Go Back   RCCrawler Forums > RCCrawler General Tech > Electronics
Loading

Notices

Thread: hitech 7950

Reply
 
LinkBack Thread Tools Display Modes
Old 10-21-2011, 03:22 PM   #1
Quarry Creeper
 
Join Date: Oct 2011
Location: Waterford
Posts: 266
Default hitech 7950

Ok just got a used hired 7950 installed it turned everything on centered it and now it goes full lock left.but maybe 3/4 to the right can't change endpoints to fix it though any ideas?
foratm is offline   Reply With Quote
Sponsored Links
Old 10-21-2011, 03:48 PM   #2
RCC Addict
 
Join Date: Jun 2008
Location: Amish Buggy PA
Posts: 1,100
Default

Quote:
Originally Posted by foratm View Post
Ok just got a used hired 7950 installed it turned everything on centered it and now it goes full lock left.but maybe 3/4 to the right can't change endpoints to fix it though any ideas?
Hmm thats odd not sure why someone would program a servo like that when your radio does that for you. Servo programmer is exactly cheap for a one time use so that kinda sucks you are in this situation. You know anyone that has one? Did you double check your radio epas just to make sure?
DRCrawlGood is offline   Reply With Quote
Old 10-21-2011, 03:54 PM   #3
I wanna be Dave
 
Join Date: May 2007
Location: Vancouver, BC
Posts: 2,376
Default

Sounds to me like the circuitry inside the servo is broken. Plug another servo into the same slot of the receiver and see if it is working right for you. If it does, it likely means that the first servo is broken.

Probably a good doner to become a servo winch
heyok is offline   Reply With Quote
Old 10-21-2011, 04:56 PM   #4
Quarry Creeper
 
Join Date: Oct 2011
Location: Waterford
Posts: 266
Default

ok so i have been messing with the radio even set the end point to 150 percent into the danger zone and it turns a little bit more but just isnt really there yet. so programer will be my next try i'll find someone hopefully.
foratm is offline   Reply With Quote
Old 10-21-2011, 05:18 PM   #5
I wanna be Dave
 
Join Date: May 2007
Location: Vancouver, BC
Posts: 2,376
Default

Quote:
Originally Posted by foratm View Post
ok so i have been messing with the radio even set the end point to 150 percent into the danger zone and it turns a little bit more but just isnt really there yet. so programer will be my next try i'll find someone hopefully.
Sorry, misread your first post. Read it too quickly and skipped over the important stuff like what it was actually doing. Hope the programming fixes you up.
heyok is offline   Reply With Quote
Old 10-21-2011, 05:34 PM   #6
RCC Addict
 
Join Date: Jun 2008
Location: Amish Buggy PA
Posts: 1,100
Default

Quote:
Originally Posted by heyok View Post
Sounds to me like the circuitry inside the servo is broken. Plug another servo into the same slot of the receiver and see if it is working right for you. If it does, it likely means that the first servo is broken.

Probably a good doner to become a servo winch
Ya that would make a great winch but I think I would send it off to Hitec first and see what it will take to get it fixed. I have had great experience with Hitec so 99% of my servos are from them.
DRCrawlGood is offline   Reply With Quote
Old 10-21-2011, 05:59 PM   #7
Quarry Creeper
 
Join Date: Oct 2011
Location: Waterford
Posts: 266
Default

ok guys i figured it all out thanks a lot.
foratm is offline   Reply With Quote
Old 10-21-2011, 07:07 PM   #8
I wanna be Dave
 
Join Date: Nov 2010
Location: 07456 N. NJ USofA
Posts: 8,314
Default

Quote:
Originally Posted by foratm View Post
ok guys i figured it all out thanks a lot.
What did you figure out?? Someone else may have the same issue some day.

Hmmm....maybe you found the servo horn wasn't centered??

Nevermind......here...http://www.rccrawler.com/forum/elect...ch-thread.html post #685.
Charlie-III is offline   Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -6. The time now is 11:36 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com