08-05-2011, 09:52 AM | #401 |
Pebble Pounder Join Date: Aug 2009 Location: taiwan
Posts: 146
|
When I click and release the ch3 trim button, it shows d-100 and is front wheel dig, if I want to have rear wheel dig then I need to push forward the ch3 trim button(d 100) hold it and pull the trigger at the same time, once I release the ch3 trim button it'll automatically change back to d-100. Can I do it vice versa? What I mean is when I click and release the ch3 trim button, it'll shows d 100 and have rear wheel dig. Where can I find the proper way to operate dig? Thanx! Last edited by kc092755; 08-05-2011 at 10:39 AM. |
Sponsored Links | |
08-05-2011, 10:55 AM | #402 |
Rock Crawler Join Date: Oct 2007 Location: Grants Pass
Posts: 806
|
Well I figured out all my problems are in the motors. Both of them seem to be crapped out. I have It working great now. with a motor swap. Just had a hard time believing these both crapped out like that being so new? Thanks for all the help figuring it out. I have another question now that I have it working on 2 crawlers and my jet boat, how about a 2spd setup for the 3rd ch? I would like ch trim button to run it if possible. What would be the easiest way to set up a 2 pos switch |
08-05-2011, 01:12 PM | #403 | |
Got Worms? Join Date: Jun 2009 Location: Golden, CO
Posts: 6,116
| Quote:
| |
08-05-2011, 01:25 PM | #404 | |
Got Worms? Join Date: Jun 2009 Location: Golden, CO
Posts: 6,116
| Quote:
Ok well there's two ways of doing this...well actually What switch are you wanting to use, a single button, or a two button switch (ch3 trim and d/r are two buttons) As there's actually alot of ways 2 button -set it to ch3, NOL, 200% step....then adjust epa's as needed. -Use MPO, i haven't really tested this yet, and i have no AA's so i can't be much assistance right now, but i'll go buy some over the weekend 1 button -set it up to go -100/100 then set your epa's -use MPO | |
08-05-2011, 01:32 PM | #405 | |
Rock Crawler Join Date: Oct 2007 Location: Grants Pass
Posts: 806
| Quote:
| |
08-05-2011, 01:39 PM | #406 | |
Got Worms? Join Date: Jun 2009 Location: Golden, CO
Posts: 6,116
| Quote:
| |
08-05-2011, 05:50 PM | #407 |
Newbie Join Date: Mar 2011 Location: Port Orchard
Posts: 40
|
can you make the 3ch button in to a 3pos switch?
|
08-05-2011, 06:07 PM | #408 |
Got Worms? Join Date: Jun 2009 Location: Golden, CO
Posts: 6,116
| |
08-05-2011, 07:27 PM | #409 |
Rock Crawler Join Date: Jun 2011 Location: Las Vegas/671
Posts: 985
|
Sorry I didn't read all the pages. can the 3rd channel be used to shift? Thanks |
08-05-2011, 07:55 PM | #410 | |
Pebble Pounder Join Date: Aug 2009 Location: taiwan
Posts: 146
| Quote:
Press and hold ch3 trim forward(d 100) has rear wheel dig, press and hold ch3 trim backward(d -100) front wheel dig, if I release the switch it shows d -100 with front wheel dig most of the time. Thanx! | |
08-05-2011, 11:48 PM | #411 | |
Got Worms? Join Date: Jun 2009 Location: Golden, CO
Posts: 6,116
| Quote:
| |
08-06-2011, 10:12 AM | #412 | ||
Newbie Join Date: Aug 2011 Location: thailand
Posts: 4
|
losikid: this is my first posting in this forum. first thanks a lot for you losikid , so i can hacked my GT3B. all of your posts so useful. i am trying to read the manual 0.4.0. but my english not very good. i am from south east asia (thailand). i just want to ask, is it possible if i want to have 4WS, DIG, and one channel to control my winch? i am successfully set 4WS from this posting, thanks vette66_00 Quote:
Quote:
once again thanks for your post very useful. sorry if my english is very bad, hope you understand | ||
08-06-2011, 10:14 AM | #413 |
Pebble Pounder Join Date: Aug 2009 Location: taiwan
Posts: 146
| I follow your "Dual ESC Mixing Template: (0.3.2 and 0.4.0 fw's)" setting. "Press and hold ch3 trim switch forward and backward while pulling the trigger", is this the right way to operate instant dig? Forgot to turn off gt3b and it drained the batteries, could you tell me how to do the power led mod? Thanx! Last edited by kc092755; 08-06-2011 at 08:03 PM. |
08-06-2011, 10:11 PM | #414 |
Rock Stacker Join Date: Mar 2007 Location: Bethpage,TN
Posts: 94
|
I was hesitant to buy such a cheaply priced transmitter but after all the great reviews and the amazing things optimistic is doing with this rd, I will be buying one ASAP along with several rx. Thanks |
08-08-2011, 04:21 PM | #415 |
Rock Crawler Join Date: Oct 2007 Location: Grants Pass
Posts: 806
|
I figured out how to set up the 3 pos switch i think but still cant seem to get it right. I can only adjust epa for one side and cant seem to find how to trim the 3rd ch. Any advice
|
08-08-2011, 05:41 PM | #416 | |
Got Worms? Join Date: Jun 2009 Location: Golden, CO
Posts: 6,116
| Quote:
Trim for ch 3...you have to go into sub trim...which will be long enter on trim | |
08-08-2011, 05:41 PM | #417 |
Got Worms? Join Date: Jun 2009 Location: Golden, CO
Posts: 6,116
| It will do you good, its abit low on overall quality, but it offers all the features high end radios do.
|
08-08-2011, 05:44 PM | #418 | |
Got Worms? Join Date: Jun 2009 Location: Golden, CO
Posts: 6,116
| Quote:
Yea, enough people have asked i'll do diy...although why not just set the screen not to turn off, or turn on the inactivity alarm? | |
08-08-2011, 05:46 PM | #419 | |
Got Worms? Join Date: Jun 2009 Location: Golden, CO
Posts: 6,116
| Quote:
| |
08-08-2011, 05:46 PM | #420 |
Got Worms? Join Date: Jun 2009 Location: Golden, CO
Posts: 6,116
| |
LinkBacks (?)
LinkBack to this Thread: http://www.rccrawler.com/forum/electronics/321742-gt3b-hack-question-answer-thread.html | ||||
Posted By | For | Type | Date | |
RoboSavvy Forum :: View topic - SAM-3 Servo teardown | This thread | Refback | 03-05-2013 12:49 PM |
| |