Answer Thread I switched rx's out since I have another, and now my esc try's to calibrate but says that the signal is too weak. I am trying to hook into 2 fxr's with a cc bec set at 6 volts and a fluent 3 channel rx.

RCCrawler Forums

Thread: GT3B Hack Question and Answer Thread