RCCrawler Forums

jthellfire911 · 09-02-2012, 04:39 PM

Ok.. so searching on my phone is a big pita. Plus I haven't really found the info I'm looking for so hence my questions ..
I've got a 6lb ish scx10 with overdrive front gears, rr trans gears, mmp with ccbec, cs170 steering, 645/heyok winch, 1300mah 3s skylipos, spektrum rx/tx. Right now I'm running a novak rockstar 35t 20/86 gearing.
So with that out of the way I'm looking for a brushless motor that will give me close to the same low speed control and faster high speed than my setup has now."I know its impossible to have the best of both worlds." So my thoughts are either 13.5 novak crawler, 18.5 novak crawler, or run my brushed motor on 4s for the high speed I'm wanting and carry lots of extra brushes with me. Thoughts and opinions. Go!

jthellfire911 · 09-02-2012, 04:40 PM

I do run in water and some mud and can corrosionx the motor and waterproof the sensor areas. All other electronics on the rig are waterproofed already.

jthellfire911 · 09-03-2012, 05:30 PM

Really no one? No thoughts on just going 4s with the brushed motor? Anything?

View Poll Results: motor setup for scx10 c2 rig.
novak 13.5 crawler edition	1	50.00%
novak 18.5 crawler edition	1	50.00%
novak rockstar35t on 4s	0	0%
Voters: 2. You may not vote on this poll

09-02-2012, 04:39 PM	#1
jthellfire911 Rock Crawler Join Date: Jun 2010 Location: UTAH COUNTY Posts: 837	another brushless scx10 question... Ok.. so searching on my phone is a big pita. Plus I haven't really found the info I'm looking for so hence my questions .. I've got a 6lb ish scx10 with overdrive front gears, rr trans gears, mmp with ccbec, cs170 steering, 645/heyok winch, 1300mah 3s skylipos, spektrum rx/tx. Right now I'm running a novak rockstar 35t 20/86 gearing. So with that out of the way I'm looking for a brushless motor that will give me close to the same low speed control and faster high speed than my setup has now."I know its impossible to have the best of both worlds." So my thoughts are either 13.5 novak crawler, 18.5 novak crawler, or run my brushed motor on 4s for the high speed I'm wanting and carry lots of extra brushes with me. Thoughts and opinions. Go!

09-02-2012, 04:40 PM	#2
jthellfire911 Rock Crawler Join Date: Jun 2010 Location: UTAH COUNTY Posts: 837	Re: another brushless scx10 question... I do run in water and some mud and can corrosionx the motor and waterproof the sensor areas. All other electronics on the rig are waterproofed already.

09-03-2012, 05:30 PM	#3
jthellfire911 Rock Crawler Join Date: Jun 2010 Location: UTAH COUNTY Posts: 837	Re: another brushless scx10 question... Really no one? No thoughts on just going 4s with the brushed motor? Anything?

another brushless scx10 question... - Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
17.5 vs 18.5 brushless in an scx10	jebster	Electronics	13	01-18-2012 05:00 PM
Scx10 Kit, Lipo+Brushless	JohnyBeGood	Newbie General	8	07-06-2011 07:21 PM
scx10 brushless scalers	rickey420	Videos!	1	03-02-2011 04:25 PM
Best brushless for SCX10 rockracer	Diesel Dan	Axial SCX-10	23	11-25-2009 02:08 AM

Sponsored Links

RCCrawler Forums

Thread: another brushless scx10 question...