flysky gt3b

[EMUTT]

Can you use the third channel on a gt3b for a 3racing winch,without having to mod it?

[losikid]

You have to mod it

[EMUTT]

So can you just install some push buttons for the third channel or does it have to be hacked?

[erikblank]

It has to be hacked.

[EMUTT]

Ok so I just want 3 channels do I still need to get the $25 hack kit? Or is there a way to hack it without the kit just for the 3rd channel?

[heyok]

Originally Posted by EMUTT

Ok so I just want 3 channels do I still need to get the $25 hack kit? Or is there a way to hack it without the kit just for the 3rd channel?

The hack is a great one and I recommend it, but there is another way.

I make a winch controller that will work from a two position channel:
Winch Controller for Radio with 2 Position Third Channel

Watch the little youtube video to quickly see how it works.

[erikblank]

The radio comes with 3 channels and it already was the buttons and switches. The reason you need the hack kit is the stock rx doesn't have the programming you need to run the winch. You could make your own hack kit. You'd save about $5. Do yourself a favor buy it from losikid. His support is second to none.

[EMUTT]

Originally Posted by erikblank

The radio comes with 3 channels and it already was the buttons and switches. The reason you need the hack kit is the stock rx doesn't have the programming you need to run the winch. You could make your own hack kit. You'd save about $5. Do yourself a favor buy it from losikid. His support is second to none.

Ohh I thought the controller for the winch bypassed the receiver. My thoughts where that the controller has a push button on it,1press out,press again stop,press again in. So I was hopeing the third channel on the radio would work as the push button on the winch controller.

[erikblank]

It will with 4.1 firmware

[EMUTT]

Do I need a hack kit to upgrade firmware?

[erikblank]

Yes

[highlandcrawler]

Originally Posted by EMUTT

Ohh I thought the controller for the winch bypassed the receiver. My thoughts where that the controller has a push button on it,1press out,press again stop,press again in. So I was hopeing the third channel on the radio would work as the push button on the winch controller.

The problem with the stock radios 3rd ch is that its only a 2 pos switch for the 3rd ch. you would only have one direction of travel from it unless you used the heyok unit. You can however still just use the stock winch controller by just pushing the buttons

Originally Posted by EMUTT

Do I need a hack kit to upgrade firmware?

Yes. To upgrade the firmware on the radio you need a way to communicate with it. the Overkill hack kit will allow you to unlock all the possibility of the radio

[EMUTT]

Thanks a lot for the info guys looks like after I get the radio I will be pushing the button on the controller for a while lol. Eventually I will get the hack kit from losikid. Thanks again guys

[heyok]

Originally Posted by erikblank

The radio comes with 3 channels and it already was the buttons and switches. The reason you need the hack kit is the stock rx doesn't have the programming you need to run the winch. You could make your own hack kit. You'd save about $5. Do yourself a favor buy it from losikid. His support is second to none.

Just a little correction.

The stock rx doesn't limit you to a two position third channel. The transmitter in its stock form is responsible for that.

Yes, losikid makes a great kit!

Also, as I said, you could replace the winch controller with one of mine to make the winch operate on a radio with a two position channel. See my previous post (post 6 in this thread).

[EMUTT]

Yes sir I seen that and thanks for informing me on your wonderful products. Heard nothing but good things about your electronics. But the hack kit is the way I will eventually be going I'm sure I will eventually need more than 3 channels lol.