11-15-2011, 01:44 AM | #761 |
Pebble Pounder Join Date: Jul 2011 Location: Oregon IL
Posts: 130
|
The actual chrome rocker that pushes the microswitches broke. There are two tabs one for each micro and the one for the front trim cracked. A little CA and it's as good as new. I did switch it to the D/R rev for good measure. I guess I need to stop digging so hard Kind of hard to get a good shot of it. |
Sponsored Links | |
11-15-2011, 07:40 AM | #762 |
Newbie Join Date: Nov 2011 Location: St. Peter
Posts: 3
|
Or should I just put my ESC on channel 3 since I really dont need trim for that and put my rear steer on channle 2 so I have trim settings to center the servo? or is there a way to save my left/center/right values on the 3 pos switch when im driving because like I said it will work for two cycles through and then just zero out? Thanks Newbie Dan
|
11-15-2011, 04:10 PM | #763 | |
Got Worms? Join Date: Jun 2009 Location: Golden, CO
Posts: 6,116
| Quote:
Make sure your step rate is 100. To get end points adjust your epa | |
11-15-2011, 07:58 PM | #764 | |
Pebble Pounder Join Date: Jul 2011 Location: Oregon IL
Posts: 130
| Quote:
All is well again and the glue fix seems to be holding up. Time will tell. | |
11-16-2011, 03:38 PM | #765 |
I wanna be Dave Join Date: May 2006 Location: HONDURAS...ROCK HEAVEN
Posts: 5,076
|
Everything in stock yet? Can't get to the products page to order? Edit: Got in there, but it seems you are out of regulators Last edited by cartronicshn; 11-16-2011 at 03:41 PM. |
11-16-2011, 03:41 PM | #766 |
Got Worms? Join Date: Jun 2009 Location: Golden, CO
Posts: 6,116
| |
11-16-2011, 04:49 PM | #767 |
I wanna be Dave Join Date: Feb 2007 Location: South FL
Posts: 3,349
|
FYI got an Email today HobbyPartz.com has 10% off radio gear till 11/18/2011 using code HPZTX10 RC Transmitters and Receivers should almost cover shipping making it a few $$ cheaper |
11-17-2011, 04:58 PM | #768 |
Rock Crawler Join Date: Jun 2011 Location: Las Vegas/671
Posts: 985
|
Hi Losikid, I'm having a problem calibrating my AE-2 esc to the Flysky GT3B. I do get lights and steering but esc still blinks green,red and beeps. I have a cc bec on 2s. It works fine with the stock axial radio and receiver. I've tried everything in the manuel but still no luck. I'm also using this radio on another rc, works good. Thanks |
11-17-2011, 05:02 PM | #769 |
Got Worms? Join Date: Jun 2009 Location: Golden, CO
Posts: 6,116
|
Try reversing the throttle channel
|
11-17-2011, 05:13 PM | #770 |
I wanna be Dave Join Date: Feb 2007 Location: South FL
Posts: 3,349
|
the bearings and VRs showed up today Ill crack both radios open and start the upgrades when my stomach isnt going crazy ughh |
11-17-2011, 06:59 PM | #771 |
Rock Crawler Join Date: Jun 2011 Location: Las Vegas/671
Posts: 985
| |
11-17-2011, 08:31 PM | #772 |
I wanna be Dave Join Date: Sep 2008 Location: four o six
Posts: 2,101
|
does your steering work???
|
11-17-2011, 09:15 PM | #773 |
Rock Crawler Join Date: Jun 2011 Location: Las Vegas/671
Posts: 985
| |
11-17-2011, 09:20 PM | #774 |
Got Worms? Join Date: Jun 2009 Location: Golden, CO
Posts: 6,116
|
Did you calibrate the esc to it? Right after you power up the rc, pull trigger (green lights should blink) once it beeps push trigger to full reverse (red lights should flash) once it beeps let off to center/neutral. It should be beep again then after a second or so it should do the startup jingle. |
11-17-2011, 09:21 PM | #775 |
I wanna be Dave Join Date: Feb 2007 Location: South FL
Posts: 3,349
|
Not to imply you don't know what you are doing but maybe you aren't calibrating it right? Axial AE-2 ESC Set-up and Programming |
11-17-2011, 10:40 PM | #776 | ||
Rock Crawler Join Date: Jun 2011 Location: Las Vegas/671
Posts: 985
| Quote:
Quote:
I guess I need a new receiver, good thing they are cheap. Thanks guy's for all the help. Hopefully no more problems when I get the new receiver. Last edited by Erbing; 11-17-2011 at 11:04 PM. | ||
11-18-2011, 04:37 AM | #777 |
I wanna be Dave Join Date: Nov 2010 Location: 07456 N. NJ USofA
Posts: 8,314
| At least you figured out what the issue is. |
11-19-2011, 06:40 PM | #778 |
I wanna be Dave Join Date: Feb 2007 Location: South FL
Posts: 3,349
|
flashed the 2nd GT3B tonight. I cant believe how much quicker and easier it is now that the virtual XP is sorted. also installed both VR's and set the low voltage alarm to 6.2 I have a pair of 2S 1300mahs that should work well. Once I pick up a 12mm reamer from the LHS I'll install the bearings. so to recap... 2 GT3B's about $65 firmware flasher, X2 VR's & bearing mods $63.25. total under $130 for 2 hacked and upgraded radios Making your spektrum & futaba friends jealous because you have 2 radios that can do more for 1/2 to a 1/4 what they paid....priceless |
11-19-2011, 06:45 PM | #779 | |
Got Worms? Join Date: Jun 2009 Location: Golden, CO
Posts: 6,116
| Quote:
| |
11-19-2011, 06:48 PM | #780 |
I wanna be Dave Join Date: Feb 2007 Location: South FL
Posts: 3,349
|
thanks for the heads up |
LinkBacks (?)
LinkBack to this Thread: http://www.rccrawler.com/forum/electronics/321742-gt3b-hack-question-answer-thread.html | ||||
Posted By | For | Type | Date | |
RoboSavvy Forum :: View topic - SAM-3 Servo teardown | This thread | Refback | 03-05-2013 12:49 PM |
| |